SUN MACHINERY CORP
Telephone: (516) 536 7375 Fax: (516) 536 7317
e-mail: rigs@sunmachinery.com
SHOP BUILT CABLE
TOOL/SWAB RIG
(Ref#10188) triple drum, friction
clutch, cathead (sandline holds 2400 of 5/8 line), mounted on tandem axle
Chevy truck with 427 gasoline engine, 8-5/8 x 45 single pole, new tires, power
steering, wireline unit, good usable rig for shallow oil/gas lease, drills,
workover, swab capabilities, no tools Price: $70,000 OFF
MARKET
SWAB RIG (Ref#351N) Mounted on 1993 Peterbilt truck with 22.5 tires and powered by Cummins L14 diesel engine, 4 hyd leveling jacks, 471 Detroit, Automatic transmission, 45 mast, 1600 swab line, weight 46,000#,, tooled Price: $155,000
SWAB RIG (Ref#1654N) Hydraulic rig, drum 48 x 18, new 6000 of 7/16 wireline, 353 Detroit on deck with 3 speed transmission, 24 x 5 square x Ό steel mast, mounted on 1999 Ford F450 truck with 7.3 diesel engine, automatic transmission, 2 hydraulic leveling jacks, drum operates with switch similar to air clutch, made from wireline unit Price: $80,000
FRANKS SWAB RIG (Ref#253Nb) Assembled in 1977, Franks drawworks, sandline drum 16,000 of 9/16 line, (currently has 13,500 of line), twin disc clutch, 50 hydraulically raised mast, traveling crown sheave, mounted on 1977 Ford LN9000 tandem axle truck powered by Detroit 6V92 diesel engine, (rebuilt 8/07 with 1900 hours), 10 speed Fuller transmission, 90 hp Franks PTO, tools 1-1/2, 2-3/8, 2-1/2 and tools. 2005 Dodge ½ ton Quad cab long bed pickup, automatic transmission. Doghouse on tandem axle trailer 800x15 tires and a 2 hitch. Price: $145,000
PULLING UNIT/SWAB RIG (Ref#835N) International truck with Detroit diesel engine, 40 telescoping mast, 10 ton winch, 4 line block, hydraulically raised mast and leveling jacks, bailing/swabbing drum, running condition, located Rockies Price: $18,000
COOPER LTO-550 SWAB RIG (Ref#504N) Manufactured 1980, Refurbished 2005, Cooper LTO-550 sand drum, mounted on 3 axle carrier with 6V71 Detroit diesel engine, 750 Allison transmission, leveling jacks, 16,000 of 9/16 sandline, 45 mast, 2 axle doghouse, completely tooled out, stored inside OFF MARKET
SKYTOP SWAB RIG (Ref#1091N) Manufactured 1970, air clutches, mounted on tandem axle carrier, Detroit 8V71 diesel with Allison 750 3-forward speed automatic transmission, 318 hp # 2100 rpm, 40 hydraulically raised mast, drum holds 20,000 of 9/16 line (has 18,000 of 9/16 currently), rig drives 55 mph on highway, leveling jacks. Work done: sandline reworked 2005, front end reworked 2006, hydraulic clutch assembly reworked 2006, shifter in cab reworked 2008, repaired bladder 2006, hydraulic brakes repaired 2005 Price: $150,000
HOPPER SWAB RIG (Ref#1100N) Manufactured 1980, air clutches, mounted on tandem International Paystar 5000 truck with 8V71T Detroit diesel, 13 speed Road Ranger transmission, rig drives 75 mph on highway, 362 hp @ 2100 rpm, 15,500 of 9/16 line, good condition, currently in use Price: $150,000
BREWSTER SWAB RIG (Ref#7425N) Single drum Brewster drawworks with air clutches and 12,000 of 5/8 sandline, Franks 52 hydraulically raised mast, 471 Detroit diesel on deck, Mountedon 1973 Mack tandem axle truck with 7-11 Mack diesel engine, Fleet crown wide sheave, double oil savers
Price: $90,000
WALKER-NEER CABLE TOOL RIGS 34 & 37 (Ref#978N)
6000 depth capacity, 3 available
A. WALKER-NEER 34 (Ref#978Na)
3 drums, spudder, 8-5/8 x 7 x 65 double pole, Tandem axle trailer with 5th wheel, 237 hp Mack in line 6 cylinder diesel engine, 4 speed transmission, Controls, gauges, battery starter, fuel tank, Excellent condition, Ready for immediate use. 7/8 line on 2 drums, 5/8 line on sandline drum Price: $90,000
B. WALKER-NEER 34 (Ref#978Nb) 3 drums, spudder, 8-5/8 x 7 x 65 double pole, Tandem axle trailer mounted with 5th wheel, 237 hp Mack inline 6 cylinder diesel engine, 5 speed transmission, Controls, gauges, battery starter, fuel tank, Excellent condition, Ready for use, 7/8 line on 2 drums, 5/8 line on sandline drum Price: $90,000
C. WALKER-NEER 37 (Ref#978Nc) 3 drums, spudder, 8-5/8 x 7 x 65 double pole, Tandem axle trailer mounted with 5th wheel, 237 hp Mack in line 6 cylinder diesel engine, 4 speed transmission, Controls, gauges, battery starter, Excellent condition, Ready for use. 7/8 line on 2 drums, 5/8 line on sandline drum Price: $90,000
WALKER-NEER S-32, S-33, AND C-34 (Ref#7028) Several at same location
(2) S-33, 6000 depth capacity, 7 x 8-5/8 x 55 double poles, single axle trailer, 140 Waukesha motor, main drive spudding shaft, clean condition, good looking heavy duty rig, complete Price: $32,000 each
(2) S-32, 5000 of wire, 5 x 7 pole, one good condition, one needs work Price: $32,000 for both
(1) C-34, 5 x 7 x 60 pole, mounted on Crane Carrier with Cummins diesel engine, 15 speed trans Price: $42,000
(1) C-24, 5 x 7 x 75 pole, trailer mounted, winch to raise pole, considerable amount of tooling Price: $25,000
WALKER-NEER S32 (Ref#5153) Workover rig, drilling, pull capacity 100,000#, drilling capacity 6 2500, 12 1400, 24 700, (2) 8-5/8 x 7 x 55 double poles, 3 drum, cathead, single axle trailer with dual wheels, 5th wheel, 2 screw jacks, 2 hydraulic jacks Price: $20,000
WALKER NEER C25A SERVICE RIG (Ref#6531N) Detroit 471 diesel engine, 5 speed, double drum, spudding beam, cable raised 8 x 10 double poles, triple sheave blocks and hook, 2 hydraulic levers, air controls, plumed for power tongs, weight indicator and rig floor. Mounted on 1981 International 2500 with 290 Cummins engine,10 speed Road Ranger transmission. Set of bales for blocks, 2-3/8 elevators, 2-3/8 air slips and controls, rod hook, 2-5/8 rod elevators and rod wrenches, 4-1/2 quick disconnect wire line socket,jars, stem and swab mandrels, 1-1/2 swab tools and mandrels, 4-1/2 sand pump, 1-1/2 x 4 BJ power tongs Price: $200,000
WALKER NEER P13A (Ref7085N) powered by Detroit 471N diesel engine, 8-5/8 x 7 telescoping mast pole x 40 high, 6500 of 9/16 swab line capable of pulling rods, mounted on a L10 International truck, 2 hydraulic levelers, air controls, 1-1/2 swab tools and mandrels, 4-1/2 swab tools and mandrels Price: $130,000
WILSON 38 SWAB RIG (Ref#884N) Low/high drum speed, new 40 shop built mast (manufactured from square tubing), 6V71 Detroit diesel and torque converter on deck, 14,500 of 9/16 line, Tubex line compensator, Mounted on 1993 Peterbuilt with 3204 Cat diesel engine and 13 speed transmission and 2 hydraulic leveling jacks, All tools Price: $225,000
WILSON SUPER SWAB RIG (Ref#6598N) 11,000 depth capacity, International diesel deck engine, 9000 of new 9/16 sandline, all new hydraulics, completely rebuilt, single drum, 35 hydraulically raised mast, mounted on 1981 Autocar 6-wheel drive with diesel engine, 2 rear hydraulic jacks, tools from 1-1/2 to 5-1/2, excellent condition, running daily Price: $170,000
WILSON SUPER SWAB RIG (Ref#6594N) 13,000 depth capacity, Detroit deck engine, 9,000 of new 9/16 sandline, single drum, all new hydraulics, completely rebuilt, 35 hydraulically raised mast , mounted on 1994 Oshkosh 6-wheel drive truck with diesel engine, 2 rear hydraulic jacks, excellent condition, running daily Price: $170,000
WILSON 42 SWAB RIG (Ref#345Nc) Mounted on 1992 Kenworth tandem axle truck, Cummins diesel engine on deck, Swab block Price: $110,000
WILSON SENIOR DD WORKOVER & DRILL OUT RIG (Ref#4137N) 4000 capacity, Double drum, 8x6 (reinforced single pole) x 55, Winch raised, Mounted on 1979 Mack tandem R truck with 35hp Mack diesel, 471 Detroit diesel on deck, Hydraulic leveling jacks, 6x8 oilwell duplex mud pump powered by Allis Chalmers 6 cylinder diesel deck engine, skid mounted, 25 ton King power swivel with Dodge power end, mounted on rig with hydraulic line to control, Support equipment: Skid mounted doghouse, Junk basket, 4 ½ x 35 casing rope socket and quick change knuckle, 5 ½ Miller sand pump, Currently working Price: $160,000
WILSON SUPER 38 DRILL RIG
(Ref#1593N)
Depth capacity 4,000, Single drum, Double pole, 250hp Walkershaw propane engine
on deck, 17-1/2 Gumbo Buster rotary table, Mounted on 2 axle trailer, (2) 13 x
102 poles, Raised and scoped by wire, 7-1/4 x 14 Oilwell duplex mud pump,
Powered by Waukesha propane 400hp engine on trailer, Traveling equipment, 3000
of 3-1/2 drill pipe, (10) 6-1/2 collar, Kelly & kelly bushing, Tools
Price: $125,000 PRICE REDUCED: $90,000
WILSON SUPER 38 (Ref#9685N) Single drum Wilson Super 38 drawworks, 1 drill line, 87 x 200,000# Wichtex mast hydraulically raised and scoped, mounted on 2 axle trailer, 3 back on substructure, (3) mud pumps: 6 x 16 Wilson Snyder duplex powered by 671 Detroit, 6 c 12 National duplex mud pump with diesel engine (all new fluid end parts), 7-1/4 x 14 Oilwell duplex mud pump with Cat diesel engine, new bearings in Brewster roraty table, new kelly hose, 20 kw Kohler light plant, 12 drill collars 5-1/4, 3800 of 3-1/2 x 31 drill pipe IF reg., pipe trailer, pipe basket, doghouse and fuel tank on float, 3000# Regan and accumulator, McKissick 50 ton block/hook, barrel type shale thaker, 500 bbl water tank, geolograph, new tires on doghouse and rig, new seals in torque converter, rebuilt weight indicator, new oil and filters in motors, recently drilled Price: $375,000
WILSON SUPER 38 WORKOVER RIG (Ref#505N) Manufactured 1999, double drum, 7/8 drilling line, 9/16 sandline, 8 brake, 72 x 140,000# Skytop Scorpion hydraulically raised mast, crown block, racking board, 300 hp Detroit 8V71 diesel engine (rebuilt 0 hours), and Allison 4460 transmisstion, controls, pulls doubles, mounted on (2) 10 x 46 I Beams as removed from platform. Price: $335,000
WILSON SUPER 38 WORKOVER RIG (Ref#5305N) Single drum, manufactured 1965, mounted on 4 axle carrier powered by 6V71 Detroit with 600 hours, 5 speed Spicer transmission, 74 4-leg hydraulically raised and scoped mast, working floor, recent work done on rig, good condition, 390 of 1 line, weight 72,000 lbs. Price: $155,000
WILSON 38 WELL SERVICE RIG (Ref#5123N) Manufactured 1969, double drum drawworks, 335 Cummins, 10 speed manual tranmission, Franks Servicer 125,000# 4-legged 74 double/single mast, mounted on 3 axle carrier, 50 ton 2-sheave McKissick block, Foster 74 tongs, 2-3/8 and 2-7/8 elevators, Guiberson air slips, bails, swab equipment, new clutch for carrier, sand drum will hold 11,500 of 9/16 sandline, currently working Price: $300,000
WILSON SUPER 38 (Ref#13387N) mounted on 4 axle carrier, 96 mast, 6V71 Detroit diesel engine Price: $335,000
WILSON 38 DOUBLE POLE RIG (Ref#4623N) trailer mounted, 671 Detroit engine, Ideco turntable, 40 kelly, 3000 of 3-1/2 bottleneck pipe, Gaso 7 x 12 mud pump with 671 Detroit engine, 1991 Mack winch truck, 45 float Price: $225,000
WILSON SENIOR WELL SERVICE RIG (Ref#7882N) double drum, 46 single pole cable raised, 1979 International Transtar 4300 tandem axle truck with Detroit diesel engine, Fuller 9 speed transmission, International V8 propane deck engine, 2000 swab line Price: $120,000
WILSON 42 SWAB RIG (Ref#345Nc) Mounted on 1992 Kenworth tandem axle truck, Cummins diesel engine on deck, Swab block Price: $110,000
WILSON SUPER 38 DD (Ref#345Na) Double drum, Mounted on 4 axle International carrier, 6V Detroit diesel & 10 speed transmission, 55 derrick Price: $175,000
WILSON SUPER DOUBLE DRUM (Ref#345Ne) Double drum, Mounted on 4 axle carrier w/6V92 Detroit diesel engine, 10 speed transmission, Double pole Price: $150,000
WILSON SINGLE DRUM 32 (Ref#345Nf) Double pole, Mounted on Ford 9000 Truck w/3208 Cat engine, 7 speed transmission Price: $55,000
FRANKS 44x33 WORKOVER RIG (Ref#7204N) 75% completed, requires work, 4500 depth capacity, 65 x 125,000# mast, Mounted on Ford L9000 tandem axle truck with Detroit series 60 engine, Manual transmission Price: $130,000
FRANKS 44 SERVICE RIG (Ref#15259N) double drum, double pole (2) 8-5/8 x 7 x 60 poles, 4400 swabbing, 4000 workover, 8V71 Detroit on deck, mounted on Mack tandem axle truck with Mack 300 diesel engine, 6 speed transmission, double frame CH613, 40,000# rear end, working rig Price: $125,000
FRANKS DOUBLE DRUM WORKOVER RIG (Ref#13393N) Double drum, mounted on 1980 tandem axle Paystar truck with Detroit 318 diesel engine, 70 mast, Cat 3208 diesel engine, Allison auto transmission Price: $235,000
CARDWELL H SINGLE POLE WORKOVER RIG (Ref#6222N) rated for 3000, mounted on single axle dual wheel trailer, 3000 of 9/16 sandline, Waukesha 6 cylinder engine, no tools Price: $85,000
FRANKS 33DD (Ref#9881) double drum pulling unit, 8 x 10 pole w/3-sheave crown, Ramsey hydraulic winch, Tulsa 28 winch, mounted on 1982 International 4300TA truck w/NTC 350 Cummins diesel engine, 2 hydraulic leveling jacks, 5 speed tansmission, 4 speed auxiliary, BJ tongs, Guiberson air slips Off Market
COOPER LTO-250 (Ref#285N) Double drum, mounted on Mack DH613 tandem axle truck with 16000# front axle and 44000# rears, 350 Mack engine, 9 speed manual transmission, new decking, (4) new leveling jacks, new 10 x 13 winch raised and scoped pole, hydraulic handling winch and tong arm to carry 5893 R tongs. Price: $435,000
Also available at extra cost is a 28 new doghouse
FRANKS DTM 33 (Ref#11273) double drum, 4000 with Ύ tubing line, Wabco air controls, mounted on 1979 GMC Brigadier and 6 x 4 truck with 6 cylinder engine and PTO, with manual screw jacks, Franks 7 26# x 5-1/2 20# double pole mast, 55 high, cable raised and scoped with single monkey board and tubing block, folding platform, weight indicator, hydraulic power tongs, Guiberson BOP 7-1/16 x 3000# BOP. Handling tools: BJ 2-7/8 elevators, rod hook, 50 ton bales, tubing spider, wrenches Located Southeast Asia Price: $150,000
Wichtex C65A D/D (Ref#1616Nb) T-68-100 derrick, Mounted on 1981 International F570 tandem axel truck with 350 Cummins, Oilfield front bumper, Full floating 31" x 8" double drum draw works, with air clutches, Franks right angle drive, 71' derrick cable raised and telescoped, 3 hydraulic outrigger leveling jacks, 450' of 7/8" tubing line, approx. 6,000' of 9/16" sandline, tool racks, tool boxes, Auxiliary hydraulic circuit, winch, cat head, McKissick 50 ton 2-sheave block
PRICE: $125,000 without tooling
PRICE: $135,000 with tooling
Walker Neer P5000 (Ref#1616Nc) 30" x 8" double drum draw works with air clutch's, Randolph drive, Mounted on International with 671 Detroit diesel, 65' mast raised and telescoped by hydraulic cylinders, 3 hydraulic outrigger leveling jacks. 450' of 7/8" tubing line, approx. 6,000'of 9/16" sandline, tool racks, tool boxes, Auxiliary hydraulic circuit, Sowa 50 ton 2-sheave block
PRICE: $125,000 without tooling
PRICE: $135,000 with tooling
Wichtex C30 (Ref#1616Nd) T-50-50 derrick, Mounted on 1979 Mack tandem axel truck with oilfield front bumper, Full floating 26" x 6" double drum draw works, with air clutches 250 hp right angle drive, 50' Y base derrick raised and telescoped by hydraulic cylinders, 4 hydraulic outrigger leveling jacks, 400' of 3/4" tubing line, approx. 4,000' of 1/2" sandline, tool racks, tool boxes, Auxiliary hydraulic circuit, winch, McKissick 30 ton 2-sheave block
PRICE: $125,000 without tooling
PRICE: $135,000 with tooling
SHOP BUILT 12 TON WATER WELL SERVICE RIG (Ref#14421N) Made 1994, 12 ton double drum winches, main line, sand line and hydraulic cat line, 40 hydraulically raised mast, catline raised scoping boom, 2 rear hydraulic leveling jacks, mounted on 1995 4900 International with DT466 International diesel engine, 6 speed manual transmission, Chelsea PTO Price: $55,000
SHOP BUILT PUMP HOIST (Ref#5507N) mounted on 1995 Ford F250 4x4 truck with 7.3 powerstroke diesel engine, Briggs & Stratton deck engine, 8,000# winch, no cathead or sandline, 2 rear hydraulic leveling jacks, no tools Price: $19,500
SHOP BUILT PUMP HOIST (Similar to 12T) (Ref#2016Na) mounted on 1984 Brigadier truck with 6V71 Detroit engine, PTO Price: $28,500
FAILING 430DD PULLING UNIT (Ref#8391N) Double drum, 42 telescoping mast, Johnson 30 ton blocks, air slips, Pennant weight indicator, 200 of 3/8 sandline (new), 5/8 mainline (new), new clutch pads, mounted on 1985 Peterbilt truck with 400 Cummins engine, 13 speed transmission, SK power tongs, good condition Price: $75,000
SMEAL 12R (Ref#9418) Manufactured 1980, double drum, mounted on Ford F700 single axle truck with gasoline engine, 42 x 45,000# capacity mast, 4000 sandline, field condition Off Market
SMEAL 12T (Ref#8587Na) hydraulic breakout, extra long back jacks, 14 steel bed with 6 heavy duty lock boxes, one single block, one double block and one triple block, remote control, pulled two pump, 4300 Custom International DT466 6-speed, 2300# rear air brakes, air drive seat, fully loaded Price: $130,000
SMEAL 10T (Ref#346N) Manufactured 2000, mounted on Ford 650 truck, Cummins diesel engine, PTO, 2 rear outriggers, set up for extra hydraulic tools, truck has 6 speed manual transmission, A/C, cruise control, dual winch, tail out winch, oil cooler, Price: $85,000
SMEAL 10T (Ref#1045N) Manufactured 1983, mounted on single axle Ford F700, Ford diesel engine, hydraulic breakout, cathead, 2 flatbed boxes, excellent condition Price: $50,000
SMEAL 10T (Ref#2313N) Manufactured 1980, mounted on International truck w/diesel engine, no cathead, no remote, 36 mast, breakout cylinder, mainline winch, sandline, leveling jacks, toolboxes, good condition Price: $40,000
SMEAL 10T (Ref#2999N) Mounted on 1980 International 2-ton truck w/DT466E engine, PTO, bailing drum, no remote, no cathead, no pipe or tools Price: $34,000
SMEAL 10T (Ref#189N) Manufactured 1975, PTO, mounted on 1990 Kodiak with Cat 3208 engine, 10 mast extension, 2 catheads, breakout cylinder, sandline, no remote (but wiring is there), 2 rear hydraulic leveling jacks, no tools available Price: $55,000
SMEAL 32B PUMP HOIST (Ref#11978N) gas deck engine, mounted on Ford F350 single axle truck with gas engine, complete POR
MONITOR PUMP HOIST (Ref#2281N) 6,000 8,000#, mounted on 1988 Chevy pump truck 4 wheel drive, 350 Chevy engine, 124,000miles, has new engine w/40,000 miles Price: $25,000
MONITOR M35 (Ref#10394Na) 30,000# capacity, sandline, aux line, mounted on International 1600 4-wheel drive truck with gas engine, PTO, 130 of new 5/8 line, no tools Price: $39,500
MONITOR M34 (Ref#10394Nb) 8,000# single line capacity, mast with 2 extension (37 total height), 130 of new 5/8 line, mounted on International 1600 4-wheel drive with gas engine, no tools Price: $37,500
MONITOR M33 PUMP HOIST (Ref#12576N) Manufactured 1986, mounted on Ford F700 truck with 4 cyl Detroit engine, 5 ton hoist, 36 mast, 2 rear hydraulic leveling jacks, utility box, no tools, no remote Price: $16,500
MONITOR M33 (Ref#4055N) 12,000# hoist, sandline, telescoping derrick, no tools, no remote, 2 rear levelling jacks, mounted on 1988 Ford F450 with gas engine, PTO, 400 of 5/16 line Price: 20,000
MONITOR M33 PUMP HOIST (Ref#12585N) mounted on 1980 Ford F450 truck (460 engine blown), 5 sp with service body, 3 ton hoist, no sandline, 35 mast, no tools, has remote but not wired, telescoping derrick Price: $16,500
MONITOR M33 (Ref#1996Na) Manufactured 1977, unmounted, telescoping derrick, remote available, no sandline, 2 rear hyd leveling jacks, no tools Price on Request
MONITOR 33 (Ref#15678) 33 telescoping derrick, remote control, custom designed two rear hydraulic stabilizing jacks, 8 steel deck, hydraulic driven pump pulling drum, two upright cabinets, two under deck boxes and two under deck fuel tanks, mounted on 2002 F550 Ford truck with 7.3 power stroke with 6-speed manual transmission Price: $75,000
MONITOR 33 (ref#2057N) mounted on 1988 Ford 2-ton truck with rebuit Jasper 370 hp gas engine, air brakes, 5 & 2 transmission, PTO, 1 winch, 2 rear hyd leveling jacks Price: $17,500
CASCADE 15 TON PUMP HOIST
(Ref#15408) 2 catheads, 5 lockable
toolboxes, tail out winch, mounted on 1985 International 4700 truck with DT466
engine, 5&2 transmission, good condition, working daily, one owner rig
Price:
$52,500 OFF MARKET
SMEAL 10T (Ref#188N) Manufactured 1987, 37 mast, mainline, sandline and tailout line, mounted on 1985 GMC 4x4 truck with Cat 3208 engine, PTO, 2 rear hydraulic leveling jacks, toolboxes, no cathead, no remote Price: $60,000
SMEAL 8T (Ref#2586N) Manufactured 2000, 40 telescoping mast, 21,000# pull line, 2 speed winch, mounted on Ford F550 truck with 7.3 powerstroke, 2 rear jacks, remote control, Omaha service body, toolboxes Price: $62,000
SMEAL 8T (Ref#7039N) Manufactured 1996, mounted on 1985 Chevy C6000 truck with Detroit engine, PTO, remote control, mainline, sandline, no cathead, 2 rear hyd leveling jacks, toolbox, no tools, pipe racks, good condition Price: $45,000
SMEAL 8T (Ref#12557) Manufactured 1988, mounted on 1988 Chevy C70 truck with 366 engine, PTO, extra pullout extension on mast, utility box Price: $40,000
SMEAL 8T (Ref#2758N) Mounted on 1978 Ford LN7000 truck with Cat 3208 diesel engine, PTO, tailout, power breakout, cathead, sandlne, remote, 13 utility bed Price: $40,000
SMEAL 6T (Ref#1084N) Manufactured 2008, mounted on 2008 Ford F450 4x4 truck with diesel engine, less than 6000 miles, remote control, sandline, 2 rear hyd leveling jacks, pipe racks, toolbox (no tools), excellent condition Price: $90,000
SMEAL 6T (Ref#3154N) mounted on 2001 Dodge 4x4 extended cab with diesel engine, mast extension, no remote, no sandline, 2 rear hydraulic leveling jacks, good condition, toolbox (no tools), pipe racks Price: $40,000
SMEAL 6T (Ref#698N) Manufactured 1998, 10 windmill extension with 4 extension, sandreel, remote control, pipe racks, headache rack, 13 flatbed with boxes, 1998 Ford F800 truck (not 4x4), Cummins diesel engine, no cathead, no tools, 2 rear hydraulic jacks, 500 sandline Price: $60,000
SMEAL 6T (Ref#4051N) Manufactured 1997, mounted on 2002 Dodge 1-ton 4x4 truck with Cummins engine, wireless remote control, no cathead, no sandline, 2 rear hyd leveling jacks, toolbox, pipe racks, good condition Price: $60,000
SMEAL 6T (Ref#15191) Manufactured 1997, mounted on 1995 Ford F450 truck with diesel engine, remote control, standard mast, hydrostatic, pipe rack, 2 rear hydraulic leveling jacks, no tools, good condition Price: $40,000
SMEAL 5T (Ref#57N) Manufactured 2006, mounted on 2006 Ford F350 4 wheel drive truck with Powerstroke diesel, 9 bed, 2 rear hydraulic jacks, remote control, 3 lines, 80,000 miles Price: $57,500
SMEAL 5T (Ref#1689N) Manufactured 2006, mounted on 1995 Superduty 12 long flatbed, 2 lines, main winch, sandline, 40 mast, remote control, 8 dual tool boxes, 2 rear jacks Price: $35,000
SMEAL 5T (Ref#10009N) mounted on 2006 F350 Super Duty 6.0L, remote, general bed with top boxes, pipe racks, 1 winch, 2 hydraulic leveling jacks, factory warranty, (not 4x4, no cathead, no sandline) Price: $55,000
SMEAL 5T (Ref#13843N) Manufactured 2005, mounted on 4 x 4 Ford F550 truck, 15,000 miles, 600 hours, like new Price: $70,000
SMEAL 5T (Ref#3122Ne) Manufactured 2005, mounted on 2006 Ford F373 truck, International diesel engine, 102,000 miles Price: $47,500
SMEAL 5T (Ref#935N) Manufactured 2004, mounted on 2000 Sterling truck (not 4 x 4) with Cat engine, remote control, 2 rear hydraulic leveling jacks, toolboxes, pipe racks, no cathead, no sandline, excellent condition Price: $95,000
Tools avalable at extra cost.
SMEAL 5T (Ref#2003N) 4-wheel drive, chrome wheels, aluminum body, 2 toolboxes, remote control, main wich, sandline, International 60 diesel engine, mounted on 2003 Ford 450 4 wheel drive truck, 2 rear jacks Price: $63,000
SMEAL 5T (Ref#6007Na) mounted on 2000 Ford F450 (not 4x4) 7.3 diesel, remote control, single line, pipe racks, toolbox, no cathead Price: $32,000
SMEAL 5T (Ref#15664) Manufactured 1998, mounted on 2000 Ford F450 4 x 4 truck with 7.3 liter diesel engine, PTO, standard mast, remote control, sandline, cathead, 2 rear hyd leveling jacks, toolbox, good condition Off Market
SMEAL 5T (Ref#2141N) mounted on 2000 Ford F400 4 x 4 truck with diesel engine, 2 line remote, utility boxes, 2 hyd leveling jacks, good condition Price: $49,000
SMEAL 5T (Ref#4569N) Manufactured 2000, mounted on Ford F350 2 wheel drive truck with 7.3 Turbo diesel engine, remote control, 3 hydraulic leveling jacks, 9 service body, no sandline, no tools Price: $40,000
SMEAL 5T (Ref#10205Na) mounted on 2000 4 x 4 Ford F450 truck with 7.3 diesel engine, A/C, pipe rack, hydraulic jacks, sandline, service box, Price: $45,000
SMEAL 5T (Ref#7678N) Manufactured 1999, mounted on 99 Ford F450 4x4 with V10 superduty diesel engine, cathead, 11 knapheide flatbed, remote control, 2 rear hydraulic leveling jacks, pipe racks, toolboxes Price: $40,000
SMEAL 5T (Ref#9022N) mounted on 1999 Ford F450 (not 4x4) power stroke, 44 derrick, sandline, oil cooler, cathead, mainline, 2 rear hydraulic jacks, toolboxes, no remote, no tools, Price: $50,000
SMEAL 5T (Ref#10205Nb) mounted on 4 x 4 Ford 4 x 4 Ford F350 truck with 7.3 diesel engine, A/C, pie rack, hydraulic jacks, sandline, service box, receiver hitch, welder Price: $40,000
SMEAL 5T (Ref#3524N) mounted on 1997 Ford F350 4-wheel drive truck with diesel engine, PTO, 44 boom with 10 windmill extension, sandline, remote control, toolboxes, pipe racks Price: $44,500
SMEAL 5T (Ref#1311N) Manufactured 1997, mounted on 1997 Ford (not 4 x 4) with 7.3 liter diesel, sandline, 11 utility bed, 2 rear hydraulic jacks, no cathead, no remote, no tools available Price: $34,500
SMEAL 5T (Ref#2597N) mounted on 1997 Dodge 3500 4 x 4 truck, Cummins diesel with 5 speed trans., hoist repaired, blasted and painted spring 2007, new aluminum flatbed Price: $40,000
SMEAL 5T (Ref#2182N) Refurbished 1997, updated and installed all new hoses on new truck 2004, rated load single part line 3,000#, 2 part line 6,000#, 3 part line 9,000#, 4 part line 12,000#, 31 hp gasoline engine on deck, diesel engine in truck, 33,000 miles Price: $42,000
SMEAL 5T (Ref#1733N) sandline, remote, pipe racks, 11 Knaphide bed, aluminum covered, mounted on 1999 Ford 4 WD truck, 6 speed, new tires, batteries, clutch brakes, rebuilt diesel, clean interior, good condition Price: $40,000
SMEAL 5T (Ref#2141N) 2 line remote, 2 hyd jacks, utility boxes, mounted on 2000 Ford F400 4x4 truck with diesel, very good condition Price: $42,500
SMEAL 5T (Ref#3548N) mounted on 1999 Ford F450 4x4 with diesel engine, Omaha 9 flip top box, cathead, sandline, remote control, pipe racks, good condition Price: $40,000
SMEAL 5T (Ref#2033N) mounted on 1999 Ford F350 XLT Superduty 4 x 4 truck w/7.3 diesel engine, service body, 3 leveling jacks, remote control, sandline, pipe rack Price: 42,500
SMEAL 5T (Ref#8170N) 1997, pipe racks, remote, Omaha service body, 1997 Ford F350 truck, 460, EFI, aluminum wheels, 5 speed transmission, stored inside Price: $39,500
SMEAL 5T (Ref#1733Nb) mounted on 1999 Ford 4-wheel drive truck with rebuilt diesel engine, remote control, sandline, 11 bed, pipe racks, good condition Price: $40,000
SMEAL 5T (Ref#6015N) mounted on 1996 International 4700 truck (not 4x4), with 444E engine, remote control, sandlne, no cathead, pipe racks, toolboxes Price: $39,500
SMEAL 5T (Ref#645N) Manufactured 1996 (redone 2003), mounted on 2007 Ford F550 4 wheel drive w/ powerstroke diesel engine, remote control, 38 mast, no Cathead or sandline, utility box, pipe rack, 8000 watt generator, hydraulically driven wire reel, 2 rear hydraulic leveling jacks, good condition, runs daily, no pipe or tools Price: $73,000
SMEAL 5T (Ref#1812N) Manufactured 1995, mounted on 1995 Chevy 4 x 4 truck with 460 gas engine, remote control, no cathead, new safety hook on mainline, free fall on sandline, 2 rear hyd leveling jacks, toolboxes, pipe racks, 650 of sandline, good condition Price: $45,000
SMEAL 5T (Ref#4361N) mounted on 1995 Ford F800 truck w/210 hp Cummins engine, 11 utility bed, standard mast, remote control, sandline, pipe rack, 2 rear hydraulic leveling jacks, no tools, good condition Price: $32,500
SMEAL 5T (ref#3430N) Manufactured 1993, mounted on Dodge 2 ton power wagon, less than 100 hours, (presently on Dodge 300 truck), OFF MARKET
SMEAL 5T (Ref#165N) Mounted on 1993 Ford 350 truck, 4 wheel drive, expandable derrick, winch, utility box Price: $29,500
SMEAL 5T (Ref#15446) Manufactured 1993, mounted on 1993 Ford F350 truck (duals in rear), with gas 460 engine, 3 leveling jacks, remote control, utility box, 1 winch, pipe rack Off Market
SMEAL 5T (Ref#4848N) Manufactured 1991, mounted on 1997 Chevy 3500 HD truck with Turbo diesel engine, triple line block with safety hook, no cathead or sandline, remote control, 8 utility body, 2 rear hyd leveling jacks, hand tools Price: $38,500
SMEAL 5T (Ref#1829N) mounted on 1991 Silverado 3500 4x4 truck, PTO, remote control, sandline, toolboxes, pipe racks, no cathead Price: $37,500
SMEAL 5T (Ref#2228Na) Manufactured 1990, mounted on Ford Superduty (not 4x4) with diesel engine, PTO, remote control, pipe racks, toolboxes Price: $17,500
SMEAL 5T (Ref#5338Nc) Manufactured 1990, diesl engine, hand tools, rod reel, mounted on 1984 Ford F700 truck Price: $28,500
SMEAL 5T (Ref#1188N) sand line utility body, pipe trough, mounted on 1989 Ford F800 truck with Ford 210 hp diesel engine, 10 speed transmission, tandem axle, air brakes, plumbed and wired for electric and air trailer bakes and lights trailer hitch (not 4x4, no cathead, remote control Price: $41,000
SMEAL 5T (Ref#12888N) Manufactured mid 1970s, mounted on International truck, remote control and sandline, 130,000 miles on truck Price: $31,500
SMEAL 5T (Ref#665N) double drum, mounted on 1989 FordF350 truck with diesel engine, 4 x 4 drive, complete, good condition Price: $22,500
SMEAL 5T (Ref#12034) mounted on 1989 Ford 700 truck with 210 hp Ford diesel engine, new tires, standard mat, sandline, rod rack, no cathead, bail line Price: $29,500
SMEAL 5T (Ref#2478N) Manufactured 1987, pto, mounted on GMC 1 ton truck with gas engine, remote control, sandline, 2 rear hydraulic leveling jacks Price: $20,000
SMEAL 5T (Ref#6787N) Manufactured 1986, mounted on 1996 Ford F350 4x4 with 7.3 diesel engine, PTO, remote control, cathead, 1 winch, pipe rack, toolboxes, 2 rear hydraulic leveling jacks, good condition Price: $55,000
Some tools available at extra cost.
SMEAL 5T (Ref#6009N) Manufactured 1986, remote control, sandline, 2 rear hydraulic leveling jacks, mounted on 1997 Ford (not 4x4) SuperDuty with 7.3 powerstroke diesel, utility boxes, pipe racks, good condition, well maintained Price: $40,000
SMEAL 5T (Ref#2044Na) Manufactured 1985, mounted on 1996 Chevy 3500HD, 454 Chevy Big Block gas engine, manual transmission, 300 of sandline, remote control, no cathead, Redding utility bed, L box behind cab, Price: $30,000
SMEAL 5T (Ref#10546) Manufactured 1982, mounted on 1990 Ford F800 truck with diesel engine, 4 speed transmission, 12,000# winch, sandline, (no cathead, no remote), good operating condition Price: $25,000
SMEAL 5T
(Ref#9569N) Manufactured 1978,
sandline, mounted on 1993 GMC 1 ton service truck, Chevy 450 Big Block engine, 4
wheel drive, 80,000 miles on truck, repainted, clean and ready to go
Price:
$40,000
OFF MARKET
SMEAL 5T (Ref#4029N) Manufactured 1971, mounted on 1999 Ford F450 truck, 7.3 liter diesel engine, 11 custom utility bed, 91,000 miles on truck, no sandline, great condition Price: $38,000
SMEAL 5T (Ref#2136N) 9 utility bed, remote control, toolboxes, not mounted Price: $17,000
PULSTAR P38000 (Ref#2264N) Manufactured 2009, 45000# hoist capacity, sandline (3000), 50 hydraulically raised mast, 3 winches, mounted on Pulstar 8W x 18 steel bed on 2009 Peterbuilt, Model 335, powered by Cummins 300 hp diesel engine, 4150 miles Price: $165,000
PULSTAR P38000HD (Ref#2155Na) Manufactured 2008, two available, mounted on 2008 Peterbuilt, 3000 sandline, 4600 miles, 40 mast, 45,000# heavy hoist, 3 winches, 4 jacks Price: $180,000
PULSTAR P38000HD (Ref#2155Nb) Manufactured 2008, mounted on 2005 Freightliner, 3000 sandline, 40 mast, 45,000# heavy hoist, 3 winches, 4 jacks Price: $180,000
PULSTAR P10000HD3L (Ref#6520N) Manufactured 2006, remote control, 40 tower height, solid aluminum pipe racks (2) with rack straps, front jack XL, mast mounted lighted with guards, HD tailgate, factory mount with hydrulic oil, throttle commander, Omaha standard 108D54VT lift top service body, aluminum fronts tops rears, stainless steel paddle latches, wire mounts front and rear, HD tow bumper and hitch, mounted on 2006 Ford F550 4x4 truck, A/C, 6.0 L power sroke diesel, 6 speed, locking differential, chrome bumper, AM/FM CD, tilt, cruise, HD rear suspension, SS wheel simulators Price: $80,000
PULSTAR 20,000# PULLING UNIT (Ref#7612N) Manufactured 2000, mounted on 550 Ford with 4 wheel drive, 6 speed transmission Price: $60,000
PULSTAR 12000 (Ref#14066N) Manufactured 1997, mounted on 1997 Ford F350 4x4 truck with diesel engine, PTO, sandline, 3 drums, 1 front 2 rear hyd leveling jacks, toolboxes, no tools, good condition Price: $55,000
PULSTAR 8000E (Ref#3806N) mounted on 2003 Ford F350 Superduty 4x4 truck with diesel engine, remote control, 9 body, no cathead, no sandline, 2 rear hydraulic leveling jacks, pipe racks, toolboxes, one owner rig, well maintained Price: $72,500
PULSTAR P7000 PUMP HOIST (ref#15214Nc) mounted on 2006 Ford F550 4-wheel drive truck with 6.0 diesel engine, 65,000 miles, hydraulic outriggers and holding valves, remote control, 37 tower height, (1) pipe rack made of solid sheet metal, HD tailgate, throttle commander, toolbox, HD tow bumper modified for vise, power to rear with special long hoses, special front ramp for wire spool, special base frame, 100 Series wirewinder, extension and nut wrench, poly pipe spool mount and poly pipe spool Price: $85,000
PULSTAR 7000 (Ref#3309N) Manufactured 2000, mounted on Ford 550 4x4 truck with diesel engine, sandline, 3 leveling jacks, toolboxes, pipe racks, good condition Price: $55,000
PULSTAR 7000 (Ref#699N) Manufactured 1996, mounted on Ford F350 4x4 truck with Ford 7.3 diesel engine, remote control, 37 mast, 45,000 miles, bailing line, pipe racks, service body, toolboxes, no cathead, sandreel 550 new Price: $55,000
5T PULSTAR (Ref#14948) Manufactured 1997, mounted on 1997 Ford F350 truck, V8 diesel engine, 4x4, 222,000 miles, includes various tools, wrenches, elevators, fittings Price: $35,000
PULSTAR 4T (Ref#12566N) mounted on 1996 Ford F350 4-wheel drive truck with 460 gas engine, 9 utility body, 1 winch, remote control, no cathead, 2 rear hyd leveling jacks, pipe racks Price: $35,000
SMEAL 4T (Ref#3074N) mounted on 1995 Dodge 3500 dually 4x4 truck with Cummins engine, remote control, no sandline, welder, generator, toolbox (no tools), pipe racks, 2 rear hydraulic leveling jacks Price: $37,000
SMEAL 4T (Ref#15298) Manufactured 1995, mounted on 1995 Chevy 4 wheel drive w/ turbo diesel engine, PTO, no sandline, remote control, welder, utility box, 2 rear hydraulic leveling jacks, good condition, currently drilling Price: $29,500
SMEAL 4T (Ref#12493N) mounted on 1987 Chevy 4x4 truck w/ 454 gas engine, remote control, no sandline, no cathead, utility bed, toolboxes, pipe racks, 2 rear hydraulic jacks Price: $35,000
SMEAL 4T (Ref#1996Nb) mounted on 1992 Chevy truck with 17 bed, 3116 Cat engine, PTO, remote control, 3 hyd leveling jacks Price: $19,000
SMEAL 3T (Ref#4348N) Manufactured 1993, windmill extension, mounted on 1997 Ford F350 SRW 4 x 4 truck with diesel engine, 5 speed, A/C Price: $28,500
SMEAL 3T
(Ref#1784N) mounted on 1992 4x4
Ford F350 truck, 460 gal engine, sandline attachment, good shape Price:
$35,000 Price Reduced to $27,000
SMEAL 3T (Ref#7601N) remote control, pipe rack, toolbox, mounted on 1990 Ford D250 truck with gas engine, 2 rear hydraulic jacks, no sandline, no tools, good condition, currently drilling Price: $29,500
SMEAL 3T (Ref#14806) mounted on 1989 Ford F800 truck with diesel engine Off Market
SMEAL 3T
(Ref#2351Nb)
Manufactured 1987, remote control, no cathead, mounted on Ford F250 4 x 4 heavy
duty with 460 gas engine, 9 flatbed with toolboxes
Price:
$20,000 OFF MARKET
SMEAL 3T (Ref#15519) Manufactured 1978, mounted on 1999 Chevy 1 ton 4 x 4 truck with diesel engine, utility bed, sandline, toolboxes, remote control, (no cathead), 2 rear hydraulic leveling jacks Price: $35,000
SMEAL 3T (Ref#1811Na) manufactured 1975, mounted on 1998 Chevy 1 ton 4 wheel drive, 6.5 diesel engine, toolbox, utility bed Price: $37,500
3T PUMP HOIST (Ref#793N) Mounted on 2001 Ford F350 truck, 7.3 diesel engine, 5 speed transmission, 8 tool bed Price: $30,000
SMEAL R2R (Ref#6007Nb) mounted on 1999 Ford F350 (not 4x4) 7.3 diesel, remote control, no cathead, toolbox, single line, pipe racks Price: $32,500
WORKOVER COMPANY FOR SALE (Ref#15466) Active company in Rocky Mountains
(3) SEMCO 15000: 2 manufactured 2002, 1 manufactured 1999, 40,000# capacity, mounted on Ford F800 truck
All rigs complete with power tongs,
Complement of crew trucks and support equipment
(6) Bowen power swivels
Drill collars
(3) Air compressors 900 cfm/350 psi: (all less than 5000 hours)
1 Manufactured 2000 Ingersoll Rand
1 Manufactured 1999 Ingersoll Rand
1 Manufactured 2004 Sullair
Price: $1,300,000
SEMCO S25000 WELL SERVICE RIG (Ref#1531Na) Manufactured 2005, NEVER USED, 52 x 84 wide hydraulically raised mast, boom capacity 50T-4 line down position, with lights. Main winch with brake capacity 25,000# single pull, cable 250of 5/8 diameter, speed 140 ft/min, hydraulic control. Sandline with air brake capacity 3000# single line pull, cable 2000 of 3/8 diameter, variable speed 480 ft/min, hydraulic control. Air shift PTO pump, hydro breakout cylinder, power tong hook up, mounted on used tandem axle Freightliner M2 with Cat C7 diesel engine, 4 hydraulic leveling jacks Price: $160,000
SEMCO S25000 WELL SERVICE RIG (Ref#1531Nb) Manufactured 2006, NEVER USED, 48 mast with lights, boom capacity 50T-4 line down position. Main winch with brake capacity 25,000# single line pull, cable 250 of 5/8 diameter, speed 140 ft/min, hydraulic control. Sanline with air brake, capacity 3500# single line pull, variable speed 480 ft/min. Air shift PTO. Hydro breakout cylinder, power tong hookup. Mounted on used 2006 International 4400 Navistar L6 tandem axle truck with DT466 diesel engine, 6 speed transmission. Price: $155,000
SEMCO S25000 (Ref#3167N) Manufactured 2001, 2 available
(1) mounted on 1994 International truck with new DT 466 engine (only 5500 hours), no sandline,
(1) mounted on 1996 International truck with DT 466 engine, new clutch and transmission, 2200 sandline
48 mast, 15 ton hook and block, single line pull, power tongs, slips, elevators, etc.
Fully tooled, ready to go, owner retiring
Price: $100,000 each.
SEMCO S-15000 WELL SERVICE UNIT (Ref#913N)
40,000# boom, capacity 1,000 of ½ line, 250 of 5/8 line
6000# tailout winch, hydraulic breakout cylinder
Aux. hydraulic valves, remote control, oil cooler
Semco 48H telescoping mast
Mounted on 1977 Ford tandem axle truck with Cat 3206 diesel engine, 5 speed transmission
Hydraulic leveling jacks, toolboxes
Byron Jackson Type C rotary tongs with 2-3/8 2-7/8 dies
Byron Jackson 2-7/8 elevators with 2-3/8, 1/9, 1.5 dies
1 set elevator bails
1 Byron Jackson 20 ton rod hook
1 Fish tape
2 Ύ 7/8 rod elevators, 1 rod elevators
2 Ύ 7/8 rod wrenches, 1 rod wrenches
3 1.9, 2-38, 2-7/8 water well elevators
Giborsen air slips with 2-3/8 2-7/8 dies and 1.9 wellhead plate
Lift clamp for oilfield pumps
Hydraulic spooling unit
Set pipe racks
2 set spooling racks
Set pump racks
Megger
4-3/4 sand bailer
Air banding tool
30 venture line
Space table
Snatch block for double line
Price for rig only: $55,000
Price with tools: $65,000
SEMCO S12000 (Ref#91N) Manufactured 2001, 36,000# capacity, 48 mast, dual 2 speed winch with grooved drum, twin cooler, mounted on 1989 Peterbilt tandem axle truck and Cat diesel engine, 15 speed transmission, Ingersoll Rand 185 air compressor with complete Ventura setup. Tools: air slips, power tongs, pipe wrenches Price: $85,000
SEMCO S12000 (Ref#9018N) Manufactured 1995, with wide derrick conversaion, sandreel, breakout cylinder, 18 ton triple line block with safety hook, (2) 96 toolboxes, factory mounted on 1987 IHC truck, diesel 5/2 speed PSPB, only used to set new steel casing in new water wells Price: $55,000
SEMCO S8000 (Ref#1924N) Double drum, mounted on 1989 International S1600 single axle truck with 7.3 ltr V8 engine, 5 speed transmission and 2 speed rear, 2 leveling jacks, 50 mast, double capacity lift Price: $15,000
SEMCO 8000 (Ref#11571N) Manufactured 2005, 42 hydraulic derrick, mounted on Ford 550 4-wheel drive truck w/diesel engine, excellent condition Off market
SEMCO S8000 (Ref#2276N) Manufactured 2003, Boom Capacity: 22,000 lbs.-3 part line Max. Vertical Boom Reach: 36, 40 & 46 Max. Horizontal Boom Reach: 12'6" Hydro System; Gear Pump 40 GPM @ 2,000 PSI Main Winch with Fail Safe Brake Planetary Gear Drive 60,000 in lb Capacity: 8,000 lb.. single line 16,000 lb.. double line 22,000 lb., triple line Cable: 180' of 1/2" diameter Speed: 130 ft/min. Hydraulic Control : Manual Sandline Winch with Disc Brake (free fall) Capacity: 3,000 lb.. single line Cable Cap: 1,500' of 3/8" diameter Speed: 450 ft/min. (Max.) Hydraulic Control : Manual Storage: 2 lockable tool boxes (96" x 13" x 16-1/2") 2 lockable tool boxes (78" x 13" x 16-1/2") 2 pipe storage racks Options: Direct Mount PTO Hydro Breakout Cylinder with Valve Remote Control-Main Winch Cathead w/ Valve Front Outrigger Auxiliary Hydro Valve Hydro Oil Cooler 12 VDC Steel Bed w/Deck plate 2 Speed Winch, mounted on 1990 Chevy 2-1/2 ton with gas engine, PTO, remote control, pipe rack, good condition Price: $55,000
SEMCO 8000 (Ref#4447N) Manufactured 1989, mounted on 1974 Ford 1-ton truck, PTO, no tools, hydraulic Price on Request
SEMCO S8000 (Ref#3162N) Manufacturd 1986, mounted on 2000 Dodge 1-ton 4x4 truck with Cummins diesel engine, PTO, remote control, no sandline, underbody boxes, toolboxes, 2 rear hyd leveling jacks, good condition Price: $42,500
SEMCO S8000 (Ref#6776N) sandline, block and tacle, 45 mast, mainline, 16,000# double line, mounted on 1993 International F1800 with L10E Cummins engine, PTO, 9 speed transmission, 2 rear hydraulic leveling jacks, no tools, good condition Price: $70,000
SEMCO S8000 (Ref#15677) Manufactured 1988, 1982 1-ton Chevy with gas, 44 derrick, sandline, auxiliary hydraulics, great condition, Price: $29,500
SEMCO 6000 (Ref#492N) Manufactured 2005, mounted on 2005 F550 Ford truck, 75,000 miles, very clean rig Price: $70,000
SEMCO 6000 (Ref#329N) Mounted on 2005 Ford F350 4-wheel drive truck, 40,000 miles, diesel engine, sandline, some tooling, good condition Price: $55,000
SEMCO S6000 (Ref#2180N) Manufactured 2004, 12VDC clutch pump, remote control, 2 pipe racks, 9 weld service body (red), factory mounting, mounted on 1999 F450 Super Duty truck with Tritton V10 engine, automatic transmission Price: $45,000
SEMCO 6000 (Ref#3525N) Manufactured 2001, mounted on 1999 Ford F550 2-wheel drive truck with 7.3 liter diesel engine, 36 boom, main line, (no remote, no cathead, no sandline), 2 rear hyd leveling jacks, pipe racks, toolboxes Price: $40,000
SEMCO 6000 (Ref#858N) mounted on 1997 Dodge single axlet ruck, good condition Price: $23,500
SEMCO S6000 (Ref#611N) Manufactured 1995, mounted on Ford F350 (not 4x4) with 460 gas engine, remote control, 4000 miles on new engine and clutch, 2 pipe racks, 3 toolboxes, 2 rear hyd jacks, good condition Price: $32,500
SEMCO S4000
(ref#12434N) mounted on 1985 Chevy
truck, 350 gas engine, PTO, 35 mast hydraulically raised mast, 2 leveling
jacks, running condition Price: $28,500 Off Market
SEMCO PULLING UNIT (Ref#8466) Manufactured 1979, all hydraulically operated, split drum, 65 x 60,000# (3 part line) hydraulically raised mast, mounted on single axle Chevy C70 truck with Chevy 427 gasoline engine, 2 hydraulic leveling jacks, no tools, good condition Off Market
JENSON PUMP HOIST (Ref#237N) derrick with telescoping single pole, mounted on 1990 F800 Ford truck, Ford 6 cyl Turbo diesel, PTO, outriggers, 14 toolbody (passenger side), main line, sand line, can pull 32, 14 layback, Price: $40,000
REICHDRILL EAGLE TWO PUMP TRUCK (Ref#3821N) Manufactured 2004, Ford F550 diesel engine, 76,000 miles, 18,000 pull, aluminum utility boxes, sandline, cordless remote, front downrigger Price: $87,500
FLEETMASTER PUMP HOIST (Ref#13839) mounted on 1987 Chevy truck with 350 gas engine, fully hydraulic, some tools, set up for 2 steel well, hydraulic shaft leaks, 150 of 15 pipe, drill head, swivel head, good operating condition Price: $32,500
FLEETMASTER PUMP HOIST (Ref#2809N) PTO, mounted on 1997 Ford F800 4 x 2 truck with 5.9 Cummins diesel engine, 2000# single line capacity, 14 bed with custom toolboxes Price: $52,500
CYCLONE FLEETMASTER F-40 PUMP HOIST (ref#15224) mounted on 1995 Ford F350 4x4 truck, 7.3L diesel, powerstroke, full power with air, 62,000 miles, 2 hydraulic leveling jacks, single drum, 34 hydraulically raised mast excellent condition Price: $30,000
CYCLONE F40 PUMP HOIST (Ref#1501N) mounted on 1994 GMC 1 ton 4x4 truck with 350 gas engine, PTO, cathead available (not on rig), stored inside, 2 rear hydraulic leveling jacks, good condition, currently drilling Price: $40,000
CYCLONE F40 PUMP HOIST (Ref#2903N) mounted on 1993 Ford Super Duty 4 x 2 truck with 460 V8 gas engine, 2000# single line capacity, 10 flatbed with headache rack, needs work POR
CYCLONE FLEETMASTER PUMP HOIST (Ref#14946) Manufactured 1981, 15,000#, mounted on 1981 Ford F600 truck with gas, 125 SDS Grimmer Schmidt compressor, used very little since 1990 Price: $35,000
FLEETMASTER PUMP HOIST (Ref#15404) approx 32 mast, walking beam, 250 gallon water tank and toolboxes, mounted on 1993 F450 4x4 truck, diesel 5 speed Price: $24,500
2 TON PUMP HOIST (Ref#158N) 1974, mounted on 1989 International truck, diesel DT360 International engine, spudder attachment, excellent condition Price: $42,500
SANDERSON CYCLONE PUMP HOIST (Ref#10544N) Manufactured 1978, double drum, hydrauulic twin disc clutch, mounted on Ford F350 with Ford engine, 4 speed transmission, telescoping boom, 400 of cable Price: $24,500
CYCLONE F100 PUMP HOIST (Ref#14735) mounted on 1985 Frord F600 truck, hoist a little older than truck, 10000# hoist Price on Request
CYCLONE PUMP HOIST (Ref#3131N) mounted on 1994 Ford F350 Super Duty, 7.3 liter diesel pump crane, 11,000GVW Price: $29,500
CYCLONE PUMP HOIST (Ref#13788) Manufactured 1981, 125 SDS Grimmerschmidt compressor, single drum, 1 front 2 rear hydraulic leveling jacks, 12,000# capacity, pipe rack, 75 of 5/8 cable, toolboxes Price on Request
CYCLONE PUMP HOIST (Ref#466N) mounted on 1993 Ford F450 truck, fiberglass utility boxes, POR
CYCLONE PUMP HOIST/SWAB RIG (Ref#273) Manufactured 1978, Capacity of 4,000#, split single drum, mounted on Ford F350 single axle dual wheel rear with 4 speed transmission, gasoline engine, tool boxes, 2 hydraulic leveling jacks, 5 speed transmission on hydraulic drawworks, 30 gallon hydraulic tank, twin disc air clutch, 2 piece square tubular boom retractable to length of truck expands hydraulically to 30, 400 of 1/4 cable, boom will tilt back to 12 behind truck to swab a well or pull a pump Price: $26,500
CYCLONE PUMP HOIST (Ref#5662) Manufactured 1975, Double Drum, mounted on 1989 Chevy with gas engine, 4 speed transmission, toolboxes, 35 2-piece tubular boom, pipe rack, 2 jacks, 200 cable Price: $22,500
CYCLONE F100 PULLING UNIT (Ref#10013) Manufactured 1990, mounted on Ford F350 single axle rear truck powered by 460 gaoline engine, 5 speed manual transmission, utility body, 10,000# capacity, aux sandline, remote control, hyd jacks in rear Price: $28,500
CYCLONE F30 PUMP HOIST (Ref#4785N) early 1970s, mounted on 1987 Ford F700 truck, Ford diesel engine, single line machine, no sandline, truck bed equipped with toolboxes, pipe rack, no tools Price: $25,000
CYCLONE 10 PUMP HOIST (Ref#491N) mounted on 1984 Railroad truck, power brakes, new battery, 500 of new pipe, 32+ derrick, 10 bit, stems, sockts.
1975 Chevy flatbed truck with Chevy gas engine, 14 ved, 250 gallon tank, steel racks Package Price: $20,000
COOPER PULLING UNIT (Ref#14544) double drum, 3rd drum for spudding 65 x 10 double pole raised by raised by drum, spud arm, trailer mounted, gasoline engine Price: $60,000
FRANKS DTM 33 (Ref#11273) double drum, 4000 with Ύ tubing line, Wabco air controls, mounted on 1979 GMC Brigadier and 6 x 4 truck with 6 cylinder engine and PTO, with manual screw jacks, Franks 7 26# x 5-1/2 20# double pole mast, 55 high, cable raised and scoped with single monkey board and tubing block, folding platform, weight indicator, hydraulic power tongs, Guiberson BOP 7-1/16 x 3000# BOP. Handling tools: BJ 2-7/8 elevators, rod hook, 50 ton bales, tubing spider, wrenches Located Southeast Asia Price: $150,000
PUMP HOIST 20,000# (Shop Built) (Ref#12779) mounted on 1995 International 4700 truck with diesel engine, hydraulic extended mast (37), 4 leveling jacks, 7 speed transmission, tool box Price: $32,500
PUMP HOIST (Ref#11750N) Shot Built, mounted on 1984 Chevy Series 70 single axle truck with rebuilt diesel engine, 27 mast, jib boom, hydraulic winch, two hydraulic jacks, very good condition, no tools or pipe Price: $30,000
WATER WELL SERVICE UNITS (Ref#5691N)
GROUTING TRUCK 1979 GMC C-65 series water truck, 720 gallon water tank, U2 stationary engine, Deck mounted grouting machine, 16 ft. deck, 4L8 Moyno pump, Built on side tool boxes Price: $13,000
PUMP TRUCK 1977 Chevy pump truck, Cyclone F-40 pump hoist, 366 V8 gas engine, 11 ft. tool boxes, Hydraulic brakes, Drive hammer Price: $18,000
Walker Neer P5000 (Ref#1616Nc) 30" x 8" double drum draw works with air clutch's, Randolph drive, Mounted on International with 671 Detroit diesel, 65' mast raised and telescoped by hydraulic cylinders, 3 hydraulic outrigger leveling jacks. 450' of 7/8" tubing line, approx. 6,000'of 9/16" sandline, tool racks, tool boxes, Auxiliary hydraulic circuit, Sowa 50 ton 2-sheave block
PRICE: $125,000 without tooling
PRICE: $135,000 with tooling
BUCYRUS ERIE 28L COMBINATION ROTARY AND
COMPLETION RIG (Ref#1059N)
Drawworks with spudding beams, 12 Brewster rotary table, 1974 tri axlw all
wheel drive with 6V53 Detroit, 180 Cummins deck engine, mechanical clutches, no
pulldown, breakout tongs, 4-1/2 x 38 kelly, 7 slim hole collars 5 x 25,
1500 of 2-7/8 drill pipe, pipe trailer, 7-1/4 x 12 Oilwell mud pump (skid
mounted) with Detroit V8 pwer, Price: $175,000