---

 

LIQUIDATION OF WYOMING DRILLING COMPANY

 

 

 

---

 

LIQUIDATION OF ROCKY MOUNTAIN DRILLING COMPANY

 

                   

 

 

 

---

 

 

DRILLING RIGS

 

 

CABOT 750 (Ref#12462Na)   

       

10,500’ depth capacity

Drawworks  Cabot 750 Double Drum Drawworks, 750 HP, Lebus grooved for 1 1/8” line, Air Operated Drillers Control Console, R&H 22” Double Hydromatic Brake, Crown-O-Matic, Kobelt 5028-CM Air/Spring Applied Combination Water Cooled Disc Break

Mast  Cabot Model 112-300, 112’H 4-Leg Telescoping Double Mast, 300,000 Lbs. Static Hook Load. Hydraulically Raised, 7 Sheave Crown Block, Crown Safety Platform, Ladder, Guylines.

Substructure 15’H Telescoping Substructure, 12'H Clear Height Ground to Rotary Beams

Carrier  All Above Mounted on Franks 4-axle Trailer, w/2 Engine Compound (2) Tru-Flo 1000 Air Compressors, (1) 175 Gal. Hydraulic Reservoir, (1) 100 Gal. Air Receiver Tank, (1) 200 Gal. Air Receiver Tank, (4) Leveling Jacks, (2) – 200 gal. Fuel Tanks, (1) Parker Hydraulic Winch 12,000lbs Capacity, (1) Hydraulic Motor Driven Quincy 390 Air Compressor, Folding walkways, Stairs, Safety Rails, 295/75R22.5 Rear Tires

#1 Engine – Caterpillar 3406 TA, Allison Transmission

#2 Engine – Caterpillar 3406 TA, Allison Transmission

Substructure  11’W x 15’H x 40’L Telescoping Substructure 12'H Clear Height Ground to Rotary Beams, w/ Rotary Beams, V-Door Ramp, Stairs, Safety Rails, (2) 12,000Lbs. BOP Lifting Hoists w/ Trolley Beams, 10'W x 4"H x 46'L Mud Boat, 8'W x 40'L Derrick Sub w/ Stairs

Rotary Table 17 1/2" Rotary Table w/ Split Master Bushings

Blocks/Hook 150 Ton Block/Hook Combination

Swivel 150 Ton

Kelly 4-1/4" x 38' Hex

Kelly Drive Bushings 4-1/4" Hex, Square Drive Kelly Bushing

Kelly Spinner Oil Works 1500 Kelly Spinner

Elevator Bails 250 Ton

Power Swivel Venture Tech, Model # XK-150, 150 Ton, 12,000 Ft/Lb. Torque @ 5,000 Psi.

Power Swivel Unit Venture Tech, p/b Caterpillar C-9 Diesel Engine

Accumulator 5 Station, 295 Gal. Tank, (12) 11 Gal. Accumulator Bottles Mounted on Water Tank Skid, w/5 Station Remote Control Mounted in Doghouse

BOP Equipment Hydril 11” x 5,000 psi Annular, Cameron Type “U” 11” x 5,000 psi 11" x 5K x 24"H Drilling Spool w/ (2) 4 1/16" 5K Side Outlets

Choke Cameron 3 1/8" x 5K, w/ (1) 5 way Block, (8) 3 1/8" x 5K Gate Valves, (1) 2 1/16" x 5K Gate Valve, (2) 3 1/8" x 5K Adjustable Chokes, (1) Buffer Chamber

Degasser 30"Dia x 12'L

Choke Line (1) 4 1/16" x 5K Gate Valve, (1) 4 1/16" x 5K HCR Valve

Kill Line (2) 2 1/16" x 5K Gate Valve, (1) 2 1/16" x 5K Check Valve

Mud Pump #1

National 8-P-80 Triplex Pump, 800 HP., Hydril K20-5000 Pulsation Dampener, Oteco 3” x 5,000 psi Shear Relief Valve, Teolegraph Pioneer Type D 0-6,000 PSI Pressure Gauge, Bridges Equipment Chain Drive Assembly, Master skidded w/ Caterpillar D398 Diesel Engine, Air Start, MCM 6" x 5" Centrifugal Charging

Pump, MCM 3" x 2" Centrifugal Liner Wash Pump

Mud Pump #2

National 8-P-80 Triplex Pump, 800 HP., Hydril K20-5000 Pulsation Dampener, Oteco 3” x 5,000 psi Shear Relief Valve, Type D 0-6,000 PSI Pressure Gauge, Chain Drive Assembly, Master skidded w/ Caterpillar D398 Diesel Engine, Air Start, National Torque Converter M/N C-300-64, MCM 6" x 5" Centrifugal Charging Pump, Mission Pedestal 3" x 2" Centrifugal Liner Wash Pump

Mud System

Two (2) pit, 700 bbl complete with four (4) 5”x6” centrifugal mixing pumps each powered by 50 HP electric motors, five (5) agitators each powered by 10 HP electric motors.

Two (2) Fluid Systems, Inc. High G-Force Linear Motion Shale Shakers

One (1) Fluid Systems, Inc. Vacuum Degasser

One (1) Fluid Systems, Inc. 3 - Cone Desander (10”Cones)

One (1) Fluid Systems, Inc. 12 - Cone Desilter (4” Cones)

Generator / Utility House

Generator # 1 - Detroit 350 Kw AC Generator, p/b Detroit Series 60 Diesel Engine, Electric Start

Generator # 2 - Detroit 350 Kw AC Generator, p/b Detroit Series 60 Diesel Engine, Electric Start

75 KVA Transformer

#1 Air Compressor - Quincy M/N QR390, p/b 20 HP Baldor Electric Motor

#2 Air Compressor - Quincy M/N QR390, p/b 20 HP Baldor Electric Motor

(2) Elite Series ECP80 Refrigerated Air Dryer

(1) 120 Gal. Air Receiver

All Above Mounted in 10'W x 40'L Skidded House

Water Tank

(1) Shop Built 10'W x 8'H x 30'L 425 Bbl. Water Tank w/ 20' Covered Porch

(1) Double Life 3" x 4" x 13" Centrifugal Water Pump p/b 30 HP Electric Motor

(1) Double Life 3" x 4" x 13" Centrifugal Water Pump, p/b 30 HP Electric Motor

Fuel Tank

12,000 Gal. Fuel Tank w/ 8'W x 12'L Pump House, w/ O'Drill Fuel Filter & (2) Roper 2AM12 Fuel Pumps p/b Baldor 5 HP Electric Motors, 4 Compartment Lubister, Shelving

Dog House 8'W x 20'L Dog House w/ (3) Lockers, Knowledge Box, Bench Storage, Lights, Heater

Change / Parts House 10'W x 40'L Skid w/ 20'L Parts House w/ shelving, w/ 17'L Change House w/

(20) Lockers, Bench, Lights, Heater, Table

Instrumentation Atlis Instrumentation Type FS, 300,000 Lb. Weight Indicator, w/ Pump Pressure Gauge and (2) Tong Line Pull Gauges, Rotary Torque Gauge, Atlis Instrumentation Automatic Driller 3-Pin Drilling Recorder

(1) Five Star Wireline Retriever w/ 15,000' of .092 wire

Handling Tools

(1 set) Type B Rotary Tongs w/ 3 1/2" - 5", 5" - 6 3/4", 6 5/8" - 9" Jaws

(1 set) Type C Rotary Tongs w/ 3 1/2" - 5", 5 1/4" - 7" Jaws

(1) 4" Woolley 225 Ton Drill Pipe Elevators

(1) 4" Woolley Drill Pipe Slips

(1) Type A 5 1/2" to 7" DC Slips

(1) Type A 6 3/4" to 8 1/4" DC Slips

(1) 6 1/4" DC Safety Clamp

(1) 8" DC Safety Clamp

(1) Pipe Spinner, Air Operated

Drill Pipe and Drill Collars TBD

Ancillary Equipment

(1) 5'W x 18"H x 50'L Catwalk 2 Pieces

(4 set) 18"H x 30'L Pipe Racks

(1) 3 1/3" x 55'L Rotary Hose

(3) MDL 800 Bug Blowers 24", 36", 48"

(1) 8' x 20' Parts Container w/ Shelving, Lighting

(1) Ingersoll-Rand 10,000 Lb. Man-Rider Winch M/N FA5AMR-24MK1G

(1) 8'W x 4'H x 20'L Junk Box

(1) Mud Bucket

(1) 75 KVA Camp Transformer

Price:  $5,500,000

PRICE REDUCED: $3,800,000

 

CROWN 1000HP (Ref#14886N)

 

 

 

           

   

 

 

Price: $5,300,000 

 

Price Reduced: $4,500,000

 

This rig is currently rigged up at location in Europe. The drilling began and the project was shut down.

Example of shipping costs:

36 truck loads, volume 1750 cubic meters, weight 450 ton

Shipping costs includes, loading and trucking to Hamburg Port, ocean freight to Libya (including unloading)

The loads are 6 open top flat racks, 8 container loads, 22 positions on ship

Shipping to Libya is €340,000

Shipping to Salvadore €267,500  (service every 14 days;  transit time 20 days

---

FAILING 90 STRATMASTER  (Ref#13405) 

             

5,000’ depth capacity, double drum, one block, mounted on 3 axle trailer 45’ long, Cummins 400hp diesel engine, 87’ x 200,000# Lee C. Moore jacknife mast, cable scoped and cable raised, designed as big rig, 18” rotary table, table 4-1/2’ from ground, (3) mud pumps:  Oilwell 7-1/4 x 14 duplex with Faywick air clutch powered by 440 Cummins diesel engine with 5-1/2” liners, Emsco 7-1/4 x 10” duplex mud pump with 350 Cummins diesel engine, with 5-1/2” liners, Oilwell 6 x 12” duplex mud pump with Cummins 300 hp diesel engine and 5 speed transmission with 5-1/2” liners, 1500’ of 3-1/2” drill pipe, (7) 4-1/2” drill collars, (6) 6” drill collars, 400 bbl laydown water tank, trailer mounted doghouse and near new handling tools, no sub, no BOP, no mud tank, good condition, 5 load rig  Price:  $525,000  Price Reduced  $275,000

 

---

 

GARDNER DENVER DW500  (Ref#11122N) 

       

Drawworks:  Gardner Denver Model SW500 drawworks, main drum grooved for 1-1/8” drill line and powered by (2) Cat C15 industrial engines

Parmac type V80 hydromatic brake

Mast:  136’ clear height Superior Derrick Services, 18’6” base, 600,000# GNC, 428,000# static hook load mast with crown cluster consisting of (6) 42” dia sheaves and (1) 55” dia fastline sheave, all grooved for 1-1/8” wire line

Substructure:  15’, box on box conventional substructure with 450,000# rotary capacity, 300,000# set back capacity and 750,000# simultaneous rotary and setback load

Travelling equipment:  Ideco Model UTB-265, 265 ton unitized hook/block combination, complete with (5) 36” dia sheaves, King Oil Tools Model 25MB-14, 300 ton capacity swivel, Owi Model 1500 kelly spinner.

Gardner Denver RT22-1/2” rotary table, chain driven off the drawworks rotary countershaft and complete with Varco MSPC solid body pin drive master bushing and type “20-HDP” pin drive kelly bushing for a 5-1/4” API hexagonal kelly

(1) Shaffer type LWS 11” x 5000 psi double ram type BOP

(1) type GK 11” x 5000 psi annular preventor BOP

(1) 5-station Koomey type 80 BOP controlunit, complete with remote control panel

(1) 2” x 4” 5,000 psi WP choke manifold

(1) 36” OD atmospheric degasser, unitzed on a single oilfield type skid.

Mud pumps:  (2) Hong Hau Model F1000 triplex mud pumps, powered by Cat D399TA diesel engines, suctions charged by a 6” x 5” Series 178 centrifugal pumps and Emsco style discahrge pulsation dampeners

Mud System:  (2) tank mud system of approx 773 bbl total capacity.  Shaker tank of approx 405 bbls with (2) 6” x 5” Series 250 centrifugal pumps, powered by a 50 hp AC electricmotor, (1) Derrick 12 cone desilter, (1) Derrick 2 cone desander, (1) Derrick vacu-flo 500 degasser, (1) Derrick DE-AG-7.5H, 7.5hp horizontal mud agitator, (2) Derrick FC313 linear motion shale shakers

Suction tank of approx 368 bbl with (2) 6” x 5” Series 250 centrifugal pumps powered by a 50 hp AC electric motor.  (4) Derrick DE-AG-7.5H, 7.5 hp horizontal mud agitators.  O’Drill 6” mud mixing hopper complete with venturi.

Water tank:  (1) 470 bbl capacity water tank, complete with (2) 3” x 2” Series 250 centrifugal water pumps powered by 20 hp AC electric motors.

Electrical System:  (2) 320 kw generators powered by (2) Cat C15 diesel engines, complete with switchgear and transformers.

Aux Equipment:  (1) Nov Wildcat automatic drilling system, (1) 4-pen drilling recorder, (1) retriever wireline measuring unit complete with 15,000’ of .092” wireline, (2) Ingersoll Rand FA2.5A-20XK1 air hoists complete with 5/8” wireline, (1) air powered chain driven drill line spooler.

Compressed Air System:  (1) Quincy Model QSB-40 air cooled rotary screw packaged air compressor unit delivering 165 cfm at 125 psi and powered by a 40 hp AC electricmotor and complete with 200 gal air receiver.  (1) Quincy Model QR390-20 unitized base mounted air compressor delivering 70 cfm at 125 psi and powered by a 20 hp AC electric motor.  (1) 500 gal air receiver mounted in the substructure.  (1) Airtek Model ECP165 refrigerated air dryer.  (1) Airtek model ECP80 refrigerated air dryer mounted in the substructure.

Rig Site Structures:  (1) drill floor house at driller’s position.  (1) crew change/toolhouse, (1) toolpusher quarters/office unit, (1) crew quarters unit.

Drill String:  4-1/2” OD, 16.60 lb/ft, Range II, Grade G105 drill pipe, 8” OD x 30’ long spiral drill collars, 6-1/4” OD x 30’ long slick drill collars, 4-1/4” square kelly, upper kelly valve, lower kelly valve, bit and cross over subs

Hanlding tools:  250 ton Handling tools for drill pipe and drill collars

Price:  $3,700,000

---

HALLIBURTON PUMP HT-400  (Ref#3510N) 

 

   

 

---

 

IDECO 725 TRAILER MOUNTED DRILLING AND WORKOVER RIGS  (Ref#2008N)

                 

SMST-M900 SERIES 116’ x 440,000# mast, manufactured 2008, overall height 120’, max hookload 360,000 lbs on 8 lines, 440,000 lbs on 10 lines, rated hookload 400,000 lbs. 10 lines, crown block 412,000 lbs rated capacity, 484,000 lbs max capacity.  Racking capacity 5” DP with 6-1/2” DC 8000’, 3-1/2” DP with 4-3/4” DC 11,500’, stabbing board, 9.8’ height adjustment, escape seat.

SMST 20’ M Partin 900 Substructure, manufactured 2008.  14’H x 18.04’ W x 10.58’ height under rotary beams, 290,000 lbs setback load, 330,000 lbs rotary load, 620,000 lbs max load (setback and rotary load), BOP handling system (trolley on two rails), 40,000 lbs static load

IDECO 725M DRAWWORKS manufactured 2006, mechanical drive, 750hp – 900 hp input rating, 44,500 lbs max single line pull (2^nd oayer), Parkersburg auxiliary brake Parmac V80, (2) Cat D3412 (475 hp)

1-1/8” diameter drilling line, sandline, Ideco dead line anchor

Emsco or similar block 489,5000 lb load capacity, Web Wilson WW250 hook 489,500 lb., Ideco TL-200 swivel 396,000 lb load capacity 6000 psi rated pressure

Auxiliary winches, Oilwell C-20.5 rotary table

(2) Continental Emsco F1000 triplex mud pumps each p/b Cat 399 engines

450 kw generator set with Cat D398

Air compressor station, BOP, Accumulator unit,

Located Europe

Price:  €1,450,000 (Euros)

 

---

IDECO H525  (Ref#44N)

         

         

Rig assembled, rebuilt and put in service in 2007
DRAWWORKS:
IDECO H-40 single drum, Lebus grooved f/1 1/8" drill line, Parkersburg 40" hydromatic brake w/overrunning clutch, Foster catheads, single engine compound p/b Cat 3412 (880 hp) diesel engine (2267 hrs on service meter), w/electric starter (new in 2007), radiator, gauges, Oilworks C-205-125 torque converter (Drawworks has been rebuilt to IDECO H-525 specifications, including new IDECO H-725 clutches-Work done in 2007)
MAST:
Lee C Moore S/T1053, 127’H x 13' 6"W x 450,000 GNC (290,000 static hook load capacity) cantilever mast, crown block with (4) 36" sheaves, 40" fast line sheave, derrick racking board
SUBSTRUCTURE:
14'H x 19'W x 43'L box on box with 3' 6" H x 9'W pony subs, built in parts room, (2) Ingersoll-Rand air compressors p/b electric motors, (2) 2" x 3" centrifugal pumps, Cat triplex pressure washer
GENERATORS:
(1) Cat 350 KW p/b Cat 3406E diesel engine, skidded (New 2008-970 total hours)
(1) Kohler 300R0Z71 300KW p/b Cummins NTA-19C diesel engine w/electric start, radiator, gauges, (555 hours on service meter)
Above mounted in 9'W x 40'L utility house w/electric control panels, KVA transformer, Champion screw type air compressor p/b 25 HP electric motor. Meyers accumulator is mounted in generator house.
MUD PUMPS:
Pump #1: Mudder MD-9 (GD PZ-9 design) triplex mud pump w/forged steel fluid end, Mudder pulsation dampener, 5" x 6" centrifugal charging pump, p/b Cat C27 (880HP) diesel engine (2294 hours on service meter), w/ air starter, radiator, gauges, Prep model EMPB0800BODR/HC transmission, mounted on skidded pump house. Pump bearings replaced with American bearings. Pump and Engine were new (late 2007)
Pump #2: Oilwell 218P duplex pump, Matco forged steel fluid end, w/quick change caps, Hydril K020-3000 pulsation dampener p/b Cat D-353 diesel engine, (2692 hours on service meter) w/air starter, radiator, gauges, drive assembly, skidded, mounted in skidded pump house.
ROTATING/TRAVELING EQUIPMENT:
IDECO 20 1/2" x 44" Rotary Table with split master bushing.
Oilwell 150 ton Swivel
4 1/4" x 39' square Kelly, upper kelly valve, lower kelly valve, inside BOP
EMSCO 200 Ton (4) sheave traveling block with BJ 4125 hook
(2) 2 3/4" x approx. 84" elevator links
BOP EQUIPMENT:
Shaffer type E 11"- 3000 # double ram w/4" pipe and blind rams.
Shaffer type 11” 3000# annular BOP (rebuilt and tested)
Approx. 12"H drilling spool w/ (2) outlets, (2) 4 1/16" gate valves, 2 1/16" gate valve, 2" check valve.
Myers Services 5-station 120 gpm closing unit w/(12) 10 gallon accumulator bottles, triplex charging pump p/b 15 hp electric motor, (2) air actuated charge pumps, skidded and mounted in generator house.(New 2007)
Myers electrical remote closing unit (Installed on doghouse wall)
4”x2” 3000# Choke Manifold w/4-way cross, (3) Cameron 2" 3000# gate valves, 4" 3000# gate valve, (2) adjustable chokes, type F pressure gauge, (New 2007)
MUD SYSTEM: 650 BBL Total
5'H x 10'W x 40'L mud shaker tank with 6'L porch, (3) compartments, M I Swaco Mongoose double screen linear motion shale shaker with (2) vibrator motors (new in 2008), 5 HP mud agitator, single cone desander, internal plumbing, MCM and SPD 5" x 6" centrifugal pumps p/b 50HP electric motors, top mounted walkways, (2) mud guns, skidded (pits rebuilt 2008 w/new plumbing, shaker, pumps & motors)
5"H x 10'W x 40'L mud suction tank with (3) compartments, top mounted walkways, internal plumbing, (3) mud guns, 10 cone desilter, skidded.
8'W x 16'L mixing house w/mud hopper, (2) SPD 5" x 6" centrifugal pumps, each p/b 50HP electric motors, steam heater, skidded, (New 2008)
RIG HOUSES:
Alta Fab 12'W x 38'L tool-pushers house, fully furnished, skidded. Rebuilt in 2008
8'W x 30'L top doghouse w/knowledge box, (10) lockers, cabinets, bench storage, steam heater, skidded
FUEL/WATER TANKS:
8'D x 30'L 8900 gallon fuel tank with (2) 1" x 1" explosion proof fuel transfer pumps, skidded.
8'W x 10'H x 30'L 400 BBL open top water tank, skidded
HANDLING TOOLS:
(2) Type B rotary tongs w/complete set of heads
(1) BJ Type “MGG” drill pipe elevator for 4" pipe
(1) BJ drill collar elevator 4 1/2” size
(1) Varco drill pipe slips 4” pipe
(2) Varco drill collar slips 6 1/2” & 8” sizes
(1) drill collar safety clamps
(6) drill collar lifting subs 4 ½” XH
(2) drill collar lifting subs 6 5/8” reg size
(6) X.O. subs
(1) Ingersoll-Rand HU40 air tugger (new 2007)
(1) Mud bucket
AUXILLARY EQUIPMENT:
(1)3 1/2" x approx. 55'L 5000# rated rotary hose,
(3)3 ½” X 15’ 5000# rated Vibrator hoses
42"H x 40'L catwalk
(1) 8'W x 34'L junk boxes, (1) w/5-compartment lubster
(4) 8'W x 34'L pipe baskets
Five Star hydraulic/electric wireline measuring device (new in 2007)
Fluorescent & mercury vapor rig lights and wiring (new in 2007)
Approximately 2000' 1 1/8" drill line & spool
Fisher type Reserve pit pump with hoses
Assorted had tools, parts, spares, steam heaters, fire extinguishers, etc necessary for drilling operations
(2) sets 40"H x 30'L triangular pipe racks
DRILL PIPE/COLLARS:
8611' (276 joints) 4" grade G, 14.40# range 2 drill pipe w/4"FH tool joints, 5 1/4"OD (New 2008)
1372' (44 joints) 4" grade G, 14.40# range 2 drill pipe w/4" FH tool joints, 5 1/4"OD. (NEW UNUSED)
(12) 6 1/4"OD x 2 1/4"ID x 31'L drill collars w/4 1/2" XH connections (New 2008)

Price:  $1,600,000

 

---

NATIONAL 370 (Ref#4421N)

7500 ft Cap.
Drawworks National 370 Powered by 60 Series Detroit hyd. Survey machine

Lee C. Moore 100 ft Derrick Freestanding 10 X 16 X 35 Sub Base 300000 lb Cap with Built in Water Tank 400 BBLS Cap. 1 Ideco 600 Duplex Pump Powered by 3412 Cat 1 Wilson 600 Duplex Pump Powered by 353 Cat 10 X 20 Top Dog House, Automatic DrillerDrilling Recorder Combination Generator House and Bottom Dog House 1/350 KW powered by 3406 Light Plant, 1/225 KW powered by 3306 Light Plant 600 BBL Mud System w/ Premix Compartment Shale Shaker, Desander 2 / 5 X 6 Centrifugal Mud Mixing Pumps 3- 5 HP Electric Pit Agitators All Handling Tools for DP & DC 17 1/2 National Rotary Table 14 /6 /6 1/4 Recessed DC Gardner Denver 125 Swivel 42 x 5 Hex-Kelly w/ Varco Drive Bushing Catwalk 5 X 45 2 Sets Pipe Racks 4 1/2 - X Hole Drill Pipe 7500 ft 3000 PSI 10 Annular BOP w/ 3 station closing unit

Price: $2,200,000      

 

---

OILWELL T66 (Ref#2566N)

 

 

 

Rated 10.000' w/ 4 1/2" drill pipe

Box on box sub w/5' pony sub, 14' high

131' x 300,000# Lee C Moore mast

INVENTORY:

Box-on-box: 9ft.  sub & 5ft. pony sub, Derrick is a 1952, 131 foot cantilever mast & "A"-frame;  with a max static hook load of 300,000lbs. on 10-lines .  Derrick has a racking capacity of 12,000ft. DP & Collars.   Crown section has 5-42" sheaves, w/one fast line sheave-56" grooved for 1-1/8"drill line.   A-frame mounted Dead Line spool, Lee C. Moore, 18" X 3-1/2"  300K-Martin Decker.    2 ea. 8"- 15 ton, McKissick Tugger line sheaves.   4 ea. 6" McKissick Tong block sheaves.   Stand pipe is 46ft. long, 4"-XXH, Stand pipe valve is a Baker, 2 X 4,  5000lb.  Sala Fall Arrester:  Certified, Model #3400407  Serial #102377.  Traveling Blocks are BJ-300 Ton,  5-sheave, ultimate 6259, W/swivel & hook.  Crown lighting, Strobe. Satellight, explosive proof.  Derrick lighting is 7-each, Hubble-Killmark Halogen and 19-each, Satellite Flourescent explosive proof electric lights.

Drawworks: Compound & Power:   Oilwell-66 Drawworks, air-over,  With a Lebus, 1-1/8" grooved drum, 2-Catheads, Make-up & Break-out. Unit is Mechanical drive, W/hydromatic,  350 LVD, Serial #20060614-056, Parmac V-80.  Compounded by a Superior model URC-700 compound, twin drive air clutch W/Low-High clutch range.  Compound mounted, Quency air compressor, Model #350-LVD, Serial #20060614-056 & Quency electric drive air compressor.  Engine #1 ,Series-60,  electric starter, unit #06R0808655, block serial #S50SCB7772070, electric control #H1801KL1, w/Gummi air clutch.  Engine #2, Series-60, model #6064/HK-33, Unit #06R0808634, Block #S60SCB7772049, Electric Control SR #H1801LGH,  W/Gummi air clutch,  24-volt electric starter.  Oil Works Torque converter, C195-100, Type-F, Serial #1179OWI, on motor #2.   Motor #1 Torque converter is out.  Rotary table, 17-1/2" Ideal.   Drawworks, Compound, Motors & Drillers console mounted on a 30-foot X 13-6" Skid, W/motor shed & fold-out wings.

MUD PUMP:  MD-9, Tri-plex,Sr.#5Z-1000-046, Mfg. Date: 04-25-07,Powered by Cat-398, W/ Electric charging motor, 50hp. & MCM 250-series  charge pump.  

MUD PITS:  1-Shale pit, W/Bandit double shaker, sand trap & three compartments.  Two risers,  two mud-guns & dump gates. 1-Settling-suction pit, 3-compartments, each compartment has electric agitator, Spur brand, electric 25hp., w/4ft-6inch long shaft & agitator.  25bbl., pre-mix tank, with mud hopper and discharge line into pre-mix tank.  Each compartment has dump-gate.   Shop-made stand for centrifuge.  Pins to shaker pit.  Both mud pits have explosive-proof lighting and electrical connections.

Dog House/Change House & Water tank Combo.   Dog house lowers into water tank for transport.  Water tank is 15ft. long, 8ft.-4in. wide and 7ft.-6In.high.

SCR HOUSE & 2-GEN SETS:

SCR house containes all explosive-proof connections for the drilling rig and mud pits & support housing.  All line connections are explosive-proof,as well as connection-boxes & switches.  Generator house #1 containes a Cat-3406, with 350KW gen-set and supporting switches and explosive-proof lines and connections. SCR Gen set serial #CBB3L5437.   Generator house #2 containes a Cat 3406 & a 365KW gen-set,  with explosive-proof connectors and electrical lines.  Serial #G6B01214.  Each Gen-set and SCR-unit are contained in seperate BERCO 20ft. Metal House.    2-Suitcases for fuel & electrical lines.  SCR house & both gen-sets, new,(One-hole drilled.), are house in seperate, (Berco, 20ft.X 8ft. houses).

One Berco tool shed/change house.  20ft. X 8ft. metal building.

Rig fresh water pit,  8ft.wide X 30ft. long X 4ft.high, W/Rig Washdown Pump:  Cat pump, Model 5CP3120,w/ electric 115/240 3-phase electric motor.

16ea.-Drill Collars,  6-1/4" X 30' random.  Inspected & like new.    4-Sets pipe racks.  24" high X 28ft. long.    Cat Walk, 24"high X 42ft. long.

Misc. Hand tools & Handling tools, subs, elevators etc.

One Pusher house, skid mounted, 2-bedroom, Shower & Kitchen W/office.  12ft wide X 44ft. long.  Electric heating & cooling, like new.

125hp., Cleaver-Brooks boiler, 480-volt,  housed in skid-mounted boiler house, 10' X 32' steel building w/double front doors.

Floor has wind-walls, custom made.

PRICE: $ 1,300,000

---

 

 

OIME 1000  (Ref#2079)

 

 

142’ Parco SL-7 x 1,000,000# mast

Cat 3412 900 hp diesel engine (requires rebuilding)

Allison automatic transmission

Water cooled brake

Nitrogen radiator with large fan

Enclosed driller’s console

Shop built top head

(2) Tulsa 1250 hydraulic wrenches

Iron Roughneck will handle up to 7” drill pipe and 11” collars

Mast can stand 120’

Hydraulic racking system

Equipped with big hole gooseneck and reverse for air drilling

Mounted on American Crane crawler tracks with Cat 245 pin to front for rig moves

Rig can move from location to location with the mast in the air

Air tanks, air compressor

Hydraulic pumps

Hydraulic system all stainless steel

Large V-door which will accommodate large load up to rig floor

Sliding floor which opens to 80”

Has set 3,000’ of 24” x ½” wall thickness casing

Capable of setting 5,000’ of 24” x ½” wall thickness

Stacked in Southeast USA

Price:  $550,000

 

---

 

SKYTOP BREWSTER TR-800  (Ref#2219N) 

       

Reconditioned rig,

Double drum drawworks H14610-38, main drum (2) twin disc clutch 46 x 10 brake, sandline drum twin disc clutch 38 x 8 brake, hydromatic brake V80, 2 engine compound

(2) Detroit 60 Series 475 hp Tier I engines, Allison transmssion CLT-5860-4 (5 speed), no rotary drive,

115’ x 410,000# telescoping mast, 8 blocks, 1-1/8” drill line size,

100,000# total axle suspension,

Racking board capacity 10,080’ of 4-1/2” drill pipe,

20’ floor height trailerized substructure, rig completely reconditioned, certified detailed inspection available 

Price:  $1,450,000

---

 

---

UNIT 34 (Ref# 3212N)

   

1 – 103’ LCM Derrick 300,000 lb Crown 6 Sheave 29” x 1 ½” 6 x 6 5/8” Thick Angle Iron

1 – U34 Draw works w/hydromantic brake powered by new 8v92 Detroit Rebuilt Right Angle Drive Torque Converter New Line

GxN 16” Garner Denver Mud Pump Skidded & Reskidded w/mato fluid end powered by 12v92 Detroit rebuilt with day tank

Two piece sub base 6’6”

Two piece Pony sub 43’ – 1 22” x 11’ x 36” Kansas Type Base

1 – Two Piece Cat Walk 40’                                                              1 – 100 Ton 3 Sheave Block

1 – Ideal Type F Swivel with Quick Change Packing                   1 – Rat Hole Digger Complete

1 – Brewster 17 ½” Ball type Rotary Table                                     1 – Set Wilson AAx Tongs

1 – 8’ x 20’ Doghouse                                                                        1 – Shaffer BOP

1 – 10’ x 25’ Water Tank                                                                    1 – Pipe Baskets

1 – 40’ Kelly                                                                                          1 – Kelly Bushing

1 – 100KW Kato Generator                                                                1 – Centerfugal Pump 20 HP elec.

1 – Duplex Pumps 4 x 6 Wheatley Power 4 cyl John Deer Diesel

1 – Derrick Stank                                                                                 1 – Desander Cone Type

1 – Tandem Dolly Trailer for Derrick                                               1 – Set 4 ½” Slips

1 – Bottom Hole Change Over Sub                                                 1 – Mud Hopper

2 – Tanks 100 gal. Oil                                                                         1 – 100 gal Diesel Tank

1 – V Door                                                                                             3 – Sets of Steps

Price: $850,000

PRICE REDUCED:  $700,000

---

WALKER NEER CC-2000 (Ref#6698N)

           

DRILLING UNIT:

1974 Walker-Neer CC-2000 complete with the following attached equipment:

Franks 58'H x 80,000# GNC, 60,000# static hook load-hydraulically raised free standing mast, derrick racking board, Double drum drawworks with air clutches, Hydraulic pull down, (2) McKissick (2) sheave traveling blocks.  4 1/4" x 35' kelly.  GD model FD-FXX 5 x 8 duplex mud pump w/surge chamber, 3 x 4 centrifugal charge pump, and Cat triplex water injection system.  (4) hydraulic leveling jacks.  Franks 8 1/2" retractable rotary table, hydraulic breakout cylinder.  Hydraulic/electric wireline measuring device. Rig is mounted on 1974 Universal (4) axle crane carrier with Cummins 400 big cam and Allison 750 Transmission-PTO driven.  425/65R22.5 front and 11R24.5 rear tires, and Budd wheels

 

SUBSTRUCTURE/RAMP:

42" H x 8' 11" W x 39' L "T" back on ramp, 8' from top of kelly bushing to ground,

42" H x 8' W x 39' L "T" type doghouse stand

(1) 7'6" W x 36" H x 34' L combo pipe tub/walkway

 

GENERATOR HOUSE/WATER TANK/FUEL TANK/ACCUMULATOR

Mounted on 8’ W x 50’ L skid

100KW Generator w/6 cylinder turbocharged Waukesha diesel w/electric start, radiator, and gauges.  25 KVA transformer and air compressor. (1) 1200 gallon fuel tank & (1) approx. 1600 gallon water tank

Payne 2-station 40 gallon closing unit

 

MUD PUMP:

Skytop Brewster B-550 duplex pump w/Mattco forged steel fluid end w/quick change caps, Hydril pulsation dampener, Type D pressure gauge, p/b Caterpillar D-379B diesel engine w/radiator & gauges. Skid mounted

 

BOP/WELL CONTROL:

(CAN BE PURCHASED SEPERATLY)

MUD SYSTEM:

85 BBL capacity, with 7/6" W x 5' H x 18' L (2) compartment mud tank, 3'L porch, Brandt 4" x 5" shale shaker p/b 5HP electric motor, Mission Magnum 5" x 6" centrifugal pump p/b 40HP electric motor

 

RIG HOUSE:

(1) 9' W x 28'L top doghouse w/9 lockers, knowledge box, bench storage, skidded

 

HANDLING TOOLS:

(2) BJ type LF tongs w/complete sets heads

(1) BJ 3 1/2" 30 ton bottleneck elevator

(1) 3 ½” Drill pipe slips

 (1) Raugeh Mfg. air over hydraulic pipe spinner 2 7/8" to 7" capacity

AUXILLARY EQUIPMENT:

Assorted hand tools, parts, spares, fire extinguishers, etc necessary for drilling operations

Martin Decker weight indicator

Western 40PG (40 ton) Swivel

PIPE BASKET/CATWALK COMBO:

7'6"W x 36"H x 36'L pipe basket/catwalk combination

DRILL PIPE/DRILL COLLARS:

1100' (35 joints) 3 1/2", grade E, 13.30# drill pipe w/3 1/2"IF tool joints

 (4) 6"OD x 2 3/8” ID drill collars

(1) triangular pipe racks

 

Price: $415,000

 

---

WILSON 75 (Ref#1621N)

       

Wilson 75 drawworks, 23 McKinney hydromatic brake,

Lee C Moore 129’ x 18’6”, 10 line 1-1/8” crown and block,

16’ x 50’ box on box substructure, (2) CAT 3406B diesel engine and (2) National torque converters, Ideco 23E rotary table,

250 ton YG225 traveling block, 180 ton mud king swivel SWU180, Kelly spinner OWI1500, 5-1/4” x 40’ hex kelly,

Wireline unit, Pipe spinner, Vortex Shale Shaker,

Emsco F-800 mud pump w/ CAT D-3508 diesel engine and 1 MCM charger pump,

Gardner Denver PZ9 mud pump w/ CAT D-398 diesel engine and WPT transmission,

#2 Mission M charger pump, CAT D-3406 320 kw generator,

3 Pit mud system 1500bbl, New shale shaker, new desilter, new desander,

New centrifugal pump, New electric motors, Rebuilt mud agitators,

Suction pit w/ built in 50bbl slug, 4 station 12 bottle accumulator,

11” x 5000# Shaffer double E BOP, 11” x 5000# Hydril annular BOP, 4-1/16” & 2-1/16” x 5000# Choke Manifold with gas buster,

10,000 gallon fuel tank, 450 bbl water tank, Pushers hose, Crew hose, Dog house, Change house/Parts house,

10,400’ of 4-1/2” XH G105 double white drill pipe, (24) 6-1/8” x 2-3/8” x 30’ drill collars, Catwalk & pipe racks, Subs. 

Necessary equipment needed to run rig. Rig drilled 4 wells since rig up  

Price: $4,600,000   PRICE REDUCED:  $2,450,000

---

WILSON 4500’ DRILL RIG (Ref#7146N)

       

Wilson drawworks

6” brakes, 12” drum, ¾” drill line

Air clutch

300hp Cummins diesel

56’ mast

Mounted on heavy duty oilfield trailer

Square kelly 35-1/2’

New Hacker swivel

12” Brewster rotary table

1550 Gaso duplex mud pump w/ Cummins diesel engine

Mounted on 2 axle truck

500 gallon fuel tank

Complete with all tools including tongs, subs, 7/8 hydraulic winch

Heavy duty pipe trailer

3000’ of 2-7/8” drill pipe

5 drill collars 4” x 30’

Price: $220,000  PRICE REDUCED:  $200,000

---

 

ZJ40 1000 HP RIG  (Ref#977N)

 

1. Rig ZJ 40 Triple 1000 HP.

2. Draw works JC 40C Rated HP 1000 mechanical, hydraulic disc brake with Crown-O-Matic.

3. Power 3 x Caterpillar D398B engines with high temperature radiators, three

National torque converters driving main compound, all furnished with

rig saver shut downs and spark arrestor silencers suitable for Zone 1 operation on skids

with rain hoods.

4. Hydromatic Brake DS40S Eddy current electric magnetic brake 27 500 ft lb.

5. Drums 27 in X 56 in drum diameter Lebus grooved for 1 ¼ in line.

6. Mast JJ250 / 43 –k 555,000 lb 141 ft high with racking capacity for 12 000 ft of 5 in drill pipe.

Mast designed to accept top drive. For derrick climbing 2 x fall arrester safe line devices

and two easy riders installed

7. Substructure DZ 225/ 25 ft high substructure with height under rotary beams 21 ft.

Max rotary load 555 000 lb, set back capacity 320 000 lb with two rig floor tugger winches

each rated at 5 tons each.

Full drip tray mounted on bell nipple under rotary table for containment of any spillages.

8. Travelling Block Ideco 265 ton block/hook combo with 5 x 42 in sheaves.

9. Drilling line 5000 ft of 1 ¼ in 6 x 19 EIPS regular line mounted on an electric drill line spooler

10. Rotary Table 27 ½ in rotary table with bushings 1, 2 & 3 supplied, rated capacity 300 000 lb, 0-300 RPM.

11. Swivel Gardner Denver 300 ton swivel with Varco S6600 hydraulic Kelly spinner, 6 5/8 in LH

connection. Max working pressure is 5000 lb/in2.

12. Kelly 5 ¼ in Hexagon 40 ft, 6 5/8 in top connection, 4 ½ in bottom connection with 2 ½ in bore.

13. Mud Pump No. 1 F-1000 triplex pump 1000 HP with 5 in x 6 in belt driven charge pump.

Tail driven from compound transmission

14. Mud Pump No. 2 F-1000 triplex pump 1000 HP with 5 in x 6 in belt driven charge pump.

Tail driven from compound transmission

15. Mud pump No. 3 F-1000 triplex pump 1000 HP with stand alone Caterpillar D-399 diesel driven by National

torque converter with 5 in x 6 in charge pump belt driven. Hydril pulsation dampener with

pop-off and bleed-off with lines back to tank system.

16. Rotary Hose 4 in ID x 62 ft long, 6000 lb/in2 W/P with 4 in Fig 602 connections.

17. Tanks 22 bbl trip tank stand alone with 2 in x 3 in fill pump. Also a 3 in air pump for back up.

400 bbl water tank with transfer pumps

18. Rig Generator Two Caterpillar D-379B diesel engines each with 460 V 500 Kva 50 Hz generators

housed in acoustic enclosures.

19. Mud Systems Four tanks in total including two active tanks, mixing tank, settling tank.

1250 bbl total capacity with seven agitators, Vac 1000 vertical vacuum degasser and poor

boy degasser complete with tank covers.

Three high speed Derrick Super-G linear motion shale shakers

20. BOP Equipment 13 _ in 5M annular preventer, H2S service to API Specification

13 _ in 5M Cameron double gate preventer complete with pipe rams and blind rams. H2S

service to API Specification

13 5/8 in drilling spool with 2 x 3 1/8 in 5000 lb/in2 outlets

21. BOP Accumulator Koomey 6-station 180 gal unit with two air operated charge pumps.

Electric charge pump

22. Choke manifold 3 _ in WKF 5000 lb/in2. 9-valve choke manifold with auto choke and manual

adjustable choke.

23. Kill line Two manual 3 1/8 in x 5000 lb/in2 valves

3 1/8 in full hole NRV 5000 lb/in2

24. Choke Line 3 1/8 in manual 5000 lb/in2 valve

3 1/8 in HCR 5000 lb/in2 valve

3 1/8 in Coflex hose 5000 lb/in2

25. Drill Pipe 12 000 ft 5 in 19.5 lb/ft G 105 with 5 in XH (4 ½ in IF) connections

12 joints of 8 in drill collars with 6 _ in Reg connections, 150 lb/ft.

18 joints of 6 1/2 in drill collars 4½ in IF connections, 92 lb/ft.

15 joints of 5 in HWDP with 4½ in IF connections, 50 lb/ft

4 pup joints 5 in with 4½ in IF connections

26. Bit subs & crossovers Full crossover and bit sub inventory to suit Contractor’s tubulars.

27. Elevators To suit Contractors tubulars.

28. Slips To suit Contractors tubulars.

29. Tongs Type SDD tongs 4 in through 17 in.

30. Bail Arms One set of 8 ft 350 ton bail arms

One set of 15 ft 350 ton bail arms

31. Safety clamps Varco unit from 3½ in through 8 in.

32. Spinner Varco SSW-30 hydraulic drill pipe spinner.

33. Air source room 2 x 50 HP LS-12 Sullair electric driven screw compressors

including air dryer system and two 600 gal receiver tanks

34. BA sets Two 1 hour sets.

35 Fork truck JCB 535/125 fork truck and pipe grab.

36. Tool shack 40 ft office and workshop for mechanic with welding set and cutting tools. Full facility

with tools, press and drill

37. Pump spares room 20 ft pump spares room with all consumables situated next to pumps

38. Hosery 20 ft hosery shack and lifting equipment, full spares for hydraulic hoses and all lifting

equipment

39. Welfare Shower shack and locker room for crew with washing area

40. Spares 40 ft Container with full spare parts inventory.

41. Offices Toolpushers office.

42. Fuel 14 000 gal bunded fuel storage with oil storage.

43. Casing tong Model TQ340/35 13 5/8 in casing power tong with jaws from 5 ½ in to 13 3/8 in

44. Casing Handling Elevators form 5 ½ in to 13 5/8 in

Equipment

45. Iron Roughneck Model ZQ 203/100 80’000 ft lb max rated, from 3½ in drill pipe up

8 in drill collars

46 Survey unit Matthey type survey unit with 7000 m of 0.092 stainless steel wire line

and Sure Shot 0-7o survey instrument.

47. Water pump 6 in Sykes diesel driven water pump

48. Mobile Welder Lincoln diesel driven 300 A welding set

49. Flare stack Vertical mounted flare stack with 200 ft of 4 in flare line

Located West Africa

PRICE:  $10,400,000

 

---

WORKOVER RIGS

---

FRANKS 658 WORKOVER RIG (Ref#565N) 

Double drum, 8000' of 5/8" sandline, Blocks, 65' x 150,000# square tubing mast hydraulically raised and scoped, Mounted on Loadcraft tandem axle rear single axle front, With 671 Detroit diesel and power box, 4 hydraulic leveling jacks, Rod basket, Tubing board, No tools   

Price: $200,000  PRICE REDUCED:  $175,000

---

HOPPER GXXHTA WORKOVER RIG  (Ref#905N) 

Manufactured 1980, double drum, blocks, 102’ x 260,000# hydraulically raised and scoped mast, mounted on 4 axle carrier, Detroit Series 60 diesel engine (2007), 5860 Allison transmission, all tooling for tubing and rods, currently working  Price:  $575,000

---

IDECO H30 DRIVE IN WORKOVER RIG (Ref#1098N) 

I

Complete crown to the ground category 4 rebuilt in August 2008, Ideco 4 axle drive in H30 double drum drawworks with new 1”drill line, Ideco 70ft 120,000# hydraulic scoped and raised derrick, New McKissick 82A 75 ton block, New 12 volt rig lighting system, Detroit diesel 50 series tier III motor (rebuilt), Alison 4460 automatic transmission (rebuilt), New Bosch Rexroth (WABCO) air valves, Air line systems, brakes and tires (new), New decking and stairways, New hydraulic system, New rig electrical system   

Price: $550,000

Completely rebuilt and meets category 4 requirements, 152 page document for Ideco.

6 months guarantee

---

Walker Neer P5000 (Ref#1616Nc) 

30" x 8" double drum draw works with air clutch's, Randolph drive, Mounted on International with 671 Detroit diesel, 65' mast raised and telescoped by hydraulic cylinders, 3 hydraulic outrigger leveling jacks.  450' of 7/8" tubing line, approx. 6,000'of 9/16" sandline, tool racks, tool boxes, Auxiliary hydraulic circuit, Sowa 50 ton 2-sheave block

PRICE:  $125,000 without tooling

PRICE:  $135,000 with tooling

---

Wichtex C65A D/D (Ref#1616Nb) 

     

7000’ capacity, T-68-100 Wichtex derrick 65’ x 100,000# cable raised and telescoped, mounted on 1981 International F570 tandem axel truck with 350 Cummins, Oilfield front bumper, Full floating 31" x 8" double drum draw works, with air friction clutches, Franks right angle drive, 3 hydraulic outrigger leveling jacks, 450' of 7/8" tubing line, approx. 6,000' of 9/16" sandline, Spooling capacities: tubing drum 3785’ of 3/16” line, 2784’ of 7/8” line, sanline reel 7725’ of 9/16” line, 6250’ of 5/8” line,  tool racks, tool boxes, Auxiliary hydraulic circuit, winch, cat head, McKissick 50 ton 2-sheave block, currently working, good condition, ready for use

PRICE:  $125,000

Tooling available at extra cost:  links, tubing elevators with inserts for 1-1/2” – 2-3/8” tuabing, Guiberson air slips, Foster 58 power tongs, no rod tools, cable tools: rope socket, stems, jars 

PRICE WITH TOOLING:  $135,000

---

SEISMIC RIGS

SEISMIC DRILL BUGGY LIQUIDATION (Ref#1326N)

(7) Seismic Drill Buggies on Ardco/Geospace/Hilyard/Carriers with 130’ drill pipe - $125,000 per unit

(7) Seismic Water Buggies on Ardco/Geospace/Hilyard carriers - $45,000 per unit

(5) Auger rigs with water tank on buggy - $40,000-$95,000

 

                               

 

---

 

TOP HEAD DRIVE RIGS

---

 

ATLAS COPCO T3W (Ref#5280N)

Year 2006, approx. 1,800 hours, 1070/350 air, mounted on 2006 Mack Granite A1400 with 58,000# rears, single rod loader and rod spinner, set up for 3-1/2” drill pipe (can convert to 4-1/2” at no extra charge)

Price: $500,000

---

DRESSER T70W   (ref#7380a) 

         

Manufactured 1982, 900/350 LeRoi 2-stage screw compressor (rebuilt 2008), Detroit 8V92T diesel engine on deck (rebuilt 1996), 70,000# pullback, Mounted on Crane Carrier with 6V92 Detroit diesel (new 2007) with Jake Brake, 3 hydraulic leveling jacks, 1 rod pipe feeder, 70,000# main winch and hoist line with 4-part line and travelling block, Rotary head swings back, Mast length 47', King tongs 4-1/2" - 6" diameter, (handles Range 2 casing), The mast base has been modified and strengthened by a certified welder.  Mast cylinders are in good shape and require no repair.   There is no casing hammer and the rig was not modified for a casing hammer.  Currently drilling.  Owner retiring, located West Coast.  Price:  190,000

Available at extra cost:

1991 Pettibone tandem axle flat bed truck with 400 Cummins diesel engine, 13 speed transmission

200’ of 4-1/2” x 25’ heavy wall drill pipe

(50) tricone carbide bits

SD12 hammer and 12-1/4”, 14”, 15” and 19” bits

 

---

INGERSOLL RAND RD20 RANGE III DRILLING RIGS  (Ref#5629Na) 

 

Two Available, New, Never Used - Delivered 2008, 0 hours, 1250/350 air compressor on deck, Cummins 755 hp deck engine, 120,000# pullback, 30,000# pulldown, 51.7’ clearance, 62’ derrick, 4000# jib crane, 120 rpm, 8000 ft/lb, 3” ID top drive x 1500 psi, 7500# casing hoist, mounted on 10 x 6 carrier, 281” WB, 90,000# GVWR  

Price for each rig:  $825,000  each delivered to Durban, South Africa port  (replacement cost 1.3 mil)

Available at extra cost:  6,000’ drill pipe, 5-1/2” and 8-5/8” casing packages, skid mounted oilfield mud tanks 7’6” x 16’, new spare set of desert floatation tires and wheels, 1 year spares

---

INGERSOLL RAND RD20-III (Ref#15621Na) 

Manufactured 2004, 17,673 hours, idle since March 11, 2009 (company went to deeper work)

Cat 3412E deck engine, HR 2.5 Series IR 1250 cfm/350 psi air compressor, Range III tower package

mounted on 5 axle carrier with 9418 miles. 

Recent repairs:  new gearbox 15,000 hours, all new hydraulic pumps and rebuit carousel 16,000 hours, replaced compressor with rebuilt compressor (16,200 hours), installed new cam in deck motor 16,500 hours, new injectors and new engine oil pump.  

Price:  $425,000                    

                                                     

---

INGERSOLL RAND RD20 –III  (Ref#2243N) 

Manufactured 2006, 13,000 hours, 1250/350 air compressor, Cummins QSK19 diesel engine on deck, mounted on 5 axle Crane Carrier with Cat C13 diesel engine, 120,000# pullback, hammer oiler, water injection,    Price:  $675,000

Also available:

2007 RD20-III   Price:  $725,000

167 drill rods - $83,000

167 drill rods - $76,000

2008 Stanton doghouse - $105,000

2007 Stanton Dynamic doghouse - $115,000

2006 Stanton Dynamic drill deck - $30,000

2007 Stanton Dynamic drill deck - $30,000

2006 Stanton Dynamic pipe trailer - $26,000

2006 Stanton Dynamic pipe trailer - $26,000

2007 Stanton Dynamic pipe trailer - $29,000

2007 Stanton  Dynamic pipe trailer - $29,000

1996 Warbird pipe trailer - $11,500

1996 Warbird pipe trailer - $11,000

1985 Transcarft pipe trailer - $9,500

1987 Transcraft pipe trailer - $9,000

2008 Stanton Dynamic steel trailer - $30,000

1995 Transcraft pipe trailer - $8,000

2009 Stanton Dynamic lowboy trailer - $33,000

Penn Detroit diesel light plant w/16’ flat deck trailer - $19,000

2007 Hurricane comp booster, 2007 Haul-a-Frame trailer for booster - $110,000

3000# R&S Machine BOP - $16,000

Kohler light plant 60 - $14,500

3000 gallon fuel tank on skid w/IR Ground Air 1170 - $130,000

2007 Stanton Dynamic trailer w/3000 gallon fuel tank, Perkins light plant, aux air compressor - $185,000

300 bbl water tank - $3,000

300 bbl water tank - $5,000

300 bbl water tank - $5,000

300 bbl water tank - $4,000

250 bbl water tank - $3,500

129 aluminum drill rods - $203,500

40 steel rods - $47,600

2 pipe racks - $2000 each

 

---

INGERSOLL RAND T4W  (Ref#5708N) 

Manufactured 2007, 1300 hours.  IR HR 2.5 1240/350 air compressor, 70,000# pullback, 755 hp Cummins QSK19 (Tier II) deck engine, mounted on Crane Carrier with Cat C13 (380 hp) engine 

Price:  $575,000

---

INGERSOLL RAND T4W  (Ref#1687N) 

                                             

Manufactured 1998, 900/350 air compressor, 50,000# pullback, 9,000 frame hours, Cummins QSK19 deck engine (rebuilt 4500 hours ago), worm gear head, 18 gpm Bean pump, 7 gpm oiler, 7/4 rod carousel, mounted on Crane Carrier with Cummins L10, Jake brake, locking rear, 15,000 miles, 280’ drill pipe and tools, rig to be painted and is well maintained and ready for work  Price:  $250,000

 

---

PORTADRILL TLS-423 TOP HEAD RIG  (Ref#3060N) 

 

Double drum hoist, 51’ x 60,000# pullback, 48’6” clear height to run R-3 casing, hydraulically raised mast, 2-sheave blocks, Detroit 8V71 diesel engine on deck, Sullair 750/350 rotry screw air compressor, 10” rotary table, breakout tong and Bean mist pump, top head drive, hydraulic boom, mounted on 1992 Autocar 4-axle carier with tandem steer, sleeper, Jake brake. 

6” x 8’4” x 4’ L folding mud boat ramp. 

7’6” x 18’9” driller’s house, 4-compartment lubester and 7’5”W x 8’H x 10’L 4400 gal fuel tank.

Single axle pipe float with 1400’ of 3-1/2” x 20’ drill pipe

Price:  $210,000

---

SCHRAMM TXD TOP HEAD DRILL RIG  (Ref#3909N) 

                 

Manufactured 2008, 50’ top head travel telescoping mast, 200,000# pullback, 32,000# pulldown, Detroit 12V-2000TA 760 bhp engine, mounted on 3 axle trailer with 4 outriggers.  Trailer mounted load safe pipe handling system.  Currently drilling     7,979 hours

Price:  $900,000

 

---

SCHRAMM T685H DRILL RIG PACKAGE (Ref#4555N) 

Manufactured 1986, 900/350 air compressor, Detroit 12V71 deck engine (1200 hours), 70,000# deephole package, mounted on International 5000 truck with Cummins engine

1977 GMC 7500 4-door crew truck, water and fuel tanks, pipe truck,

1170/350 IR compressor, manufactured 2005, 2034 hours  with C15 Cat engine on wheels in whisperized house

Doghouse, tools, 1860’ drill pipe, bits, hammers, generator, tools,

Package Price:  $455,000  PRICE REDUCED:  $330,000

---

SCHRAMM T685WS  (Ref#2368Na) 

Manufactured 1999, 6300 hours, Sullair 1360/350 air compressor (can go to 500 psi), MTU 12V 2000 TA 760hp deck engine (3113hours), 74,700# pullback, 2 drill pipe carousels, rod rack, 7600# winch, auxiliary winch, 25 gpm hammer oiler, walkways on side of rig, mounted on 1999 Navistar 2674 International truck with Cummins M11 400hp engine, Jake brakes, 14,300 miles, 60% rear tires, 90% front tires,

 

Price rig only:  $340,000  Reduced Price for rig only $275,000

 

1,450’ of 4” x 25’ x 2-3/8 IF drill pipe available at extra cost.

 

---

speedstar Star Drill S15K-HL (Ref#12701N) 

Manufactured 2001

450/200 Sullair air compressor, GEFCO 4x5 mud pump,

50,000# torque, 10,000# pulldown and 20,000# force up,

(pipe rack carries 18 pieces of 3-1/2” x 20’ drill pipe (removed from rig), 10 pod carousel for 2-7/8” x 20’ flush joint drill pipe,

mounted on  2002 Peterbilt 3300 truck with 3126 diesel engine (300hp), 16000# front axle, 40,000# tandem rear axle,

Fuller RTO11908 10 speed transmission, dual 60 gallon fuel tanks, PTO drive. 

Price:  $210,000    PRICE REDUCED  $125,000

---

 

SPEEDSTAR 185K (Ref #6330N)

 

 

8000' depth capacity

Manufactured 2005, 8035 hours,

Mounted on 5 axle carrier with Cat C15 engine (engine rebuilt at 6300 hours)  18 sp transmission with engine brake,

185,000# pullback, 30,000# pulldown, rotation speeds 0 – 53 rpm high torque and 0 – 106 rpm low torque, maximum torque 140,000 in/lbs,  

62’5” length of mast, 51’ working height, 17 gal hammer oil tank,

7000’ racking board, lights, catwalks, ladder, tongs from 2-3/8 OD to 10-3/4OD,

40 gal/min at 1000 psi Myers pump, 2 auxiliary winches, gross weight 100,580 lbs. sub-base 

 

PRICE: $ 950,000

 

             

---

SUPPORT EQUIPMENT

---

 

BOWEN 3.5 POWER SWIVEL (NEW, NEVER USED)  (ref#9921) 

     

Powered by C7 Cat engine, mounted on new oilfield skid, hydraulic hose reels, 120 ton hook/load capacity, 100’ 4-wire pressure hose, 100’ 2-wire return hose, remote control air powered w/100’ hydraulic and air line, Sunstrand hydrauulic system, high pressure loop filter suction strainer, 10 micron return, 90 gallon hydraulic tank, 90 gallon fuel tank, 12V battery and battery box, swivel rack with hydraulic winch, elevator bail, manufactured from all new U.S. components with 1 year guarantee, Dimensions 234” long x 90” wide x 90” high – 13,500 lbs        Price:  $150,000

Optional 3-axle trailer trailer (similar to trailer made by National):  $5,000

---

BOWEN 2.5 POWER SWIVEL  (NEW, NEVER USED)  (Ref#9922) 

       

New and Unused - Immediate Delivery

Mounted on skid, Cat 4.4 diesel engine, Sundstrand hydraulic system, 85 ton hook load capacity, power reels with 100’ 4-wire pressure hose, 100’ 2-wire return hose, remote control air panel w/100’ hydraulic and air line, Sunstrand hydraulic system, high pressure loop filter suction strainer, 12V battery and battery box, swivel rack with hydraulic winch, elevator bail, hydraulic winch, 90 gallon fuel tank, 50 gallon hydraulic tank, high pressure filter and return filters, new, manufactured from all new U.S. components with 1 year guarantee on package, manufacturer's guarantee on components

Mounted on 3 axle gooseneck trailer     

Price:  $105,000    

IMMEDIATELY AVAILABLE    (price includes delivery to Houston Port)

 

---