OILFIELD DRILLING RIGS FOR SALE

DRAGON XJ450 DRILLING RIG (Ref#5036N)

CARRIER / DRILLING RIG

XJ 450 drilling rig with single drum: Benz wide wheel base chassis 226 total miles, equipped with 2 single front axles and 3 rear dual axles, front tires 445/65 R22.5 20pr (L) 90% remaining, 12R 22.5 rear tires- 90% remaining.

Booster: New 2009 Peerless tandem axle, self-steer booster, 275/70R 22.5 (H) tires- 100% remaining

Drawworks: Single drum 1” lebus groove w/ ADT-324H air thrust disk clutch on main drum, splash cooled brake, 700gl antifreeze tank

Prime Power: CAT C-15 475hp @2100rpm meeting tier III emission standard w/ Allison S5610HR transmission

Auxillary Brake: Model:  22” SR Hydromatic Brake w/ 528 gal. cooling tank mounted to carrier

ROTARY

Rotary Drive: Splash lubricated ADT-218H shaft driven clutch w/ 5 forward and 5 reverse, completed with anti-reverse

Rotary Table: 17.5” Table

MAST

Derrick/Mast: 110’.8” two section telescoping mast rated @303,000 carrier mounted.  Board capacity 8000’ w/4” drill pipe.  Electric D.C. & Pipe Mule.  Class II inspection and certification completed on 4/09/2010

Crown: Box type w/4 cast steel sheaves.  Rope grooved to adapt to API 8C relative standards.  Equipped with handrail

TRAVELING SYSTEM/SWIVEL/KELLY

Block:  150 ton

Swivel: 120 ton #5000 PSI

Kelly: 1- 38'x 5 1/4"" hex w/ Drive bushing-V. Good condition

MUD SYSTEM

Mud Pits: Two (2) 225bbl mud tanks w/ 2- 6x8x11 centrifugal pumps powered by 2- 50hp. Electric motors. 1- 4x8 single shale shaker, 1- Mud hopper mounted on top of suction pit. 30 bbl pre-mix pit built into suction.

SUBSTRUCTURE

Model DZ137-3.7-S, Rated 330,000#, 15' split telescoping w/11'7" clearance under rotary beams, Floor 16.5'x14' w/ V-Door. Working floor is covered w/ 1.25" thick yellow safety traction mats.

CATWALKS

2 (two) 27' L x 4'W

PIPE RACKS

3 (three) sets

WINCHES

Hydraulic - winch w/ 9/16" cable and tail chain

Air Hoist - winch w/ 9/16" cable and tail chain

GENERATOR HOUSE

Generator/Electrical/Air Compressor –

1 - 380 KW/60Hz Marathon Generator w/ Series 60 Teir III Detroit Diesel enclosed in 8'x 30' house. 1- Sullivan 25hp/200psi Screw type air compressor. Electrical system control panels w/ outside electrical connections

Lighting –  Complete rig and interior building lighting systems, combination florescent and  mercury vapor, laid out in a standard industry configuration.

WATERTANK

250bbl water tank w/ 2- 3x4 washdown pumps enclosed in one end and 4 station Koomey accumulator system and Landa power washer in the other end

TOP DOGHOUSE

8'x12' Top doghouse that retracts into water tank for mobilization. Equiped w/ benches and knowledge box.

ANNULAR BOP

#3000 Regan positive close, relax open 9" annular BOP, trailer mounted

MUD PUMPS

Pump #1: WorkForce 660 (PZ-8 Specs.) Tri-plex pump w/ charge pump, 1659 total hours. Powered w/ Detroit Series 60 Teir III Diesel engine. All components skidded on 1 master skid. Exchange transmission w/ 500 hours

Pump #2: WorkForce 660 (PZ-8 Specs.) Tri-plex pump w/ charge pump, 1537 total hours. Powered w/ Detroit Series 60 Teir III Diesel engine. All components skidded on 1 master skid. Exchange transmission w/500hrs.

CHANGEHOUSE/PARTS ROOM

Bottom Doghouse: House is 8'x40'. Half is divided into 8'x20' Change house and includes lockers and shelves for appliances

Parts House: House is 8'x40'. Half is divided into 8'x20' parts house and includes work bench with grinder and vise, Shelving is enclosed with expanded metal doors  for parts.

FUEL TANK

1- 6500 gal. fuel tank w/ pressured system setup and 120v electric

DRILL PIPE

- NEW 90 jts. S-135 New #14.4 lb./ft w/  4" Full hole conn.  App. 2835'

- 200 jts used G-105  #14.4 lb/ft w/ 4"Full hole conn. Inspected  08/2008 App. 6300'

DRILL COLLARS

- 20 (twenty) 6 1/4" x 2 1/4" D.C w/ slip recess  4 1/2 XH box to 4 1/2 XH pin. Inspected 8/2008

- 1 ea. 6 1/4"x 2 1/4 " bottom hole D.C. w/ slip recess. 4 1/2"XH box to 4 1/2" Reg. box, Inspected 8/2008

Price: $2,600,000

NATIONAL T-20 (Ref#5103N)

Rig assembled and put into service in 2008

 DRAWWORKS:

National T-20 single drum, Lebus grooved Parkersburg 22” double hydromatic brake, single engine compound, p/b Cat C-13 diesel engine (400hp) w/electric start, radiator, gauges, Oilworks C-105-125 torque converter, and Foster catheads.  (drawworks reconditioned w/new bearings, clutches, brake bands, brake blocks, chains, brake flanges & linkage, new engine and torque converter in 2008). Mast and drawworks mounted on factory made tandem axle trailer. Mast & trailer rebuilt in 2008

MAST:

Lee C Moore Trailer Mounted 97'H X 300,000# GNC (210,000# static hook load).  FREESTANDING scoping mast w/DERRICK racking  board

SUBSTRUCTURE:

10'H "T" type w/back on ramp, rotary beams, & stairs, (2) 8'W x 28'L rig mats, 8'W x 30'L rig mat, (2) 8'W x 40'L rig mat

GENERATORS/UTILITY HOUSE:

Murphy 360KW generator: p/b Cat 3412 diesel engine, electric starter, radiator, gauges. Skid mounted.  Air compressors: Ingersoll-Rand & Champion p/b electric motors.  Mounted in 10'W x 40" utility house with transformer & electrical controls.  (Murphy generator has less than 9 mos. Use since rebuild)

BBC 250KW generator p/b Cat 3408B diesel engine, w/electric start, radiator, gauges.

MUD PUMPS:

(1) Mudder MD-9, (GD PZ-9 design)  triplex mud pump w/forged steel fluid end, Mudder pulsation dampener, 5" x 6" centrifugal charging pump, p/b Cat C27 (880hp) diesel engine, w/ air start, radiator, gauges, Prep model HC transmission, mounted on skidded pump house. (Pump has been re-bearinged with American bearings & both pump and engine were new in 2008)

(1) Oilwell 218P duplex , API-8 forged steel fluid end, w/quick change caps, pulsation dampener, type D mud gauge p/b Cat D-353  (330hp) diesel engine w/air start, radiator, gauges, drive assembly, skidded and mounted on covered skid.

ROTATING/TRAVELING EQUIPMENT:

IDECO 20 ½” x 44" rotary table w/split master bushing.

4 ¼” x 35'L square kelly

National-Ideal Type F 150 ton Swivel w/Varco drive bushing

Upper and lower kelly valves

McKissick (4) sheave 150 ton block/hook combination w/BJ Unimatic 6150 hook                                                          (2) 2 ¼”x72”elevator links

BOP/WELL CONTROL EQUIPMENT:

Shaffer type E 11" 3000# double gate

Myers 3 station closing unit w/120 gallon hydraulic tank, (8) accumulators, air operated hydraulic pump, triplex hydraulic pump p/b electric motor, mounted in generator house (New in 2008)

Remote closing unit mounted in doghouse (New in 2008)

3000 psi choke manifold w/4-way cross, 3 1/8" gate valve, (3) 2 1/16" gate valves, (2) adjustable chokes, skidded (New in 2008)

MUD SYSTEM:

550  Barrel capacity-2 tank

Tank #1: 6'H x 8'W x 50'L mud shaker tank w/8'W x 5' pump room, SPD 5" x 6" centrifugal pump p/b 50HP electric motor, (4) compartments, top-mounted walkways, chemical hopper with internal plumbing, Brandt style linear motion shale shaker p/b (2) Virmac vibrator motors, 2-cone desander, 8-cone desilter, skidded.  (shale shaker, centrifugal pumps & motor new in 2008.  Desander & desilter rebuilt w/ new cones, tank rebuilt w/new walkways, and internal plumbing)

Tank #2: 6'H x 8'W x 22'L mud suction tank w/6'L hopper room, MCM 5" x 6" centrifugal pump p/b electric motor, (3) compartments, (38 bbl pill tank) top mounted walkways, internal plumbing                                                                                

(tank reconditioned 2008 w/new gates, internal plumbing, walkways & stairs)

RIG HOUSES:

8'W x 26'L top doghouse w/ knowledge box, bench storage, and lockers

Alta Fab 12'W x 38'L tool pusher’s house w/kitchen, living area, (1) bedroom, office, fully furnished, and skidded, Rebuilt in 2008

WATER/FUEL TANKS:

8'H x 8'W x 38'L 430 BBL capacity water tank w/14'L pump room/parts room.  Mission Magnum 3" x 4" & 2" x 3" circulating pumps, each p/b 20HP electric motor, Cat triplex pressure washer.

8'H x 22'L 8000 gallon fuel tank w/ (2) explosion proof fuel pumps, each p/b 5HP electric motors.

5 compartment oil bunker

HANDLING TOOLS:

(2) type B rotary tongs w/complete set of tong heads

Raugh Mfg  air/hydraulic pipe spinner

(1)WTM 4 1/2" drill pipe elevators

(1)Varco 4 ½”drill pipe slips

(1)Varco 6”drill collar slips

(1)Varco 8” drill collar slips

(9) drill collar lift subs 4 1/2” XH

(2) drill collar lift subs 6 5/8” Reg

(4) assorted X.O. subs

Ingersoll-Rand air hoist

AUXILLARY EQUIPMENT:

Martin Decker Clipper-type weight indicator

3 1/2"ID X 60’ rotary hose, 5000# rated

9', 12', & 15' X 3 ½”ID vibrator hoses, 5000# rated

5'W x 40"H x40'L catwalk w/V-door

(4) 8'W x 36'L pipe baskets

Five Star hydraulic/electric wireline measuring device New in 2008

Vapor proof rig lighting New in 2008

Approx. 3000' 1" drill line

Assorted hand tools, rig parts, spares, and fire extinguishers necessary for drilling operations

DRILL PIPE & COLLARS:

4929' (158 JOINTS) 4 1/2" X 16.60#, Range 2 Grade E drill pipe w/4 1/2" XH tool joints,

 (10) 6" to 6 1/4"OD x 2 1/4"ID x 30'L drill collars New in 2008

(2) 8"OD x 2 13/16 id approx. 30'L spiral drill collars   

 (2) sets of (4) triangular pipe racks

Price: $900,000

IDECO H-35 (600HP) (Ref#5104N)

TYPE: SKID MOUNTED DRILLING RIG

DRAWWORKS

IDECO H-35 HYDRAIR Single drum Drawworks; LEBUS Grooved f/1-1/8” Line, Makeup & Breakup Catheads, Air Driller’s Console Controls w/ Engine Shed.

COMPOUND

IDECO 2-Engine, In-Line Compound w/ Quincy 325C 2-Stage Air Compressor

BRAKE

PARMAC 15” DR Double Hydromatic Brake Drawworks Mounted

ENGINES

(2) CAT 3406 Diesel Engines, (1) w/ Air Starter & (1) Electric Motor Starter, Each w/ NATIONAL C-195-64-FH Torque Converter, Air Clutches, Each Skidded & 300 HP

MAST

Lee C. Moore, 127’H x 15’W Cantilever Mast 340,000 SHL, Pin-Type, 4-Sheave Crown (Includes Fastline), 1^1/8” Line, Crown Safety Platform, Racking Board, Pipe Boom, Tong Counterweights, Derrick Climber, Ladder, Deadline Anchor, 4” Standpipe, Standpipe Manifold 2/4” & 2” Gate Valves, Type D 3000# Pressure Gauge & Mast Stand

SUBSTRUCTURE

10’H x 18’6”W x 40’L Box-on-Box Substructure 400,000# SHL, w/ V-Door, Stairs, Safety Rails, w/ Drop in Floor Plates

PUMPS

National K500A Duplex Mud Pump; 500-HP, 7^1/4” x 15”, Forged Steel Fluid End w/ Quick- Change Valve & Cylinder Head Caps, CONTINENTAL-EMSCO Pulsation Dampener, OTECO 2” Shear Relief Valve, Drive Assembly, Master Skidded, Powered By CAT 3412 Diesel Engine w/ Air Starter, Air Clutch & Skidded.

IDECO MM-600 Duplex Mud Pump; 600-HP, MATCO Forged Steel Fluid End w/ Quick-Change Valve & Cylinder Head Caps, HYDRIL K-20 3000# Pulsation Dampener, OTECO 2” Shear Relief Valve, Type D 3000# Pressure Gauge, Drive Assembly, Master Skid, p/b CAT 379 Diesel Engine w/ Air Starter, Air Clutch, Skidded Belt Drive Package;

ROTATING EQUIPMENT

IDECO 175-F Rotary Table, 17^1/2” x 44”, w/ Split Master Bushing

GRAY 185-Ton Rotary Swivel

4^1/4” x 41’L Square Kelly w/ BAASH-ROSS Kelly Drive Bushing, Square Drive in Rat Hole Sock.

TRAVELING EQUIPMENT

IDECO UTB160 Shorty 160-Ton Block/Hook Combination, 4-Sheave

2^1/2” x 96” Elevator Links

WELL CONTROL EQUIPMENT

PAYNE 3-Station Closing Unit (NOTE: Mounted on Parts House Skid).

CAMERON 5000# Choke Manifold w/ (6) 2” Gate Valves, Adjustable Choke & Skidded

RIG HOUSES

6’11”W x 23’8”L Doghouse w/ Round Top, Knowledge Box, Lockers, Bench Storage, Cabinets, Fluorescent Lights & Heater.

8’W x 18’L Parts House (Bottom House) w/ Flat Top, Parts Bins, Fluorescent Lights, Air Compressor p/b 15HP Electric Motor & Skidded.

8’W x 21’L Change House w/ V-Top, 4’ Porch Extension, Lockers, Bench Storage & Cabinets.

GENERATORS / UTILITY HOUSE

CAT SR-4 155 KW AC Generator p/b CAT 3306PC Diesel Engine w/ Electric Starter & Skidded.

CAT SR-4 135 KW AC Generator p/b CAT 3304 Diesel Engine w/ Electric Starter Skidded.

QUINCY 325C Air Compressor p/b 5 HP Electric Motor

All Above Mounted in 8’W x 15’L Utility House w/ V-Top, 13’L w/ Fluorescent Lights, Skidded w/ Fuel Tank & Lubster

MUD SYSTEM

5’H x 11’7”W x 34’6”L 356-Barrel Mud Tank w/ (2) Compartments, 10’L Covered Porch w/ MISSION 5” x 6” Centrifugal Pump p/b 50 HP Electric Motor, Mud Hopper, Top-Mounted Walkways, Stairs, Safety rails, Skidded Complete w/ (2) Deck Shale Shakers.

6’H x 8’W x 12’L 120-Barrel Premix Tank, Single Compartment, Flat Bottom w/ 12’L Covered Porch Extension, (2) Mud Hoppers & Skidded.

WATER / FUEL TANKS

6’H x 8’W x 38’L 325-Barrel Water Tank

18’L Oval-shaped Fuel Tank, Skidded & Mounted w/ Generator House & Lubster

3’2”H x 2’10”W x 8’8”L 3-Compartment Lubster, Mounted on Skid w/ Generator House & Fuel Tank

HANDLING TOOLS

WOOLLEY Type B Tongs w/ Heads

BJ 4-1/2” Center latch Drill Pipe elevator

Mud Saver Bucket

GARDNER-DENVER HK-1 Air Hoist

AUXILIARY EQUIPMENT

GH BEAR Automatic Driller

GEOLOGRAPH Single-Pen Recorder

MARTIN-DECKER Clipper 360,000Lb. Capacity Weight Indicator

Tong Line Pull Gauge

3^1/2” x 55’ Rotary Hose

34”H x 8’W x 36’L Pipe Tub w/ 40”W Steel Deck Catwalk w/ 10’ Extension & Steps

(3) 30”H x 7’W x 40’L Pipe Tubs,

Electric / Hydraulic Wireline Measuring Device

Rathole & Mousehole

Fluorescent & Mercury-Vapor Rig Lights w/ Wiring

Drill Line Spool & Stand

PIPE RACKS

2 Sets (4) 42”H x 28’L Triangular Pipe Racks

Price: $1,950,000