SUN MACHINERY CORP
Telephone: (516) 536 7375 Fax: (516) 536 7317
These rigs are located at various locations through out the USA and Internationally.
e-mail: rigs@sunmachinery.com
Spencer Harris, Continental Emsco
Trailer Mounted Single Drum Drilling Rig (Ref#3663N)
Model f/11/8” Line, Catheads, Air Clutches,
15” Triple Auxiliary Water Brake, p/b (2) Caterpillar 3406 Diesel Engine w/Electric Starter,
Radiator, Twin Disc Torque Converter
2 Engine Compound, Air Compressor,
Spencer Harris 97”H 250,000# Static Hook Load Tubular Mast,
Hydraulically Raised & Cable Scoped,
All Mounted on 3 Axle Trailer, w/Hydraulic Utility Winch, Folding Walkways, w/Stairs, Fuel, Air, Water & Hydraulic Tanks, Work Platform, 10.00R20 Tires, Weight Indicator, Torque Indicator
SUBSTRUCTURE 12’H X 14’W X 35’L Box Type Substructure Rotary Beams, V Door Ramp, Stairs Safety Rails, 6’ H Back On Ramp.
MUD PUMPS ((2) Continental Emsco F 650 triplex pumps, powered by Caterpillar 379 Diesel Engines, Skidded, Forge steel fluid ends w/treated caps, pulsation dampers, 2” shear relief valves, type D pressure gauge, V belts w/guards, serial # 4 and 20
GENERATORS (2) 3406C, 320KW CAT SR4 generators, w/Electric Starter, Radiators, Gauges, Control Panel, mounted, 75 Kw single phase transfer mounted on 8ft x 32ft Heavy Float Trailer, w/Rails, Catwalk, 5hp Shop Air Compressor, Dog House, Stairs, etc.
Hydraulic POWER UNIT 1 CAT 3054 Hydraulic Power Unit with Quick release Hydraulic Hose connections and 30 gallon reservoir.
TWO PIT MUD SYSTEM 5’h x 7’10” x 30’l Mud Suction Tank w/double Compartment, Flat Bottom, Internal Plumbing, Mud Agitator, Side Mounted Walkways, Stairs, Safety Rails, Skidded
5’ X 7’10 X 30’L Mud Shaker Tank w/(3) Compartments, Flat Bottom, Internal Plumbing, Side Mounted Walkways, Stairs, Safety Rails, Skidded
Mud Hopper w/Harrisburg 5” X 6” Centrifugal Pump, p/b 50 HP Electric Motor, Skidded
Halco 5” X 6” Centrifugal Pump, p/b 50 HP Electric Motor, Skidded
Brandt Mini Cobra Double Screen Shale Shaker
Brandt 4 Cone Desilter
SWACO Single Cone Desander
ROTATING AND TRAVELY EQUIPMENT
Brewster 18” X 44” Rotary table w/Split Master Bushing
Ideal 150 Ton Block/Hook Combination with/4 Sheaves 1 1/8 line
SWIVEL Brewster 6SX 220 ton Swivel
RIG HOUSES Parts House, 8ft x 15ft, Rounded Top, Skidded
WATER/FUEL TANKS Fuel tank, 7,700gal horizontal 8’X 20’.6” with Centrifugal Positive Pressure Pump and Black Iron Fuel Lines
500 BBL Water Tank / mobile Frac Tank
AUXILLIARY EQUIPMENT
MARTIN – DECKER Clipper 0 – 360,000# Weight Indicator
Wire Line Unit, Electrically Controlled
4’ID X Approx. 50’L Rotary Hose, 5000 psi
2 (2) 8”ID X 5”L Suction Hose/Vibrator hoses
4’H X 8”W X 30’L Junk Box, Skidded
Florescent Rig Lights w/Wiring
Approx. 1000’ of 1 1/8” Drill Line w/Spool, Stand
Koomey 3 Station Closing Unit, S/N 10956, w/(4) 10 Gallon Accumulators, (2) Air-
Operated Hydraulic Pumps, Stainless Steel Flexline, mounted on Doghouse Porch
4 ¼” X 37’ Square Kelly and Square Kelley Bushing
BJ Type B and Wooley Rotary Tongs
Cam Tech SSW 30 hydraulic pipe spinner
DRILL PIPE AND COLLAR
16 – 6” Slick Drill Collar
5,363 ft. of mixed grade and Quality 4” 14.0# F.H. approximately 2,637 ft DWB, total of
8,000 feet all hard banded
CLEANED AND PAINTED
PRICE: $2,400,000
SPENCER HARIS 7000 (Ref#4208N)
Brewster N4 drawworks modified with 15” Hydromatic brake, 2 axle compound
97’ x 250,000# Spencer Harris telescoping mast
Mounted on 3 axle float
Skytop Brewster 150 ton block and hook 4 sheave
(2) Detroit 8V71 diesel engines
Substructure: 19’ Wide x 12’ Long, ramp 40’ x 8’4” – 44” high
18” x 44” Brewster rotary table with split master bushing
4-1/4” x 36 hex kelly, kelly bushing, kelly shuck, mousehold shuck
(1) Great American GA 750 mud pump with 379 Cat enigne
(1) Great American GA 550 mud pump with D379 Cat engine
Two mud tanks with mud hopper, desander, desilter, and all plumbing and shale shaker
18” catwalk 8 x 40 and V Door
Junk box and wire line unit
Doghouse mounted 300 bbl water tank
(13) drill collars
7500’ 4” drill pipe
225 kw generator p/b Cat 3406
Gardner Denver air compressor
Subs and handling tools
Choke manifold, 10,000 gal fuel tank, 11” 3K Reagan BOP, BOP closing unit,
Kelly chuck, mousehole shuck, lubester skid/junkbox skid, set drill pipe slips, drill collar slips, set 9’ elevator links, (6) drill collar , set pipe racks, set BJ type C manual tongs, lifting subs,
Price: $750,000
SPENCER HARRIS 6000 (Ref#1134N) Manufactured 1969, single drum, air clutches, mounted on 3-axle truck, 17-1/2” rotary table, kelly, swivel, hook/block, 8V92 Detroit diesel, 103’ x 250,000# hydraulically raised and cable scoped mast, fold down work platform, located Mexico Price: $465,000
SPENCER HARRIS 3500 (Ref#15523) Manufactured 1971, double drum 7/8” line, air clutch, high/low drum, 100’ x 150,000# hydraulically raised and scoped mast, mounted on all-wheel drive Oshkosh 2-axle rear truck, powered by Cummins 235 diesel engine, PTO drive for rig, cathead Price: $250,000
Available: 100 ton block and hook w/bales, swivel, substructure, 26-1/2” rotary table, kelly and kelly bushing, elevator, kelly hose, 4’ back up ramp, located South Pacific Package Price: $350,000
EMSCO GA500 (Ref#15718)
Drawworks:
GA 500 Emsco 1,000 HP two-engine compound complete with air clutches, control panel and Parkersburg hydromantic brake and air compressor.
Drawworks Power:
For Drawworks, two 460HP each Cat D-3406 Type B diesel engine with Twin-Disc Torque Converters.
Lee C. Moore, 115 ft x 13 ft base pin type cantilever, GN hook load 380,000 lbb., with 5 sheave crown block, 1-1/8” grooving, deadline anchor and stand pipe manifold. Substructure 10 ft. high x 18’ wide x 40’ long with V-door, catwalk, pipe racks, band rails, set back pipe rack, v-door slide and air hoist mounted on rig floor.
Mud pumps:
1 each Ideco 700 duplex mud pump (rebuilt 1 year ago) complete with forged steel mud end, pressure gauge, pulsation dampener and 2” shear relief valve.
1 each National C-250 duplex mud pumps complete with forged steel mud end, pressure gauge, pulsation dampener and 2” shear relief valves.
Mud pump power:
One 650 HP Cat D-3412 diesel engine – rebuilt.
One 460 HP Cat D-3406 Type B diesel engines – rebuilt.
Generators:
Each generator powered by Cat D-3306 diesel engines.
One engine, recently rebuilt. All wiring in like new condition.
Mud pits:
Three each steel pits 600-barrel capacity system, complete with walkways, mud guns, double screen shale shaker (450 gpm), two-cone de-sander and dump gates. Skid mounted. In like new condition, used very little and only when drilling conditions required it. One shale shaker and mud mixing system for earth pits operation, when steel pits not needed or in use.
Block/Hook:
Block 200 ton with four 36” sheaves grooved for 1-1/8” drilling line.
Hook 150 ton Skytop Brewster.
Rotary table:
Rebuilt 17 ½” Emsco rotary table, complete with sprocket and drive chain.
Blowout preventer:
One Hydril 5000-psi annular complete with wellhead flanges, flowline and chock valves and two each rotating heads.
Accumulator:
Four-station hydraulic unit complete with accumulator bottles, air motor, triplex pump, piping and connections.
Upper and Lower Doghouses:
8” wide x 40’ long with change room and parts compartment.
Upper doghouse mounted on top of 400 bbl. water tank.
Kelly and Kelly Bushing:
4 ¼” square Kelly with 6-5/8” left hand reg. sub.
Kelly bushings for square 4 ¼” kelly with rollers.
Drill pipe and drill collars:
8000 ft grade E 4 ½” premium drill pipe.
20 each 6 ¼”, inspected and two each 8” spiral drill collars.
Instrumentation and handling tools:
Complete compliment of instruments and tools to fulfill all needs of a drilling rig to drill and complete 10,000 ft wells.
Currently stacked.
Price: $4,400,000
CONTINENTAL EMSCO GC500 (Ref#4426N) New or Rebuilt, Drawworks Continental l Emsco GC 500 with double 22 Parmac Brake with 2 engine compound with 320 Quincy Air Compressor Drawworks powered by two C15 Cat Engines with Twin Disc Torque converters 2 Hydraulic Cat Heads 2 Hydraulic Handling Winches, Derrick Lee C Moore 131’, Sub Base 45L X 14H X 24W Lee C Moore. Block: McKissick 4 sheave 1 1/8 groove, Shorty combo Hook. Swivel: 200 ton Grey. Kelly: 5 X 42 Hex with Bash Ross Roller Bushing. Rotary Table Emsco. Tongs: Type B BJ
Mud Pump (1) F1000 Triplex with 5 X 6 Mission Charge Pump Powered by Cat 3412 E with Allison 8000 Series 6 Speed Automatic Transmission.
Mud Pump: (2) F-1000 Triplex with 5 X 6 Mission charge Pump bowered by 398 Cat
Water Tank: 10W X 40L X 8H 600 BBL
Generator House: 10W X 40 X 8H with 2-400KW Generators powered by C 15 Cats, 1- Electric Powered Auxiliary Air compressor
Parts Room: 8 X 10
B.O.P. Equipment: 5 Station Closing Unit 5000 PSI Pipe and Blind Rams 3000 PSI Annular B.O.P 5000PSI Choke Manifold.
Pit System: 38L X 11 6 W X 6 H Suction Pit 470 BBLS (1) 30 L X 11 6 W X 6 H Shale Pit 470 BBLS Total Pit System 940 BBL with 2 5 X 6 Mission, Electric Powered Centrifugals. (3) Electric Pit Agitators. (2) Linear Shale Shakers (2) Cone De-Sanders (2)
Price: $3,700,000
Emsco S-45 (Ref#151Nc) Engine: Detroit 12.7 liter 60 Series 450 HP, Depth capacity: 5500’, Pumps: National K-380, Detroit 12.7 liter 60 series 450 HP, Premix Tank: MCM 5” x 6” 50 HP Electric w/85 bbl. Tank, Derrick or Mast: 97’ Lee C Moore – 250,000#, Substructure: 40’ x 14’ x 5’, Rotary Drive: Oil Well 17 ½”, Drill Pipe: Size 4 ½” inches and 5,500 feet (16.60# x-hole thread), Drill Collars: 18 ea. – 6” OD x 2 ¼” x 30’ (x-hole thread), Generator: 180 KW Koehler w/6.8 liter John Deere, Water Tank: 300 bbl. , good condition, ready for use. Price: $550,000
CONTINENTAL EMSCO WF-1 DRILLING RIG (Ref#413N)
Drawworks – Continental Emsco WS-1 600 H.P. double drum, 3 speed transmission with reverse, 2 engine compound powered by (2) M-11 Cummins 310 H.P. (each) engines with twin disc torque converters, main drum grooved for 1-1/8” drlg. Line, drawworks, mounted on tandem axle trailer with wings and handrails.
Derrick – 127’ x 300,000# Continental Emsco with racking board, stand pipe and rotary hose (rotary hose new) Derrick telescopes for moves and is mounted on tandem axle trailer with racking board, wings and handrails
Rotary table – Brewster model “O.B.18” table with split master bushings
Light plant – 100 K.W powered by 671 Detroit diesel, mounted in 8’ x 30’ house on same skid with 2,500 al fuel tank with 4 oil bunkers, also in light plant house screw air compressor powered by elec motor and 2” cent. water pump powered by electric motor
Traveling block – 150 ton, 4 sheave, grooved for 1-1/8” drlg. Line, Chinese built
Drlg. Line – 2,000 of 1-1/8” drlg. Line (new)
Swivel – Ideco 120 ton Tru-line (rebuilt with papers)
Water tank – 7’ x 10’ x 35’
Dog house – 44 x 6’ x 40’ square tubing const. with V-door ramp
4 pipe baskets
Approx. 7,400’ of 4” drill pipe – ½ string with 4-1/2” x H connection and ½ with 4” full hole connection
(12) 6” drill collars with 4” H90 connection
4-1/4” x 40’ Kelly with kelly driver and rate hole shuck
2 Type B Webb Wilson tongs (rebuilt) with spare heads, 4-3/4” & 10-3/4”
Change over subs and pick up subs needed for drilling.
Slips and elevator for 4” drill pipe and 8-5/8” csng and 6” drill collars
Halliburton wire line machine with electric motor
Air tugger
Ideco 550 duplex mud pump powered by 671 Detroit diesel twins
D-300 Continental Emsco duplex mud pump powered by 671 Detroit diesel twins, pump in pump house, new expendibles in fluid end
3 pit jets
(1) 15’ vibrating hose (new)
(1) 12’ vibrating hose
(1) 10’ vibrating hose
Spare 55’ kelly hose
Rig equipped with drilling beam and 2 piece ramp, also spare sub if you wanted to ramp rig up another 5 feet.
4’6” x 10’ x 35’ tank needs bottom but would make a nice mud tank
Rig is fully equipped and ready to go to the field.
Price: $625,000