SUN MACHINERY CORP

Telephone: (516) 536 7375 Fax: (516) 536 7317

These rigs are located at various locations through out the USA and Internationally.

Ideco

IDECO SUPER 711 (Ref#15730) Drawworks Super 7-11, Cathead, Rotary drive and airflex clutch CB-500, Lee C. Moore 1,000,000# capacity x 142’ high, 21’ leg spread, Substructure box on box, Located Colombia Price: $1,400,000

IDECO H2500 (Ref#9802) Depth capacity 23,000’ (7000 meters) with 5” drill pipe,

Ideco H2500 drawworks with Elmagco 7838 brake, (3) Cat D398 diesels with compound

Ideco SBS 143-650-30 full view mast 143’ x 750,000# with 12 lines, 710,000# with 10 lines, 20,000’ of 5” DP racking capacity

Demag hydraulic operated stabbing platform

4” OD x 5000 psi standpipe

4” ID x 5000 psi rotary hose

CCD 480 Crown Block 480 ton rated capacity, 7 sheaves: (1) 60”, (6) 55” for 1-3/8” wireline

Substructure 23’2” floor height, 705,000# casing capacity, 510,000# simultaneous cap of setback

Engine substructure to accommodate drawworks and 3 diesel engines with compound 9-1/2’ height

Ideco TBA 480-6-55 traveling block 480 ton, 6 sheaves, 55” x 1-3/8” wireline

Ideco SBS HK-480 hook, 480 ton

Ideco SBS TL 500 swivel, 500 ton

This package of components is available in Europe

Price: $650,000

IDECO 2100E DRILLING RIG (Ref#13750N) DRILL FLOOR COMPLETE WITH ALLS, SETBACKS, ETC., 160’ Dreco derrick with crown block, dolly track, fingerboard, casing stabbing board, drill collar stabbing board, windwall at monkey board level, traveling block and hook, dolly for block. (6) 1000 ct/ft bulk tank complete with gauges and load cells. (2) T1600 Ideco triplex mud pumps complete with GE752 motors, Hydril puldation dampeners, control panel and low pressure mud feed pipe work. (2) pecharge pumps, kelly complete with bushing in sock. Ideco E2100 drawworks complete with Elmagco 7040 brake and 2 each GE 752 motors (skid mounted). Degasser system complete withpoor boy. Standpipe manifold and 2-sections of standpipe (rough cut). Transmission chains for mud pumps and drawworks. Shaker house, skid frame. Rig substructure. Control panel for drawworks. (9) agitators for mud tanks, brake cooling wter tank, compressed air reservoir, mud pump manifold (local), (2) skidding pistons and gripper for substructure, (2) skidding pistons for skid base, hydraulic unit for skidding system complete with controls,.

(2) petroline flare booms, (1) swivel, kelly bock, Mathey wireline unit, 37-1/2” rotary table (may not be available), various rig parts.

Price on Request

IDECO 1000M (Ref#13363N) Mounted on 3 axle Lee C Moore trailer, 96’ x 250,000# - 275,000# Lee C Moore Derrick, Double Drum; powered by (2) 8-V71 Detroit diesel, 8x14 Sub base, Shorty 150 ton swivel, 17 ½ cargo table, 36’ Kelley 4 1\4 square, Cameron space saver 3000 BOP with spool, 2” choke manifold with 125 gallon 5 station closing unit, (2) Gardner-Denver 14” F X Q Duplex pump w/ 12V71 Detroit diesel, 300 KW Generator powered by 3406 CAT, 1OO KW Generator powered by 6-71 Detroit, Gen Sets & mounted on single skid with air compressor, Derrick shale shaker, 500 Gallon fuel tank (trailer mounted), 500 BBL water tank, 30’ Enclosed parts trailer/van, TOP dog house trailer with 100 BBL, Hydro water tank, junk box, mounted on two axel float, 180 BBL water tank w/ junk box, stairs, cat walks, oil reserve tank and alleviated dog house assembly, 7000’ of 4 1\2” yellow band drill pipe, 2 – 300 bbl mud tanks with electric agitators, 20 - 6” drill collars with nubbins, tongs, slips for drill collars and drill pipe, elevators for 4 1\2 drill pipe and elevator links, Subs, hand tools, spare parts, 42’ van trailer for parts house or crew quarters

Extra Tools: 118’ x 350,000# - 375,000# Lee C Moore Derrick, N-4 Brewster skid mounted draw-works complete, without power, Spare N-4 Brewster draw-works for parts, Rig was refurbished in 2005 and drilled one well.

Price: $1,300,000

IDECO H1000 DRILLING RIG (Ref#10N) 12,000’ drill depth with 3-1/2” drill pipe, 25,000’ workover depth with 2-3/8” tubing, 1-1/8” drill line, single drum, Ideco Back-In Rambler rig BIR-8005 6 axle (3 front, 3 rear), mechanical drive from carriers front mounted (2) GM 12V71T engines 434 hp at 2100 rpm, (2) Allison torqmatic 5680 transmissions (5 forward, 1 reverse), 22” type B double Hydromatic brake, 112’ x 358,000# Ideco AH Swik-Lift telescoping mast, Ideco crossover type crown with Timken double tapered roller bearings, Sheaves: groove 5/36, 1-42 Fabriform 1-1/8” for 6, 8, or 10 line stringup, traveling block, crown safety platform with handrails, less toe-boards, racking platform at 71’ to work with 16’ substructure 156 stands in 60’ lengths of 4-1/2” dp or 296 stands in 60’ lengths of 2-7/8” tubing. CARRIER has Steerable Schuler 65,000# capacity triple steel front acles and spring suspensions sytem, (6) 18-22.5 x 16 ply nylon front tires with Budd wheels, Clark 60,000# capacity, planetary tandem steel rear axles with Hendrickson suspension system and a single tag axle, one man cab. Ideco 260 ton telescoping substructure 16’ height, telescoped to 13/6” and when mounted on a 2’6” subbase provides 16’ height (9’6” for transport), 320,000# setback capacity, 19’4” wide x 16’4” long floor dims with walkways extended 11’6” wide and 18” long with walkways folded. Hydraulic elevating doghouse base (doghouse not included). Ideco UTB-160-4-36 travelling block 160 ton (4) 36” sheaves grooved for 1-1/8” line, Ideco TL200 swivel 200 tons, Ideco 27-1/2” rotary table, Eckel 13-5/8” power hydraulic tonhs with 5 sets jaws, manual tongs with several sets of jaws, Varco split square 13-9/16” master bushings, 4-1/4” hex kelly, Varco kelly bushing, 2 Omsco 5000 psi kelly valves, Varco kelly spinner, kelly saver sub, lighting system, weight indicator, torque indicator system, 5 pen drilling recorder, Totco drift indicator, (2) Mission 5 x 6 centrifugal pumps, (2) Mission 6 x 8 centrifugal mud mixing pumps. Ideco T1000 7-3/4” x 14” Triplex mud pumps with 950 hp Cat D398DT diesel engine. 318 bbl mud system shaker tank, 318 bbls mud system suction tank, shakers, desander, degasser, agitators. Generator and compressor house with (2) Mustang/Cat 3408 PCT 60 Hz, 1800 rpm, 3ph, 240-480 v, 300 kw standby, 265 kw prime. BOP stack (2) Hydril ram BOP’s flanged and studded 13-5/8” x 5000#. Handling tools for 4-1/2” dp and 6” 7” and 8” DC, tools for casing from 4-1/2” – 13-5/8”, tools for tubing from 2-3/8” – 3-1/2”. (13 jts) 4-1/2 XH heavy weight drill pipe, (20) 6” drill collars, (10) 6-3/4” drill collars, (3) 7” drill collars, (1) 7-1/2” drill collar. Price: $4,000,000

IDECO 725E WORKOVER/DRILL RIG (Ref#6575) 1000 hp diesel electric rig with 400,000# hook/load, Modular platform certified for offshore use, modular concept allows land use easily, Ideco 725E drawworks (900 hp), Parkersburg V-80 brake, 900 hp Toshiba 900A DC electric motor, (2) Caterpillar 3412TA diesel engines with (3) 600 kw generators, Ideco 100’ x 400,000# hydraulically raised and wireline scoped mast, 400,000# substructure will fit up to 56’ platform beam, (2) Ideco T500 triplex mud pumps powered by Toshiba 900A DC motor, (2) 5 x 8 centrigual pumps, Ideco 275K rotary table 27-1/2”, Ideco UTB-265T shorty hook/block, Ideco 300 TL swivel, 250 bbl mud system in substructure with Brandt degasser, centrifugal pump, IPS Model 1000 SCR System, 600 VAC, 3 phase, 60 cycle, 13-5/8” x 5,000# Shaffer double ram BOP, 13-5/8” x 5,000# Shaffer single ram BOP. 13-5/8” x 5,000# Shaffer spherical BOP, Koomey Type 80 Accumulator with 6 station 3000 psi Price Open

IDECO IH-4000 (Ref#774N) Incomplete rig, Ideco IHE4000 drawworks, electric disassembled w/5031 electric brake, no SCR controls, no engines, 1,000,000# GNC mast, 44’ x 4’6” x 8’ pyramid swing up sub base, (2) Oilwell A-1100PT mud pumps w/1000 hp traction motors, 23” rotary table (disassembled), Ideco 350T swivel disassembled, 350 ton McKissick block and 350 T Hydra hook disassembled, 5-1/4” hex kelly, (3) mud tanks, Cameron 5000# double BOP and single annular, 11,000’ of 5” Grade E & C 19.5 drill pipe double white, 17 jts of HWPD 7”-8” x 30’ drill pipe, collars, dlipd, casing elevators, drill pipe elevators, rotary tongs, drilling jars, fishing tools. This rig was imported from South America and requires comletel rebuilding Price: $1,100,000

IDECO H44 CD RAMBLER RIG (Ref#13595N) PARMAC V80 BRAKE, HERCULES HA118 DEADLINE ANCHOR, 2 EACH CATERPILLAR 3408 DITA ENGINES, 1 EACH DETROIT ENGINE, MD TOTCO INSTRUMENTATION, 7 SHEEVE CROWN BLOCK, GARDNER DENVER 22-1/2" ROTARY TABLE, IDECO TL 200 SWIVEL, HARRISBURG DESANDER AND DESILTER, INGERSOLL RAND K4U AIR WINCH, BRADEN HYDRAULIC WINCH, MATTHEY WIRELINE UNIT, TRIP TANK, SUBSTRUCTURE, CATWALK, V-DOOR Price: $1,600,000

IDECO H-44C DRILLING RIG (Ref#13592N)

DERRICK & SUBSTRUCTURE

Ideco 108’/268,000# derrick with Crown-o-matic. Custom-built 300-ton integrally loaded substructure with 18’X21’ floor. 14’ Kelly bushing measurement with 10’10” clear height under rotary beams. Sub and wall section are unitized and mounted on wheels and axles, including hydraulic boom and pipe handling equipment. Substantially rebuilt in 2006.

DRAWWORKS

Ideco H-44 single drum. Powered by two 550 h.p. Cat C-15 diesel engines (new summer 2007) through an Allison 5860 5-speed automatic transmission with circulating brake flanges. Foster makeup and breakout cat heads. 22” single PArmac hydramatic brake. Gearmatic hydraulic pickup winches.

TRAVELING EQUIPMENT

Ideco UTB 160-ton unitized block/hook with four 36” sheaves for 1-1/8” lines. 2-3/4”X90” elevator links. Rebuilt 2006.

ROTATING EQUIPMENT

Ideco LR 20-1/2” rotary table with split master bushing. Ideco TL-200 swivel. Foster Model 77 kelly spinner. 4-1/4”X39’ square Kelly. Varco 4-roller drive bushing. Rebuilt 2006.

MUD PUMPS

MD-8 triplex pump (PZ-8 equivalent) powered by Cummins KTA-38 1,000 h.p. diesel engine. Two Ideco MM550 7-1/4”X15” duplex pumps with forged steel fluid ends with quick change caps, Hydril K-20 pulsation dameners, Demco 2” shear relief valves, manifolded to compound. Each duplex pump powered by Cummins NT 855 670 h.p. diesel engine.

MUD SYSTEM

Two 225-bbl. steel pits with seven compartments, bypass trough and trip tank with top-mounted walkways. Harrisburg 10” single cone desander. Detroit Diesel-powered 5”X6” centrifugal pump with internal plumbing to charge either system. Derrick 500 gpm flow line shale shaker. 250-bbl. steel premix tank with 5”X6” 50 h.p. electric centrifugal pump.

WELL CONTROL EQUIPMENT

Cameron Type “U” 11” 5,000 psi double ram BOP (rebuilt 2007), Cameron Type “D” 11” 5,000 psi annular BOP rebuilt 2006). Koomey 3,000 psi 80-gal. accumulator with four stations and remote control. One 15 h.p. electric triplex and two air charge pumps with nitrogen back-up systems. 5,000 psi choke manifold.

GENERATORS

Cat 210 KW and Cat 200 KW, both new during spring 2007.

DOG HOUSE/FUEL TRAILER

8’X20’ elevated dog house equipped with tool room & knowledge box. Bear automatic driller. 2,500-gal. fuel tank. 80-bbl. fresh water brake cooling and high pressure wash down tank.

DRILL STRING

Approximately 7,500’ of premium (double white band) 4-1/2”, 16.60#, X-95 drill pipe with 4-1/2” XH connections. Four 8”X2-3/16” slick drill collars with 5-1/2” XH connections. Twenty-four 6” slick drill collars (1 bottom hole collar). Two tri-axle pipe trailers. Two sets of pipe racks.

MISC. EQUIPMENT

BJ Super Type “C” tongs w/ 3-1/2” thru 6” heads. Wooley Type “B” rotary tongs with 3-1/2” thru 13-3/8” heads. 500-bbl frac tank. Kelly saver sub, change over sub, ten 6” DC pick-up subs and two 8” pick-up subs. Two junk tubs.

CARRIER

Five-axle drive in carrier. Requires deadman anchors.

Price: $4,000,000

IDECO H-44-CD (Ref#10202N) Manufactured 1975, depth capacity 2600 meters 8530’ with 4-1/2” drill pipe, 580-700 hp, Mast Ideco SBSKM 111’ x 268,000#, single drum drawworks 18” x 35-1/2” w/Parkersburg V-80 brake, 1-1/8” drill line, Foster 77 kelly spinner, (2) Cat D343 TA-A diesel engine, Allison CLBT 5860 transmission, 20-1/2” rotary table, Ideco SBS UTB-160-4-30 160 ton block, 4 sheaves, Ideco SBS TL200 200 ton capacity, Ideco T-1000 triplex mud pump 7” x 10” 368 band per minute w/4-1/2” liner, Harrisburg 5 x 6” charge pump, (2) 3512TA and D399 generators 857 kw, (3) tanks 2683.92 ft³, 1006.47 ft3 (37.73’ x 7.15’ x 9.51’), 847.55 ft3 (31.2’ x 7.15’ x 9.51’), 812.24 ft3 (36.09’ x 7.15’ x 9.51’), complete rig less drill pipe and collar

18 loads - $200,000 to ship to Houston Price: $3,000,000

IDECO RAMBLER H37 (Ref#13856N)

1979 IDECO Rambler H37 Single Drum Carrier-Mounted Drilling Unit, LEBUS Grooved f/I” Drill Line, Ezy-Torque Hydraulic Breakout, PARMAC 15” Double Hydromatic Brake p/b DETROIT 12V-71 Diesel Engine Air Starter, ALLISON 5860-4 Transmission, IDECO 104’H Telescoping Mast, Hydraulically Raised & Scoped, Single 3-Stage Hydraulic Raising Ram, Racking Board, Standpipe, All Mounted on IDECO BIR5525 5-Axle Carrier, Hydraulic Halliburton Wireline Measuring Device, BRADEN Winch, Water Tank, Fuel Tank, Folding Walkway, Stairs, Safety Rails, 12.00x20 Tires, Budd Wheels

SUBSTRUCTURE 8’H Substructure w/Rotary Beams, Stairs, Safety Rails

DRILL MATS New folding steel rig mats.

ROTATING EQUIPMENT New 27-1/2” Rotary Table, IDECO Tru-Line 200-Ton Swivel, New 4-1/4” x 40’L Square Kelly

AUXILIARY EQUIPMENT Clipper-Type Weight Indicator, SATELLITE Automatic Driller

4”ID x 55’L Rotary Hose

(2) 3”ID x 6’L Vibrator Hoses

(2) 8” ID x 14’L Suction Hoses

Fluorescent & Mercury-Vapor Rig Lights w/Wiring

TRAVELING EQUIPMENT IDECO Shorty 150-Ton Block/Hook Combination w/(4), Sheaves, New 1” Line, 3” x Approximately 72” Elevator Links

RIG HOUSES (2) Shop built, 8’ x 40’ Insulated Doghouse w/LPG Heater, Lockers, Tool Racks, Parts Racks

FUEL TANK 2,000-Gallon Fuel Tank

HANDLING TOOLS

BJ Type B Rotary Tongs w/(4) Sets Heads

WOOLLEY 150-Ton Center Latch Drill Collar Elevators

(2) 4-1/2” Drill Pipe Slips

Type C Drill Collar Safety Clamp

(6) Drill Collar Lift Subs

(12) Assorted Changeover Subs

10” Shock Sub

22-5/8” Roller Reamer

28-3/4” Roller Reamer

Approximately 200’ of 1” Drill Line w/Spool, Stand

POWERED PUMP

WILSON 600 Duplex Mud Pump, Forged Steel Fluid End w/Quick-Change Caps, Pulsation Dampener, Shear Relief Valve, Drive Assembly p/b DETROIT Twin 6-71 Diesel Engines w/Air Starter, Radiator, Gauges, Master Skidded

POWERED PUMP

EMSCO D-300 Duplex Mud Pump, Cast Fluid End w/Bolted Caps, Surge Chamber, Shear Relief Valve, Pressure Gauge, Drive Assembly p/b DETROIT Twin 6-71 Diesel Engines w/Electric Starter, Radiator, Gauges, Master Skidded

DRILL PIPE

2294’ (74 Joints) 4-1/2”, 16.60#, Range 2 Drill Pipe w/4-1/2”XH, BN Tool Joints, 6” OD Avg, DWB

DRILL COLLARS

(6) 9”OD x 3-1/2”ID x 31’L Spiral Drill Collars w/7-5/8” Reg.

(3) 11”OD x 3-1/2”ID x 31’L Spiral Drill Collars w/7-5/8” Reg.

ROLLING STOCK/CONSTRUCTION EQUIPMENT

1964 CAT 977H Crawler Loader,

Komatsu PL160 Hydraulic Excavator

(2) 40’ tandem axle float trailers

MUD SYSTEM

(2) 8’ x 7’H x 30’L Steel Mud Pits

Shale Shaker

Desander

New, unused Mission 6” x 8”, 60 HP desanding pump

Currently drilling.

Price: $1,400,000 Price reduced to $1,175,000 for quick sale

IDECO H-37 (Ref#6059N) Manufactured 1978, Ideco double drum drawworks, 42 x 10-1/2” main drum with circulating brake flanges, 1-1/4” drill line, Parmac 215 hydromatic brake with 250 gallon cooling fluid, 38 x 8 sand drum with 14,000’ of 9/16” line, 2005 Cooper style 104’ x 250,000# hydraulically raised and scoped mast with 5 crown sheaves to accommodate 8 line string up with 4” standpipe, working rod basket, all guy lines, mounted on 5 axle Ideco back-in Rambler carrier with Detroit series 60 (550 hp) diesel engine, Allison 6061-4 6 speed transmission, rig is equipped to operate rotary drive system, currently strung with 4 lines, 150 ton 3-sheave Sowa block, operator’s platform and work platform can be moved up to 12’ off ground, deck mounted dealine with weight indicator Price: $825,000

IDECO H-37 (Ref#7099) 550 hp BACK-IN RIG#2 Ideco H37 double drum with 15” Parmac, powered by Detroit 12V71N with Allison 5860 transmission, Ideco 103’ x 224,000# hydraulically raised mast, 4” standpipe, Ideco UTB 160 ton unitized hook/block, Ideco TL 200 ton swivel, 4-1/4 x 40’ square kelly, 17-1/2” Ideco rotary, mounted on 5 axle self-propelled carrier. Substructure 300 ton with 18’ x 21’ floor space, 14’ KB measurement with 10’10” clear height, substructure and walk section are unitized for wheel mobilization including hydraulic boom and pipe handling equipment. Ideco MM550 7-1/4 x 15” duplex w/ Hydril K20 with (2) 8V71 (600 hp) Detroits wheel mounted. Ideco MM550 7-1/4 x 15 duplex with Detroit 12V71 (475 hp) wheel mounted, (2) 225 bbl steel pits with 6 compartments wheel mounted with desander, Detroit 353 powered 5 x 6 centrifugal pump and shale shaker, Cameron 11” x 3000# annular, Cameron 11” x 3000# type U double ram and 80 gal accumulator, (3) 8 x 2-1/4 DC, (21) 6-1/2 x 2-1/4 DC, 7000’ 4” FH grade E drill pipe, 1500 gal diesel tank, 40 kw Cummins powered on trailer, doghouse, 550 bbl frac tank, drill pipe and casing tongs, highly mobile active rig in field ready condition Off Market

IDECO H37 Back-In Rig (Ref#4949) Manufactured 1977 - 103’ x 224,000# hydraulically raised and scoped mast,heavy duty hydraulic hoist, (1) 12V71 Detroit engine, Allison transmission, 3 sheave 150 ton Shorty hook/block combination, torque converter, 3-1/2” kelly hose (nearly new), 4” standpipe, kelly spinner w/reverse (new), ramp and 9-1/2' - 12' telescoping substructure, all new guide lines and anchor sheaves, transfer case (recently reconditioned), 18" rotary table, hydraulic hoist, rig lights, 125 ton reconditioned Gardner Denver swivel Off Market

Available at extra cost:

Reconditioned Cameron double shorty 10” BOP with blind rams: 4-1/2”, 3-1/2” and 2-7/8” pipe rams

Reconditioned Hydril 10” annular

3-station 80 gallon closing unit with electric pump and nigrogen back up system

(2) 100 kw Cummins generators mounted inside of 8’ x 25’ doghouse with side and end doors

6000’ of 4-1/2” 16.60# yellow band drill pie with 6” tool joints and 4-1/2 XH connections

(40) 6” x 30’ x 2-3/8” ID and 4” H-90 connections

Martin Decker weight indicator, Type B rotary tongs, pipe racks, pipe tubs, 40’ hex kelly, hex kelly bushings, elevator links

12” Gardner Denver with (2) 671 Detroit diesels

14” Oilwell with (2) 671 Detroit diesels

IDECO H35 WELL SERVICE RIG (Ref#5327N) Manufactured 1978, 95’ x 212,000# mast, derrick inspected July 2007, rig completely rebuilt August 2007, 11.1 Series 60 Detroit, 4460 automatic transmission, mounted on 4 axle back in carrier, 15” double hydromatic brake, 10” x 42” main drum with 825’ of drill line (for 6 line blocks), 8” x 42” swab drum with 7000’ of 9/16” swab line, 100 ton blocks, note rig has been working since August 2007, tooled out with rebuilt 5893R Foster tongs with air backup and lifting cylinder, 100 ton Bash Ross blocks inspected in 2007, BJ rod tongs with ¾”, 7/8:” and 1” heads, 72” bails (inspected), 100 ton 2-3/8” and 2-7/8” elevators (new), 100 ton Cavin air slips (new), rod table, wiper box, guy wires, derrick climber, dog house, 240,000# Totco indicator, aluminum mats, oil saver and pump. Currently working. Price: $650,000

IDECO H35ED (Ref#10391N) Workover/Service rig, Ideco H35ED double drum drawworks, 1” drill line, 9/16” sandline, 95’ x 140,000# hydraulically raised and scoped mast Model KM90/95-180 GH, substructure 15’L x 8’ W x 15’H, mounted on 4 axle Carrier with Detroit 12V71 diesel engine (400hp) and Allison TC955 transmission, torque converter, hydraulic handling winch, power take off for tong operation, Ideco SBS Model EFB108 hook/block 95 ton, Bowen S25 power swivel 85 toin, 3200 lb/ft torque powered by Detroit 6M53 diesel engine, skid mounted, located Europe Price: 365,000 Euros

Additional equipment available: tubulars, pumps, BOP, mud tank

IDECO H35 DOUBLE DRUM WORKOVER RIG (Ref#876N) 180,000 lb Derrick, Double Triple 96' Derrick, Double Drum Drawworks, 4 line speed block w/ swivel, Foster Tongs, Gyberson Double 3000# BOP, Oil Saver & Swabbing Equip., Rod & Tubing Elevators & Tools, 5500' of New 9/16" Swab Line, New 1" Drill Line (560'), New 5/8 Cat Line, New Tong & Rod Lift Line, New Tires, 8V71 Detroit, Transmission, Completely Rebuilt Schuller Front End, New Drive line from Front to Back & New Third Member & U-Joints, New Hydraulic Pump w/ Eaton Air Clutches, All new Brake Cans, New Rebuilt Tubing Board, New Battery, Starter & Gauges, Most air & hydraulic line has been replaced or updated ~~Price~~~~: $640,000~~ REDUCED PRICE: $500,000

IDECO H35 WELL SERVICE DRIVE IN RIG (Ref#5162N) Manufactured 1970’s, Ideco 96’ x 215,000# mast, rig being rebuilt, new series 60 Detroit, automatic transmission, 4 axle carrier, hydromatic, driven in Price: $735,000

IDECO H-35 (Ref#11793) H-35-KD drawworks with torqmatic transmission CLBT 750DB, mounted on 4 axle back-in carrier, KM 90-212GH hydraulically raised mast w/4 sheave crown block, work platform, lighting system, powered by 3306PC-T diesel engine, McKissick 659 travelling block/hook, single shale shaker tank 17.5 cbm, hopper w/3x4 centrifugal pump, 3 mud agitators. F650 triplex mud pump w/K20-5000 pulsation dampener mounted on trailer w/3412 DITA diesel engine, PTO, workshop and storage w/tools, mud circulating system w/shale shaker tank 15 cbm, suction tank and mud gas separator, located Europe. Price: $350,000

IDECO H-35 (Ref#7102) 500 hp BACK-IN WORKOVER/DRILLING RIG #6, Manufactured 1996, Ideco H35 single drum w/15” Hydramatic, powered by Cat 3408 (500 hp) w/Allison 5860 transmission, Ideco 105’ x 225,000# hydraulically raised mast, 3-1/2” standpipe, Ideco 140 ton hook/block and Scott power swivel, Substructure workover: 88” deep x 94” wide w/2-1/2’ wings telescopes from 2’ - 7’ with 38’ center rub, Substructure drill: 200 ton, 16’ x 18’ floor space, 13 kb measurement w/10’6” clear height, substructure and walkway unitized and wheel mounted with hydraulic pipe handling accessories and 5’ pony sub, Wilson 600 duplex 6-1/2 x 14” powered by 3408 Cat (550 hp), wheel mounted, 225 bbl pit with walkway and 50 hp electric 5 x 6 centrifugal pump and 4 x 5 shale shaker wheel mounted, Shaffer 7/16 x 5000# type LS double ram and Cameron/Payne, 3000# 80 gal accumulator, (24) 4-3/4 x 2-1/4 DC and 8,500’ of 2-7/8 IF grade E 10.40 drill pipe, 250 kw Cat generator with 3406 Cat, 8’ x 40’ doghouse wheel mounted, tongs, handling tools, 550 bbl frac tank Off Market

IDECO H-35 (Ref#7098) 500 hp BACK-IN RIG#1 Ideco H35 double drum with 15” double Parmac powered by Detroit 8V71N and Allison transmission, Ideco 95’ x 212,000# hydrauilcally raised mast, 3-1/2” standpipe, Ideco 110 ton unitized hook/block, Ideco TL200 swivel, 4-1/4” x 40’ square kelly, 17-1/2” rotary table, mounted on 5 axle self-propelled carrier. Substrucutre 200 ton with 16’ x 18 floor space, 13’ KB measurement with 10’6” clear height, substructure and walk section unitized and wheel munted including hydraulic pipe handling accessories, Ideco MM550 7-1/4 x 15” duplex with Hydril K20, with (2) 8V71N (600 hp) diesel engine, wheel mounted, Ideco MM300 7-1/4 x 12” duplex mud pump with Detroit 8V92TA (380 hp) engine, wheel mounted, (2) 225 bbl steel pits with 6 compartments, walkway wheel mounted with desander, Detroit 353 powered 5 x 6 centrifugal pump and shale shaker, Cameron 11” x 3000# annular, Cameron 11” x 3000# double ram, Koomey 80 gal accumulator, 1500 gal diesel tanks, 40 kw Cummins generator on trailer, (3) 8 x 2-1/4 DC, (20) 6-1/4 x 2-1/4 DC and 5000’ of 4” FH grade E drill pipe, doghouse, water storage, drill pipe and casing tongs. Highly mobile active rig in field ready condition. Off Market

IDECO H25 (Ref#1366N) Ideco Rambler 16 wheel trailer w/H25 drawworks, Cardwell 94’ x 150,000# mast w/5 sheave crown, 200 barrel mud tank w/4 cone desander, National K500 duplex mud pump w/Cat D353 diesel engine in 10x30 building, doghouse/water tank building, light plant/combination building, catwalk, 2 new pipe tubs, no block, no hooks Price: $1,100,000

IDECO H25AD WORKOVER RIG (Ref#15307) double drum, 96’ x 180,000# mast, mounted on 3-axle trailer, powered by 671 Detroit diesel engine, hydraulic leveling jacks, The truck in photo is used to pull around yard (not included) Price: $170,000

IDECO 3000 (Ref#1639N) 110 hp, Manufacturted 1974, GMC 671VA-37617 With 110 Hp, 96’ X 200,000# Double Derrick, Double Drawworks 150,000# Capacity, Wilson 6-1/2 x 14 mud pump on gooseneck trailer, 22” rotary table and a Principal Traveler not inegrated in the rig, 4-1/2” x 11 meter kelly (4” bushing) with 100 ton Ideco swivel, 300 meters of 4-1/2” x 9 meter drill ipe, (2) forward hydraulicjacks, (2) backward hydraulic jacks, (2) 7-1/4 x 8 meter drill collars, (2) Wilson tongs, elevators, 4-1/2” drill slips, 8” drill collars Price: $375,000

IDECO SBS EW 60/14 (Ref#1702Nb) Manufactured 1995

CHASSIS: MAN/ÖAF, 3 axles: 1 driven steerable front axle, 2 driven rear axles, leveling jacks: 6 hydraulic jacks, 2 mechanical jacks

ENGINE: MAN D 2866 LF15, 272 kW (365 HP)

MAIN DRUM: drum size: diameter 444 mm, width 970 mm, with Lebus grooving, drum clutch: 30CB525, brake rims water cooled

AUXILIARY WINCH:2 hydraulic winches, winch capacity app. 4500 lbs (2000 kg) each, line diameter 11 mm

WINCH CAPACITY: 4 or 6 lines

LINE: line diameter 7/8"

MAST: single mast, max. mast height 55 ft (16.8 m), max. static mast capacity 190,000 lbs (86 to)

TRAVELING BLOCK: DUTB 75224 B, max. load 75 ton

DIMENSIONS & WEIGHT: weight app. 57,300 lbs (26 to), length app. 50 ft 6 in (15.4 m), width app. 8 ft 2 in (2.5 m), height app. 13 ft 1 in ( 4.0 m)

Price: $435,000