SUN MACHINERY CORP

Telephone:  (516) 536 7375                    Fax:  (516) 536 7317

These rigs are located at various locations through out the USA and  Internationally.

e-mail:   rigs@sunmachinery.com

Gardner Denver, Mayhew   DSM1350, DW500, 3000, 2500, 2000, 1500, 1400, 1000, 500, 200, 15W, 14W

 

 

DSM 1350 (950 HP) MECH, SKID MOUNTING DRILLING RIG (Ref#1964Na)  

CONDITION RATING: GOOD

DRAWWORKS  DSM 1350  Single Drum Drawworks, 7” Shaft, LEBUS Grooved f/1-1/8” Line, Makeup & Breakout Catheads, Air Driller’s Console Controls w/ Rotary Drive Sprocket.

COMPOUND  2-Engine, In-Line Compound w/ (2) Quincy 325C Air Compressors (New)

BRAKE  PARKERSBURG 36” Brake

ENGINES  (2) DETROIT Series 60 Diesel Engines, 470-HP, Each w/ Electric Starter, NATIONAL 955 Torque Converter, Air Clutch & Each Skidded

MAST  SUPERIOR 133’ Cantilever Telescoping Mast, 470,000Lb. Static Hook Load, Pin Type, T-Sheave Crown w/ Crown Safety Platform, Racking Board, Line Boom, Tong Counterweights, Derrick Climber, Ladder, Deadline Anchor, 4” Standpipe Manifold w/ 4”& 2” Gate Valves, CAMERON Type D 3000# Pressure Gauge & Mast Stand.

SUBSTRUCTURE  12’H x 20’W x 50’L Box-Type Substructure w/ V-Door, (3) Stairs, Safety Rails, 400,000LB Capacity & Pin Together in Middle.

PUMPS

2003 MZ-9FES Triplex Mud Pump, 1,000-HP, Forged Steel Sectional Fluid End w/ Quick-Change Valve & Cylinder Head Caps, HYDRIL K-20 3000# Pulsation Dampener, O’DRILL 2” Shear Relief Valve, MISSION 5” x 8” Centrifugal Charging Pump, Type D 5000# Pressure Gauge, Drive Assembly, Master Skid, p/b CAT D398 Diesel Engine w/ Air Starter, Air Clutch, Skidded & Belt Driven.

NATIONAL K500A Duplex Mud Pump;  Forged Steel Fluid End w/ Quick-Change Valve & Cylinder Head Caps, HYDRIL K-20 3000# Pulsation Dampener, O’DRILL 3” Shear Relief Valve, Type D 5000# Pressure Gauge, 2” Gate Valve, DEMCO 4” Gate valve, 8” Butterfly Valve, Drive Assembly, V-Belts, Belt Guard, Skidded & Compound Driven.

ROTATING EQUIPMENT  SKYTOP BREWSTER RSB-180 Rotary table, 17-1/2” x 44”, w/ Split Master Bushing., 225-Ton Rotary Swivel, 5-1/4” x 41’L Hex Kelly w/ VARCO Kelly Drive Bushing & Pin Drive.

TRAVELING EQUIPMENT  EMSCO NC-36 125-Ton Block/Hook Combination, 4-Sheave, BJ 4125-Hook;

2 1/4” x 72” Elevator Links.

WELL CONTROL EQUIPMENT

HYDRIL GK 5000# Annular Blowout Preventer.

Cameron Space Saver 5000# Double Blowout Preventer w/ 4-1/2” Pipe & Blind Rams.

4-Station Closing Unit, Cameron w/ no Pump or Remote Control Panel.

CAMERON 5000# Choke Manifold w/ (4) 2-1/6” Valves, (2) 4” Valves, (2) Adjustable Chokes, Pump Gauge, 5-Way Cross, Plumbed w/ 2” & 4” Pipe & Skidded.

RIG HOUSES

7’W x 20’L Doghouse w/ 6’L Porch Extension, Round Top, Knowledge Box, Lockers, Bench Storage, Cabinets, Fluorescent Lights.

GENERATORS/UTILITY HOUSE

2 each175 KW AC Generator p/b CAT 3306 Diesel Engine. Electric Start & Skidded.

325C Air Compressor p/b 5 HP Electric Motor, Mounted on Air Receiver Tank

All Above Mounted in 8’ x 40’ Utility House w/ Round Top, 13’L Change Room w/ Lockers, Bench Storage, Heater, Fluorescent Lights & Skidded.

MUD SYSTEM

6’H x 10’W x 42’L 400-Barrel Mud Suction Tank w/ (2) Compartments, V-Bottom, (2) Mud Stir Units, Each 50-HP p/b Electric Motor, Jets, (2) MISSION 6” x 8” Centrifugal Pumps, Each p/b Electric Motor, (2) Mud Hoppers, 2 Mud Agitators Top-Mounted Walkways, Stair, Safety Rails, Skidded

WATER / FUEL TANK

6’H x 10’W x 42’L 400-Barrel Water Tank w/ 3’L Covered Skid Extension,

MISSION 2” x 3” Centrifugal Pump p/b Electric Motor,  8” Dia X 21’L Fuel Tank w/1” ½ HP fuel pump, Skidded.

HANDLING TOOLS

BJ Type B Tongs w/ Heads

4-1/2” Center Latch Drill Pipe Elevator

6-1/2” Center Latch Drill Collar Elevator

4-1/2” Drill Pipe Slips

6-1/4” 10-Segment Drill Collar Slips

BAASH-ROSS 10-Segment Drill Collar Safety Clamp

Mud Saver Bucket

INGERSOLL-RAND HU Air Hoist,

AUXILIARY EQUIPMENT

BEAR Automatic Driller

GEOLOGRAPH Pioneer Single-Pen Recorder,

MARTIN-DECKER 360,000Lb. Capacity Weight Indicator

TOTCO Straight-Hole Deviation Instrument

31/2” x 60’ Rotary Hose

36”H x 5’10”W x 38’L 2-Section Catwalk w/ Steel Deck & Steps

(3) 36”H x 6’W x 38’L Pipe Tubs

(2) 28”H x 6’W x 38’L Pipe Tubs

Electric/Hydraulic Wireline Measuring Device

Rathole & Mousehole

Fluorescent & Mercury-Vapor Rig Lights w/ Wiring

3000’ 1 1/8”Drill Line (New),  Spool & Stand

PIPE RACKS

2 Sets of (4) 36”H x 34’L Triangular Pipe Racks

2 Sets (2) 36”H x 11’L Triangular Pipe Racks

(no drill string with rig)

Extensive work done to make rig work ready, including new wiring and lighting, new plumbing (air, fuel, water, hydraulic), all structural repairs to the main components and repairing or replacing ladders, steps, handrails, and sheet metal, repairing, rebuilding and servicing all power units, pumps and drawworks as necessary, doing all cosmetic repairs including sandblasting, cleaning and painting.

Price:  $2,775,000

 

GARDNER DENVER DW500  (Ref#11122N) 

Drawworks:  Gardner Denver Model SW500 drawworks, main drum grooved for 1-1/8” drill line and powered by (2) Cat C15 industrial engines

Parmac type V80 hydromatic brake

Mast:  136’ clear height Superior Derrick Services, 18’6” base, 600,000# GNC, 428,000# static hook load mast with crown cluster consisting of (6) 42” dia sheaves and (1) 55” dia fastline sheave, all grooved for 1-1/8” wire line

Substructure:  15’, box on box conventional substructure with 450,000# rotary capacity, 300,000# set back capacity and 750,000# simultaneous rotary and setback load

Travelling equipment:  Ideco Model UTB-265, 265 ton unitized hook/block combination, complete with (5) 36” dia sheaves, King Oil Tools Model 25MB-14, 300 ton capacity swivel, Owi Model 1500 kelly spinner.

Gardner Denver RT22-1/2” rotary table, chain driven off the drawworks rotary countershaft and complete with Varco MSPC solid body pin drive master bushing and type “20-HDP” pin drive kelly bushing for a 5-1/4” API hexagonal kelly

(1) Shaffer type LWS 11” x 5000 psi double ram type BOP

(1) type GK 11” x 5000 psi annular preventor BOP

(1) 5-station Koomey type 80 BOP controlunit, complete with remote control panel

(1) 2” x 4” 5,000 psi WP choke manifold

(1) 36” OD atmospheric degasser, unitzed on a single oilfield type skid.

Mud pumps:  (2) Hong Hau Model F1000 triplex mud pumps, powered by Cat D399TA diesel engines, suctions charged by a 6” x 5” Series 178 centrifugal pumps and Emsco style discahrge pulsation dampeners

Mud System:  (2) tank mud system of approx 773 bbl total capacity.  Shaker tank of approx 405 bbls with (2) 6” x 5” Series 250 centrifugal pumps, powered by a 50 hp AC electricmotor, (1) Derrick 12 cone desilter, (1) Derrick 2 cone desander, (1) Derrick vacu-flo 500 degasser, (1) Derrick DE-AG-7.5H, 7.5hp horizontal mud agitator, (2) Derrick FC313 linear motion shale shakers

Suction tank of approx 368 bbl with (2) 6” x 5” Series 250 centrifugal pumps powered by a 50 hp AC electric motor.  (4) Derrick DE-AG-7.5H, 7.5 hp horizontal mud agitators.  O’Drill 6” mud mixing hopper complete with venturi.

Water tank:  (1) 470 bbl capacity water tank, complete with (2) 3” x 2” Series 250 centrifugal water pumps powered by 20 hp AC electric motors.

Electrical System:  (2) 320 kw generators powered by (2) Cat C15 diesel engines, complete with switchgear and transformers.

Aux Equipment:  (1) Nov Wildcat automatic drilling system, (1) 4-pen drilling recorder, (1) retriever wireline measuring unit complete with 15,000’ of .092” wireline, (2) Ingersoll Rand FA2.5A-20XK1 air hoists complete with 5/8” wireline, (1) air powered chain driven drill line spooler.

Compressed Air System:  (1) Quincy Model QSB-40 air cooled rotary screw packaged air compressor unit delivering 165 cfm at 125 psi and powered by a 40 hp AC electricmotor and complete with 200 gal air receiver.  (1) Quincy Model QR390-20 unitized base mounted air compressor delivering 70 cfm at 125 psi and powered by a 20 hp AC electric motor.  (1) 500 gal air receiver mounted in the substructure.  (1) Airtek Model ECP165 refrigerated air dryer.  (1) Airtek model ECP80 refrigerated air dryer mounted in the substructure.

Rig Site Structures:  (1) drill floor house at driller’s position.  (1) crew change/toolhouse, (1) toolpusher quarters/office unit, (1) crew quarters unit.

Drill String:  4-1/2” OD, 16.60 lb/ft, Range II, Grade G105 drill pipe, 8” OD x 30’ long spiral drill collars, 6-1/4” OD x 30’ long slick drill collars, 4-1/4” square kelly, upper kelly valve, lower kelly valve, bit and cross over subs

Hanlding tools:  250 ton Handling tools for drill pipe and drill collars

Price:  $3,750,000

 

 

GARDNER DENVER 3000  (Ref#8732N)  18” Gardner Denver RT-18 rotary table, double drum drawworks with 132,000# capacity with 6 lines, 4 hydraulic leveling jacks, mounted on 3 axle trailer, GMC 671 engine, Detroit Series 60 diesel engine, double section mast 98’ x 200,000#, 2 catheads, located Mexico  Price delivered to Texas border:  $880,000

 

GARDNER DENVER 3000  (Ref#1129N)  Manufactured 1981, 5500’ depth capacity, 96’ hydraulically raised mast with racking board, mounted on 3 axle trailer, (2) 8V71 Detroit diesel engine, Allison transmission 4460, block grooved for 1” on 8 lines, 17-1/2” rotary table, 10’ x 38’ substructure mounted on mud boart with wings and hand rails, Emsco D300 duplex mud pump, quick change fluid ends, powered by Detroit 60 Series engine, 1300 gal fuel tank and toolhouse, mud pump, fuel tank and toolhouse mounted (as one load) on a 2-axle lowboy, kelly float:  kelly 4-1/4” x 4-1/4” x 38’ with mushrooms drives, (12) 6” OD x 2-3/8” ID dril collars (double zips), rathole digger, misc subs, bits and junk box, (3) pipe tubs with 5000’ of 4” drill pipe, (1) 40 kw generator powered by John Deere 4 cyl., 350 bbl frac tank with water pump and work lights, Gardner Denver mixing pump powered by 6VT diesel engine  Price:  $1,300,000

 

GARDNER DENVER 3000 (Ref#6816N)  Single Drum 7/8" line rated @ 250,000 lbs.  325 hp John Deere, 5/1 Allison Transmission, hydromatic brake, 15 1/2 double with closed system, 54' pivot 59' total mast, 200,000 lb. hoisting capacity, Mounted on 4 axel Pearce Carrier, Rig structure: 40.6' x 8.5' x 9', (3) 80 gallon air tanks, (2) outriggers, (2) pivot arms, wire line, rig ramp, dog house, (4) 3/4" support lines, steel mud pits, Hydraulic house & light plant, pump house, (2) water tanks, 43' x 5' x 3.5 catwalk, (3) sets of pipe racks, misc. drill collars, slips, lifting subs. 

Additional information available upon request.

PRICE:  $3,300,000.00    PRICE REDUCED TO: $3,100,000 or make offer

 

GARNDER DENVER 3000  (Ref#7587Nc)    mounted on 3-axle trailer, twin GM 6 cyl diesels, 95’ telescopic mast,k 18” rotary table, Gardner Denver 7-1/2 x 10” mud pump, 125 ton swivel.

100 joints of 5” x 30’ drill pipe, (4) joints of 82” x 30’ drill collar, (2) joints of 62” x 30’ drill collar, (2) lift subs, complete set   Price: $575,000

 

GARDNER DENVER 3000 (Ref#7587Nd)  mounted on 3-axle trailer, twin GM 6 cyl. Diesels, 95’ telescopic mast. 18” rotary table. Deck mounted, 7 ½” x 10” GD mud pump, 125 ton swivel.  90 joints of 3-1/2” x 30’ drill pipe, (4) joints of 8”x30’ drill collar, (2) joints of 6”x30’ drill collar, (2) lift subs, complete set subs groups for drill pipe, drill collar & bits up to 17 ½ dia., pair of tongs, drill pipe elevator, (2) slips for pipe and collars  Price: $495,000

 

GARDNER DENVER 3000 TRAILER MOUNTED DRILLING RIG (Ref#5481N)  Depth capacity: 4,000’ with 4-1/2” drill pipe, Double drum drawworks, 85’ x 110,000# two piece hydraulically raised and scoped mast, 17-1/2” rotary table, 6V71 Detroit diesel on deck, Gardner Denver 7 ½ x 10 duplex mud pump with 471 Detroit diesel engine, Mounted on 3 axle truck, 4 leveling jacks on rig, 2 leveling jacks for mast, Racking board, Kelly hose, Travelling block, Kelly and kelly bushing, Hook, block, swivel, Clean condition, Located in Mexico   Price: $650,000

 

GARDNER DENVER 2500  (Ref#3701N)  Rig only (no mast), twin Detroit Series 40 engines, single drum, no table or kelly  Price:  $80,000

 

GARDNER DENVER 2500  (Ref#4861N)  double drum, 7-1/4 x 14” FXN mud pump, 8V92 Detroit diesel engine, 750 Automatic transmission, 18” Howard Turner table, 75’ GD mast, no pulldown, (2) 75 ton Gardner Denver blocks, trailer mounted, 4 jacks, catwalk, doghouse, fuel tank, 500 gal water tank, 75 kw generator, 2000’ of 4-1/2” x 30’ dill pipe  Price:  $580,000

 

GARDNER DENVER 2500  (Ref#4618N)  single drum drawworks, 250 hp input, main drum grooved for 7/8”: wireline w/Eaton brake, drive engine is being updated to a Volvo diesel engine with Spicer 8031C manual transmission, Gardner Denver Model 65-S round tubing constructed 65’ clear working mast, 57,750# with 4 lines and 65,000# with 6 lines, mounted on 16 wheel carrier trailer with walkways, rais, stairs, dlycol tank, steam heaters, fuel tank, Alpine single piece substructure (attached to trailer) 12’ wide x 30.5’ long x 12’5’ high with built-in rotary table support beams, raising cylinders, mud line and BOP trolley and backin ramp., Oilwell SA-17.5 rotary table with split master bushing, 2500’ of 7/8” x 2500’ drilling line, 3” x 55’ rotary kelly hose. 

Emsco D375 (375 hp) duplex mud pump with Emsco pulsations dampener, pressure gauge, liner wash pump, relief valve and shoke hose, Detroit diesel 8V92T in steel fabricated building 10’W x 29’L x 8’H.

Sloped-bottom single tank mud system, 52m capacity, linear motion shale shaker, standard mix hopper, Mission Magnum 5 x 6 centrifugal mix/precharge pump, degasser

BOP 7-1/16” x 3000# Regan diverter, Guiberson 7-1/16” x 3000# single gate ram, Guiberson 7-1/16” x 3000# single gate ram preventor, Koomey accumulator type 80, choke manifold, choke and kill line valves,

80 joints (approx 2500’) of 3-1/2” 15.5lb/ft grade E drill pipe with 3-1/2 IF conn

23 joints of 3-1/2” heavyweight drill pipe with 3-1/2 IF conn

6 joints of 6” OD drill collars with 4-1/2 XH conn

Brewster 50 ton hook/block

King 75W 50 ton swivel

3-1/2” x 37’ square kelly, kelly bushing, Wooley type B manual rotary tongs, elevator links, handling tools

Miscellaneous building and structures including water tank/toolhouse/doghouse, light plant, managers shack, air compressor package, instrumentation, water and fuel pumps, electrical system, safety equipment

Price:  $3,100,000

 

GARDNER DENVER 2500  (Ref#8780N)  18” Gardner Denver RT18 rotary table, double drum with 80,000# capacity with 6 lines, mounted on 3 axle trailer, 4 leveling jacks, GMC 71 engine, 88’ x 119,000# mast,  2 catheads, Gardner Denver FK-FXK 7-1/2 x 14” mud pump mounted on 5th wheel trailer.  Located Mexico.  Price, delivered to Texas border:  $400,000

 

GARDNER DENVER 2500 (Ref#1373N)

Fully equipped Canadian rig

RIG

Carrier:  Utility Rig 16-Wheel carrier trailer

Drawworks Engine:  Volvo 350 HP, Spicer Transmission

Derrick:  2500 Gardner Denver Conventional Single

Tubulars:  Range III Capacity Casing

Fuel Capacity:  Day Tank

Depth Rating:  1,400 m

SUBSTRUCTURE

Dimensions:  3 m/3.3 m/12.5 m (hwl)

Lift:  KB  3.25 m

BLOWOUT PREVENTERS-CLASS III

Annular Type:  Regan Taurus 7' 1/16"

Single Gates (2):  Guiberson 7' 1/16" x 3000 psi wp

NACE trimmed:  Yes

DOG HOUSE & JUNK BIN

11,000 L fuel and storage room

HYDRAULIC PIPE TUBS

Number:  1, Catwalk:  Yes, Pipe Racks:  1 Set

MUD PUMP

Type:  Emsco D-375, Rated  375 HP, Liner:  140 mm X 356 mm Strokes, Fuel:  Day tank

MUD TANK

Capacity:  52 m3

Shale Shaker:  DFTS 500 B-2 linear

Mud Mixing:  Centrifugal Mission Pump

BOP Manifold:  Centrifugal Mission Pump

Pre Charge Pump:  75 mm x 50 mm 21,000 kPa

DRILL PIPE (UPSET)

Joints:  102, Size:  89 mm, Length:  Range 2, Connections:  3.5" IF

DRILL COLLARS

Joints  3

Size:  159 mm

Length:  Range 2

Connections:  Hevi-Wate, 4 1/2 XH, 3 1/2" IF (20)

COMBINATION BUILDING

Water:  35 m3

Fuel:  Day Tank

Change House:  Yes

Light Plant:  200 KW Generator

Accumulator:  Koomey 4 Station

MOUNTED AIR COMPRESSOR

Yes

BOILER

Horse Power:  80, Water:  16 m3, Fuel:  Day Tank

TOOL PUSH SHACK

3 m Wide x 13.68 m Long

LOADS

Summer:  9

Winter:  10

Price on Request

 

 

GARDNER DENVER 2500  (Ref#12475)  trailer mounted, rotary table opening 32” spiral bevel gears, fully closed and mechanically driven 4 forward, 1 reverse.  Special air actuated cathead for spinning or breakout.  Brakes: mechanically high leverage type hoisting drum 20cm x 20cm, double.  Hoisting drum 25 cm x 33 cm, 700 kg single line, 8 forward, 2 reverse.  Sand reel 20 cm x 55 cm with 21-1/2” clutch, 5500 kb, single line 4 forward, 1 reverse.   Mast hydraulically raised and lowered, equipped with appropriate number of cylinders operated from driller’s station.  It is a telscopic type extendable up to the hieght of 20 meters working clearance with safe lader, money table and drill rod standing provision.  Utility winch, sandline winch, drawworks winch, mechanical type hydraulic system, outriggers and mast tilt, (2) Detroit diesel engines, 7-1/2” x 10” Gardner Denver mud pump (on rig trailer), excellent working condition, currently drilling in Middle East.  Price:  $235,000

Also available:  1200 meters of 3-1/2” drill pipe and collar.

 

GARDNER DENVER DD 2500  (Ref#7587Nb) 

Manufactured 1984, mounted on 3-axle trailer, twin GM 6 cyl diesel engine, single stage mast, 18” rotary table, 7-1/2 x 10” mud pump, 100 joints of 3-1/2”  x 30’ drill pipe, (8) various drill collars, pair of tongs, (2) slips for pipe and collars, drill pipe elevator, (5) various subs, (2) lift subs for drill collars, 6” x 6 meter suction hose 

Price:  $475,000

 

GARDNER DENVER SD55  (Ref#9185N)  Manufactured 1980, drawworks rebuilt 2004, Double drum, Parmac Hydro brake, air clutches, Cummins N14 diesel engine, 56’ x 135,000# mast, racking board, mounted on 4 axle Crane Carrier, (2) Gardner Denver FXO 6 x 10 duplex mud pumps, McKissick 100 ton block/hook, GD 100 ton swivel, 30’ fluted Kelly, Howard Turner 18” rotary table, 4-1/2” x 30’ round fluted Kelly, includes pipe truck (no pipe included)  Price:  $480,000  PRICE REDUCED:  $395,000

 

DSM 2000  (Ref#3551N)  Manufactured 1992, 44M DSM drawworks with air clutches, 256-S2 LeRoi air compressor, 5-1/2 x 8 Gardner Denver mud pump, Bean injection pump, 10” retractable DSM rotary table w/5 speed trans., hydraulic holdback, mounted on 1991 Paystar 5000 truck with 325 hp Cummins engine  Price:  $520,000

 

GARDNER DENVER 2000  (Ref#588N)  Manufactured 1977, 58’ derrick with rackinb oard, double drum drawworks with hydromatic brake, dual cathead, 10” retractable rotary table with 5 speed transmission, 5-1/2 x 10” mud ump on deck, mounted on 4 axle Crane Carrier powered by Cummins 4000 with 5 speed transmission w/4 spd aux., 4 hydraulic leveling jacks, hydraulic pulldown, 4-1/2 hex Kelly with 3” swivel and piping, excellent condition  Price:  $325,000

 

GARDNER DENVER 2000 (Ref#2394N)   Manufactured 1977, PTO, mounted on 1977 Kenworth 4 axle carrier with 400 Cummins engine, 5 ½ x 10 mud pump, 58’ mast (no racking board) 6 lines, 18” stationary table, 34’ x 4 ½” square Kelly, 3” king swivel, breakout cylinder, 2 sets of tongs, air clutches, hydraulic pulldown, 4 hydraulic leveling jacks     Price: $250,000  

1200’ pipe available at additional cost

 

GARDNER DENVER 2000  (Ref#580Na)  Manufactured 1976, 7-1/2 x 10 FXO mud pump (rebuilt), 3 x 4 Mission charge pump with motor and hydraulic cooler (low hours), mounted on 1976 Crane Carrier with 400 Cummins, PTO (completely rebuilt), air clutches, hydraulic pulldown, 10” Gardner Denver retractable table, 9 speed rotary transmission, hydraulic spinners, 56’ derrick  Price:  $375,000

Available at extra cost:

2000’ of 3-1/2 IF pipe (20’ long) new in 2006, sub, slips and tools

160’ 3-1/2 IF collars (20’ long)

1991 FORD LN9000 PIPE TRUCK  (Ref#580Nb)  300 Cummins, 13 speed, tandem Hendrickson suspension, 24’ flatbed with slide and dolly - $35,000

6-1/2 X 12 IDEAL MUD PUMP  (Ref#580Nc)  mounted on skid trailer with gooseneck, 6V71 Detroit diesel engine - $65,000

1968 KENWORTH WINCH TRUCK  (ref#580Nd)  270 Cummins, 5 and 4 trans., tandem axle, Tulsa winch – $17,000

1977 INTERNATIONAL PAYSTAR 5000 WATER TRUCK  (Ref#580Ne)  8V71 Detroit engine, 13 speed transmission, tandem Hendrickson suspension, 80 bbl vac tank, new vac pump - $30,000

1973 MACK WATER TRUCK  (Ref#580Nf)  Thermadine motor, 5 and 4 trans., tandem Mac suspension, 80 bbl vac tank, and vac pump - $25,000

Doghouse 2009 H&H 7 x 12 tandem axle

Tool Trailer, 2009 H&H 7 x 12 single axle

 

GARDNER DENVER 2000  (Ref#13622N)  Mounted on 1995 Ford L9000 Aeromax truck with 60 Series Detroit engine, PTO, 58’ mast with racking board, 12” Brewster rotary table, 6” plumbing set up for reverse circulation, excellent condition, no pipe  Price:  $275,000  PRICE REDUCED:  $235,000

Pipe available at extra cost:  1,500’ of 30’ x 4-1/2” IF pin and box

 

GARDNER DENVER 2000  (Ref#241N)  Manufactured 1978, Gardner Denver FY-FXX 7-1/2 x 10” mud pump, Gardner Denver RT-18 rotary table, SW-75 Ton Gardner Denver Swivel, twin disc air clutches, double drum 45,000# capacity (6 lines) 5/8” cable, mounted on 1980 4-axle Crane Carrier with Cummins 350,  4 leveling jacks, 58’ x 65,000 mast, located Mexico  Price delivered to Texas border:  $280,000

 

GARDNER DENVER 2000  (Ref#8733N)  Gardner Denver FY-FXD 7-1/2 x 10” mud pump, 18” Gardner Denver RT-18 rotary table, double drum drawworks 45,000# capacity with 6 lines, 4 leveling jacks, 58’ x 66,000# capacity mast, located Mexico  Price, delivered to Texas border  $180,000

 

GARDNER DENVER MAYHEW 2000  (Ref#4974N)  Gardner Denver 2000 double drum drawworks, Cabot right angle gear box, Foster breakout wrench, spinning cathead, Martin Decker weight indicator, mounted on 1975 GMC 9500 tandem axle truck with Detroit 8V71 diesel engine, Fuller 10 speed transmission, 8 hole PTO with hydraulic pump, Fuller 3TA-92 auxiliary transmission, 58’ x 75,000# hydraulically raised mast, 7-1/4 x 10 Gardner Denver FXO duplex mud pump, National J12 swivel, 3-1/2” x 37’ square kelly, Web Wilson type D rotary tongs, 7-3/4” Gardner Denver rotary table, chain pulldown, 6V71 Detroit diesel, Allison 600 torque converter mounted on deck.

36’ tandem axle low boy trailer with 1000 gallon diesel tank, 10 kw 3 phase genertor, air compressor 5 hp electric motor, (2) 85 gallon oil lubsters, (3) storage boxes, spare parts and supplies.

Casing elevators and slips

(1) doghouse 24’L x 98’W with 10 steel lockers, knowledge box and storage area

2000’ of 3-1/2” x 31’ drill pipe with 3-1/2” tool joints

(4) 5-5/8” OD x 28’ long drill collars with 4” full hole

Cleaned and painted

Price:  $275,000  PRICE REDUCED:  $225,000

 

GARDNER DENVER 2000 (Ref#8142N)  Manufactured 1978, 2 mechanical drawworks air clutch, mounted on 4 axle Crane Carrier powered by Cummins 350hp deck engine, 4 hydraulic leveling jacks, one section mast with 2 hydraulic raising cylinders, 6x8 duplex mud pumps, 12” Brewster rotary table, 40 King Swivel, located in Mexico  Price: $200,000 delivered to US border

 

GARDNER DENVER 2000  (Ref#8206N)  Manufactured 1977, 58’ x 75,000# capacity derrick, double 6” wide x 22” dia brakes, twin disc PO214 air clutches (15,000# single line pull), six part line set up, Gardner Denver 18” rotary table, Gardner Denver 5-1/2 x 10” mud pump, sandline drum, hydraulic chain pulldown, 4 hydraulic leveling jacks, mounted on Kenworth 8 v 4 “Twin Steer” chassis powered by Cummins 350 hp engine  Price:  $290,000

 

GARDNER DENVER 2000  (Ref#1945N)  Manufactured 1977, drawworks double 6” wide x 22” diameter brakes, twin disc PO214 air clutches (15,000# single line pull), sandline drum, (2) 6 line McKissick blocks, 4” x 38’ square kelly, 3” King swivel, 5-1/2 x 10 Gardner Denver mud pump, Gardner Denver 18” rotary table, 58’ x 90,000# mast, GD 18” table, air clutches, hydraulic chain pulldown, sandline drum, 38’ kelly, mounted on 1977 Kenworth 8x4 truck (twin steer) with 400 Cummins engine, 4 hyd leveling jacks  Price:  $270,000   Available at extra cost:  900’ of 3-1/2” x 4-1/2” x 30’ drill pipe (3-1/2 IF threads), (3) 6-1/2” x 30’ drill collars

 

GARDNER DENVER 2000 (Ref#6502Ra) Manufactured 1977, 58’ mast, mounted on CCC, 6 lines, 5 ½ x 8 GD mud pump, rebuilt 10” table, Little Giant swivel, weight indicator, 35’ x 5 Ό” Kelly  Price:  $205,000

 

GARDNER DENVER 2000  (Ref#8131N)  Manufactured 1976, Completely Refurbished, new 58’ derrick with new kelly blocks and travelling blocks, racking board, hydromatic, 2 catheads, rebuilt 10” retractable rotary table, 4-1/2” square kelly, 3” swivel, pulldown, (2) 5-1/2 x 10 mud pump, no air, Bean water injection, mounted on 4 axle Crane Carrier with 400 Cummins engine 

Pipe trailer with 80 jts of 31’ bottleneck pipe

900/350 Sullair screw mount skid mounted air compressor

FXO 7-1/4 x 10 mud pump with Detroit diesel engine, skid mounted

1982 Freightliner 100 barrel vacuum truck

1980 Kenworth tractor trailer

Price:  $525,000 

Available at extra cost:  3-1/2” x 30’ drill pipe

 

GARDNER DENVER 2000 (Ref#7837R) trailer mounted with 471 Detroit engine, 58’ derrick, 7 ½ x 8 Gardner Denver mud pump powered by Cat 3145 engine, 10” GD retractable table, Leroi 253S2 air compressor  Price:  $120,000

 

GARDNER DENVER 2000 (Ref#15420A) 

Manufactured 1977, double drum drawworks, 70,000# extended hydraulically raised mast, 10” Gardner Denver retractable table, hydraulic winch lines, hydraulic chain pulldowns,  mounted on 4 axle Crane Carrier with Cummins NTC400 Diesel engine, Fuller RTO 9513 Road Ranger  transmission, 4 hydraulic leveling jacks, 53-GA King swivel, McKissick 100-Ton blocks, no mud pump

Misc Tools & Equipment:

Washington Diverter

7” x 30’L Flowline Diverter

Rausch Spinning Tongs, 3 ½” x 7”

(2) Byron Jackson Rotary Tongs

(2) 7” Casing Elevators

Misc. Hand Tools

Misc. X-over Subs

Hex Kelly

1985 International School Bus Doghouse   

PACKAGE PRICE: $ 156,000

Drill Pipe at extra cost - 2360’ of 3 ½” OD x 20’ drill pipe, 13.30#    Price: $ 16,000

 

GARDNER DENVER 2000 (Ref#2394N) Manufactured 1977, PTO, mounted on 1977 Kenworth 4 axle carrier with 400 Cummins engine, 5 ½ x 10 mud pump, 58’ mast (no racking board) 6 lines, 18” stationary table, 34’ x 4 ½” square Kelly, 3” king swivel, breakout cylinder, 2 sets of tongs, air clutches, hydraulic pulldown, 4 hydraulic leveling jacks    Price:  $250,000

1200 pipe available at additional cost

 

GARDNER DENVER 15W (Ref#5095N) modified to GD 2000, set up for deephole drilling, manufactured 1974, mounted on 4 axle crane carrier with 400 Big Cam Cummins engine, 4 line drawworks, 4 ½” x 24’ Kelly, hydraulic pulldown, air clutches, 85000# hook load modified king swivel, 1000’ of 3 ½” IF x 20’ drill pipe  Price:  $320,000

 

GARDNER DENVER SD-55  (Ref#1424N)  Manufactured 1980 (rebuilt 2004), double drum drawworks, depth range 3500’ with 4-1/2” drill pipe, air clutches, double brake bands, 56’ x 135,000# hydraulically raised mast with racking board, mounted on 4 axle Crane Carrier powered by Cumins N14 diesel engine, 4 hydraulic leveling jacks, (2) Gardner Denver FXO 6 x 10” duplex mud pump powered by rig engine, 4” centrifugal charge pump powered by Isuzu diesel engine, Parmac Hydromatic brake, Perkins generator, Foster catheads, McKissick 100 ton block/hook combo, GD 100 ton swivel, Howard Turner 18” rotary table, weight indicator, (2) 100 gallon fuel tanks, 4-1/2” x 30’ round fluted kelly, 5-1/4” x 40’ hex kelly, (2) 3-sheave travelling blocks, BJ tongs, slips and elevators for 4-1/2” drill pipe, bit subs, 7” diverter, suction hose, 5-1/2 and 7” casing tools, 2700’ of 4-1/2” drill pipe, (300) 6” OD drill collars, hydraulic casing spinner, rig lights, misc tools, hoses, fittings, subs, etc., Freightliner doghouse tooled out w/Geolograph 2-pen recorder, cutting torch and welder, International pipe truck  Price:  $375,000

 

GARDNER DENVER SD-55 (Ref#15420C)  Manufactured 1981, double drum drawworks, 121 hydramatic brake, 5/8” drilling line, sandline drum, 18” rotary table, Gardner Denver 3” water swivel, 90,000# hydraulically raised mast, 2” pulldown chain, PTO, hydraulic holdback system, 40 ton swivel, fluted kelly bar, mounted on Crane Carrier w/350 Cummins diesel engine, 5 speed transmission, 4 hydraulic leveling jacks

Price: $ 350,000

Misc Tools & Equipment:

Washington Diverter

Rausch Spinning Tongs

(2) Bit Breakers

(2) Break out Tongs

(2) 3 ½” DP Slips

5 ½” Slips & Elevators

7” Slips & Elevators

Drill Collar Slips

Price for misc tools and equipment: $ 20,000

Drill Pipe -  3800’ of 3 ½”” OD x 20’L drill pipe, 13.30#      Price: $ 38,000

Drill Collars - (5) 6” OD x 20’L Spiral Drill Collars, 4 ½” x H    Price: $ 8,500

                       (2) 6” OD x 30’L Spiral Drill Collars, 4 ½” x H    Price: $ 6,500

 

GARDNER DENVER 1500W H.D.  (Ref#1281N)  rebuilt 10” retractable table, sandline, new kelly 3-1/2” x 23’, new Little Giant swivel, all air clutches, hydraulic pulldown, Bean water injection, oil injection, 750/250 air compressor, piston 5 x 6-1/4”  FM45 mud pump, new Cummins diesel 350 hp, 13 speed Road Ranger transmission, mounted on Crane Carrier, hydraulic jacks, 90% tires, air dryer, 4-1/2” x 20’ pipe, like new  Price:  $145,000

 

GARDNER DENVER 1500 (Ref#12915N) mounted on ’98 Ford L9000 with Cat engine, 7 ½” retractable table, 300cfm air compressor, 38’ mast, 7 ½ x 8 mud pump, 3 hydraulic leveling jacks   Price:  $140,000

 

GARDNER DENVER 1500 WHP (Ref#4602Nb) Manufactured 1973, mounted on 4 axle carrier with 400 Cummins engine with low hours, 10” retractable table, WEJ air compressor, (2) 5 x 6 mud pumps, new sandline, 5” x 24’ Kelly, hydraulic pulldown, 2 ½” swivel  Price:  $200,000

 

GARDNER DENVER 1500  (Ref#7107Nc)  Mounted on 1979 Ford tandem Axle truck, powered by Cat 3208 diesel engine, rebuilt 13 speed Road Ranger transmission, PTO, good drawworks and air clutch, 10” rotary table, 5-1/2” x 8” Gardner Denver duplex mud pump, mast collapsed and destroyed the mast and cab.  Price “as is”:  $85,000  (photo attached is rig before damaged)

 

GARDNER DENVER 1500  (Ref#405N)  Manufactured 1977, WEH 650/150 air compressor, mounted on 1977 Mack D700 truck with 330 Mack diesel engine, 5-1/2 x 8 Gardner Denver mud pump, Bean injection pump, 7-1/2” GD retractable rotary table (rebuilt), hydraulic pulldown, breakout tongs, 200’ of 2-7/8” pipe (2-3/8 IF), currently drilling  Price:  $120,000

 

GARDNER DENVER 1500  (Ref#4183Na)  Manufactured 1978, mounted on 1978 Mack RL700 truck with 400 Cummins engine, PTO, 54’3” square tubed derrick (new), new drawworks, 10” retractable table, WEJ 750/350 compressor, Bean water injection, pulldown, air clutches, 4 hyd levleing jacks, good conditon, well maintained 

Price:  $170,000

Available at extra cost:

7-1/2 x 10” GARDNER DENVER FXO MUD PUMP  (Ref#4183Nb)  Detroit 6V92T engine, mounted on pintle hitch trailer - $45,000

1972 Mack RL700 Pipe trick (Ref#4183Nc)  80 jts of 20’ x 3-1/2” bottleneck pipe

Vacuum truck, doghouse, generator, etc

Package Price:  $310,000

 

GARDNER DENVER 1400  (Ref#14568N) Manufactured 1980, 5 x 6 Gardner Denver mud pump, Gardner Denver air compressor, 7-1/2” retractable rotary table, 30,000# pulldown, 24’ x 3-1/2” kelly, mounted on 1979 Mack Five Star General truck, 292 Cummins engine, PTO, 320’ of 3-1/2” drill pipe, good condition  Price:  $140,000  OFF MARKET

 

SEISMIC RIG (Ref#7391N)  580/50 Gardner Denver air compressor, 5 x 6 Whealey pump,  mounted on 1980 GMC truck with 671 Detroit diesel engine, PTO, 500’ drill pipe  Price:  $85,000

 

DSM (MAYHEW) 1300 (Ref#6660N)  Manufactured 1982, New drawworks, new swivel, new clutches, new transfer case, 5 x 6 Gardner Denver mud pump, IR 185 cfm developmental air compressor, 23’ x 2-7/8” fluted kelly, 25,000# pulldown, new power swivel, mechanical clutches, 7-1/2” stationary table, mounted on 1985 GMC Brigadier truck with 210 Cummins, PTO, 9 speed transmission, air brakes, 2 rear hydraulic leveling jacks, rod box, 600’ of 2-7/8” x 20’ (2-3/8” conn) drill pipe, some tools, good condition, currently drilling  Price:  $130,000

 

GARDNER DENVER 1000  (Ref#4392N)  1400 derrick, 1000 drawworks, PTO, 3-1/2 x 23’ kelly, Gardner Denver 667 air compressor, 5 x 6 Gardner Denver mud pump, 7-1/2” retractale tale, mounted on 1980 International truck with DT466 diesel engine, mechanical clutches, 3 jacks  Price:  $70,000

 

MAYHEW 1000  (Ref#4588N)  Manufactured 1970, rebuilt 2010, 2” Little Giant swivel, 5 x 6 Gardner Denver mud pump (belt driven), LeRoi air compressor, 7-1/2” stationary rotary table (new 2000), drawworks rebuilt 2010, mounted on 1994 Kenworth with Cummins diesel engine, hydraulic pulldown, mechanical clutches, 200’ of 2-7/8” x 20’ Mayhew reg., 100’ 2-3/8” x 20’ Mayhew reg  Price:  $80,000

 

MAYHEW 1000 (Ref#8805Nb) Manufactured late 1970’s, mounted on 2000 International with DT466 engine, fully refurbished, new drawworks, rebuilt mud pump, etc. 5 x6 Gardner Denver mud pump, hydraulic pulldown, mechanical clutches, breakout wrench, pipe rack, 6” Kelly, 200’ pipe   Price on request

 

GARDNER DENVER 1000 HD (Ref#9423Na) Manufactured 1974, Spicer PTO, mounted on International Eagle with 400 Cummins engine, heavy mast, 5x6 Gardner Denver mud pump, 256 Leroi air compressor, 7 ½” retractable table, hydraulic pulldown, Bean water injection, 300’ drill pipe, 3 hydraulic leveling jacks, some tools  Price:  $95,000

 

GARDNER DENVER 1000 (Ref#9423Nc) Manufactured 1977, Spicer PTO, mounted on 1977 Ford F8000 with 290 Cummins engine, 5x6 Gardner Denver mud pump, 256 Leroi air compressor, 7 ½” retractable table, planetary pulldown, Bean water injection, 300’ drill pipe, 3 hydraulic leveling jacks, some tools  Price:  $105,000

 

GARDNER DENVER 1000  (Ref#3178N)  top drive head, no mud, 600/125 air compressor, (table drive missing), mounted on 1983 Mack truck with 6V71 Detroit diesel, 4 jacks  Price:  $50,000

 

GARDNER DENVER 1000  (Ref#1756N)  Manufactured 1981, 5 x 6 Gardner Denver mud ump, 7-1/2” retractable table, 1000 drawworks, Isuzu 6BDDIT diesel on deck, mounted on 1994 Freightliner FL80 truck with 8.3 Cummins diesel engine, hydraulic pulldown, 23’ kelly, WCQ 427 air compressor, 3 jacks  Price:  $95,000

 

GARDNER DENVER 1000  (Ref#2000N)  Manufactured 1980, mounted on Ford LT9000 with Detroit 6V92 engine, 5 x 6 Gardner Denver mud pump, 256 LeRoi air compressor, 10 speed rotary, 2000 (5-14”) stationary table, hydraulic pulldown, mechanical clutches, breakout tongs, 23’ kelly

1980 INTERNATIONAL WATER TRUCK  DT466 engine, 2600 gallon rectangular tank, toolboxes

Equipment trailer: 800’ pipe, grouter, core barrels, mud pits, etc

Package Price:  $275,000

 

MAYHEW 1000 (Ref#8808N) Badger derrick, mounted on 1984 Peterbilt 359 with Cat 3406 engine, 7 ½” DSM 2000 table, 5 x 6 Gardner Denver mud pump, Leroi 256 SDS2 air compressor, Bean 18gpm water injection pump, good condition, currently drilling  Price:  $190,000  PRICE REDUCED:  $145,000

 

MAYHEW 1000 (Ref#4554N) Manufactured 1981, PTO, mounted on 1981 Ford 9000 with Cat engine, 5x6 mud pump, 5 Ό” retractable table, 20’ Kelly, pulldown, rod rack, no air, breakout wrench, 2 rear hydraulic leveling jacks, 100’ of 2 3/8” IF drill pipe  Price:  $60,000  PRICE REDUCED:  $48,000

 

MAYHEW 1000  (Ref#2176N)  mounted on tandem axle International Fleetstar truck, 250 hp Cummins engine, PTO, 5 x 6 mud pump (all new valves), 450/125 Schramm piston air compressor, 5-1/4 hydraulic retractable table, 3-1/4” x 23’ kelly, hydraulic pulldown, new paint, good running condition  Price:  $55,000

Price with 300’ of 3-1/2” x 20’ pipe:  $58,000

 

MAYHEW 1000 (Ref#4665N) mounted on 1993 International 4000 series with DT466 diesel engine, 5 x 6 mud pump, 300’ Mayhew Jr. drill pipe, ready to go  Price:  $50,000

Available at extra cost:  185 CFM air compressor

 

MAYHEW 1000 (Ref#10021N) mounted on Rio 6x6 with Cat 3306 rebuilt engine, Fuller 10 speed transmission, Gardner Denver 5 x 6 mud pump, Leroi 100s air compressor, 2000 stationary table, 3 ½” x 23’ Kelly, water injection pump, 500 gallon water tank, hydraulic pulldown, mechanical clutches, breakout wrench, 2 rear hydraulic leveling jacks, 200 of 2 7/8” x 20’ drill pipe and International

Kaiser 1500 gallon water truck 6 x 6, no crane, no welder 

Package Price:  $65,000

 

MAYHEW 1000 (Ref#7761N) mounted on 1985 Freightliner with Cummins engine, 5 x 6 Gardner Denver mud pump, no air, 5 ½” stationary table, 3 Ό:” x 22’ Kelly, mechanical clutches, hydraulic pulldown, bits, subs, 2 rear hydraulic leveling jacks, 320’ of  2 7/8” x 20’ drill pipe, good condition, currently drilling  Price:  $65,000

 

MAYHEW 1000 (Ref#9686N) Manufactured 1970’s, mounted on 1990 International with DT466 engine, 5 ½ x 6 mud pump, 7 ½” stationary table, 3 ½” x 23’ Kelly, rebuilt clutches, new drawworks, chain pulldown, no air, 1 front & 2 rear hydraulic leveling jacks, breakout wrench, 350’ of 2 3/8” x 20’ drill pipe, good condition, currently drilling  Price:  $57,000  OFF MARKET

 

MAYHEW 1000 (Ref#289R) PTO, mounted on 1980 International 1800 tandem axle truck with new 404 gas engine, 5 Ό” stationary table, Gardner Denver 5x6 mud pump, hydraulic bailing line mounted on mast, 300’ of 15’ x 2 3/8” drill pipe

Available as package with the following:

1980 International 1700 water truck, 1200 gallon tank

Package Price:  $50,000

 

MAYHEW 1000 (Ref#1001N) PTO, mounted on 1986 GMC Brigadier with Detroit 6V92 engine, 6x6 Wheatley mud pump, hydraulic pulldown, mechanical clutches, 7 ½” stationary table, 3” fluted Kelly, toolbox, pipe rack, 2 rear hydraulic leveling jacks, no pipe or tools available  Price:  $45,000

 

MAYHEW 1000 (Ref#10022N) mounted on 1974 Ford 9000 with 350 Detroit engine, Wheatley 5 x 6 mud pump, Leroi 100s air compressor, 2000 stationary table, 3 ½” x 23’ Kelly, water injection, 2 rear hydraulic leveling jacks, 200’ of 20’ x 2 7/8” drill pipe

1977 International water truck, 2000 gallon flat tank, DT466 engine, toolbox, welder, no crane, no pipe rack & hydraulic trailer with mud system

Package Price:  $80,000

 

MAYHEW 1000 (Ref#9449N) late 1960’s-early 1970’s rig, PTO, mounted on 2000 International with DT466 engine, 5 x 6 mud pump, on board air compressor, mechanical clutches, pulldown, 5 Ό” stationary table, 3 ½” x 18’ fluted Kelly, no breakout wrench, stored inside, new tires, 500’ of 2 3/8” x 15’ drill pipe  Price:  $90,000

 

MAYHEW 1000 (Ref#3108N) Manufactured 1960’s, PTO, mounted on 1980 International with 290 Cummins engine, 5 x 6 Gardner Denver mud pump, 2000 table, fluted Kelly, mechanical clutches, no pulldown, no leveling jacks, 300’ of 2 3/8” x 20’ drill pipe   Price $60,000

 

MAYHEW 1000  (ref#4605N)  5 x 6 Gardner Denver mud pump, mounted on Ford LS8000 truck with new Cat engine, PTO, 5-1/4” stationary table, hydraulic pulldown, 3-1/2” x 23’ fluted kelly, breakout wrench, 2 rear hydraulic leveling jacks, 300’ of “like new” 20’ x 2-3/8” drill pipe.

Includes IR175 compressor with diesel engine on 1984 International Flatbed with DT466 engine, 1000 gallon plastic water tank

Price:  $75,000

Available as complete package with all support equipment and many extras:  $95,000

 

MAYHEW 1000 (Ref#9494N) mounted on ’71 Diamond Rio with diesel engine, 5 x 6 mud pump, Leroi 50S1 air compressor, manual breakout, pulldown, no leveling jacks, pipe rack, 500’ of 2 3/8” x 20’ drill pipe, sitting 5 years  Price:  $50,000

 

MAYHEW 1000  (Ref#1724N)  6 x 6 Wheatly mud pump, mounted on 1984 International 1900 single axle truck with DT 466 engine, PTO, 2000 GD table, 25’ kelly, 32’ derrick, hydraulic pulldowns, mechanical clutches, 3 hyd jacks  Price:  $60,000

 

MAYHEW 1000  (Ref#2951N)  6 x 6 Wheatly mud pump, 667 GD air compressor, mounted on 6 x 6 International 5 ton truck with 270 Cummins, 4 hyd jacks, tools, 1000’ of 2-7/8” x 20’ drill pie and 2-3/8” Failng flush joint pipe  Price for rig only:  $70,000

Longyear 10’ double swivel core barrel w/diamond and carbide core bits (takes 2-1/2” core)

1979 WATER TRUCK 6x6, 3000 gallon water tank (tank needs repair), 270 Cummins engine

1986 FORD F350 4x4 crew cab

Package Price:  $95,000

 

MAYHEW 1000  (Ref#2962N)  Manufactured 1980, mounted on Ford 8000 truck with diesel engine, 5 x 6 Gardner Denver mud pump, 315 LeRoi compressor, 23’ kelly, large boom, 2 rear jacks, rod racks, Little giant swivel, 100’ of 2-3/8 IF Rod  Price:  $170,000  OFF MARKET

 

MAYHEW 1000  (Ref#299N)  5 x 6 Gardner Denver mud pump, 580 GD air compressor, mechanical clutches, 2000 rotary table (stationary), mounted on 1980 International truck with 290 Cummins engine, no jacks, 300’ 2-3/8” pipe  Price for rig only (removed from truck)  $35,000

Price for rig and truck:  $48,500

 

MAYHEW 1000 (Ref#2362N) PTO, mounted on 1971 White Constructor with 290 Cummins engine, 6 x 6 Wheatley mud pump, 580 CFM air compressor, 44’ mast, 36’ Kelly, stationary table, mechanical clutches, pulldown, 1 front 2 rear hydraulic leveling jacks, no breakout wrench, no pipe or tools available  Price:  $50,000

 

MAYHEW 1000  (Ref#4915N)  Manufactured 969, mounted on 1990 International truck, 300 Cummins engine, rig runs off Brownie box (no transfer case), 650/50 air compressor, 5 x 6 mud pump, mechanical pulldown, needs minor work (bearing in mud pump and pulldown transmission)  Price:  $52,500

 

MAYHEW 1000  (Ref#8449Na)  Manufactured 1968, mounted on 1979 International 1700 10 wheeler tandem axle truck, 13 speed transmission, 580/150 air compressor, 5 x 6 mud pump, 3” x 23’ kelly, 5-1/2” stationary table, mechanical clutches, hydraulic pulldown, pipe rack, water tank, new Little Giant swivel, 2 rear hyd leveling jacks, DT466 engine, PTO, subs, good condition, 400’ of 2-7/8” x 20’ drill pipe, 21’6” drill collars   Price:  $60,000  PRICE REDUCED:  $45,000

1979 INTERNATIONAL 1700 WATER TRUCK  (Ref#8449Nb)  2500 gallon water tank, 13 sp transmission, toolboxes, good condition  available at extra cost

 

MAYHEW 1000 (Ref#4146Na) Manufactured 1960’s, mounted on 1996 Mack tandem axle with 300 Mack engine, 5 x 6 GD mud pump, no air, 23’ x 2 7/8” fluted Kelly, mechanical clutches, hydraulic pulldown, 2000 table, breakout wrench, 2 rear hydraulic leveling jacks, 400’ of 2 7/8” x 20’ Mayhew regular pipe  Price:  $45,000

1993 INTERNATIONAL 4900 WATER TRUCK (Ref#4146Nb) 800 gallon flat tank, DT466 engine, pipe racks, toolboxes, aux fuel, no crane or welder  Price:  $9,500

 

MAYHEW 1000  (Ref#15190N)  5 X 6 Wheatley mud pump, mounted on 1975 Ford 8000 truck, 225 hp Cat 3208 diesel engine, PTO, 10.00 x 20 new tires, 3-5/16” x 23’ kelly, 2” Little Giant swivel, 5-1/4” non-retractable table, 3 part line, new ½” 19x7 wire rop, (2) new brakes on drawworks, 4 hydraulic jacks, hydraulic pulldown, 2 lockable tool boxes, new flud end on mud pump, steel mud pan, crown sheaves recently rebushed, rod box, 200’ of 3-1/2” x 20’ (2-3/8 IF) drill pipe, new paint currently drilling  Price:  $70,000

 

MAYHEW 1000 (Ref#6846N) PTO, mounted on 1979 International with DT466 engine, less than 500 miles since inframe overhaul, 7 ½” stationary table, 5x6 Gardner Denver mud pump (less than 20 hrs on gear & fluid end) 23’ x 3 ½” Kelly, 185 cfm Airman compressor, 40000# front winch, mechanical clutches, hydraulic pulldown, breakout wrench, 2 rear hydraulic leveling jacks, good condition, ready to go, no pipe or tools available  Price:  $45,000

 

MAYHEW 1000  (ref#15185N)  mounted on 1980’s Freightliner truck with Cummins engine, PTO, chain pulldown, stationary table, 2 new rims for derrick and leveling jacks, gear box recently redone, mud pump removed, no pipe, running condition  Price:  $35,000

 

MAYHEW 1000  (Ref#1853Na and Nb)  Two available, mounted on Ford L9000 tandem axle truck with 671 Detroit diesel engine, PTO, 23’ kelly and kelly bushing.  1 rig has 5 x 6 Gardner Denver duplex mud pump, 1 rig has 4 x 3 centrifugal pump, 200’ drill pipe  Price for both:  $120,000

 

MAYHEW 1000  (Ref#3570N)  mounted on 1984 International 1900 Series, DT466 diesel engine, 3 hyd jacks, mud pump, 2000 table, drill rods, runs good  Price:  $60,000

 

MAYHEW 1000  (ref#9000N)  mounted on 1994 tandem axle Ford L9000 truck, 600/250 WAJ air compressor, LT10 Cummins (290 hp), 5 x 6 Gardner Denver mud pump, 5 speed rotary table, 360’ drill pipe, new kelly, swivel, 5-1/2” stationary table, 2-7/8” x 23’ kelly, Little Giant swivel, mechanical clutches, hydraulic pulldown, 2-7/8 FEDP x 20’ pipe, breakout tongs, bankd new PTO,   Price:  $105,000

 

MAYHEW 1000  (Ref#3245N)  1500 Drawworks, 5 x 6 Gardner Denver mud pump, no air, mounted on 1979 Ford 7000 single axle truck, Cat engine, mechanical clutches, pulldown, 6-1/2” stationary table, 42’ mast, 25’ kelly, 4 hydraulic leveling jacks, breakout wrench, 500’ of 2-7/8 x 20’, currently drilling  OFF MARKET

 

MAYHEW 1000  (Ref#1872N)  mounted on 1971 Mack truck, 9 speed transmission, 2” Little Giant swivel, 231 sq kelly, 5 x 6 mud pump, new DSM 1000 rotary table, 18’ x 7’9” width, 2’ deep water tank, bailer assembly, 3 speed rotary table, 4-1/2” x 20’ drill collar, 200’ of 2-3/8” drill pipe, hydraulic pulldown, 3 line machine, breakout wrench, stationary table, mechanical clutches, 2 manual jacks in rear, pipe racks   Price:  $34,500

 

MAYHEW 1000 (Ref#1790Na) Manufactured 1970, PTO, mounted on 1970 Chevy with gas engine, 5 x 6 Gardner Denver mud pump, 185 CFM on board air compressor with John Deere diesel engine, spudding arm, 5 Ό” stationary table, hydraulic pulldown, 3 hydraulic leveling jacks, 23’ Kelly, 210’ of 2 3/8” x 15’ drill pipe, stabilizer  Price:  $45,000

 

MAYHEW-GARDNER DENVER  (Ref#14354N)  Model 1000  Series Heavy Duty, 580 Gardner Denver air compressor, 5 x 6 mud pump, mounted on tandem axle Mack truck, 285hp Mack diesel engine, hydraulic pulldown, 23’ kelly, 1250 air clutched drawworks, 5-1/2” 1000 rotary table, heavy duty swivel, pipe rack with slide, 2 hydraulic leveling jacks  Price:  $97,000

 

MAYHEW 1000  (ref#2349N)  Mounted on 2000 International truck with DT466 diesel engine, 5 x 6 Gardner Denver mud pump, 5-1/4” stationary table, 18’ kelly, hydraulic pulldown, mechanical clutches, sandline, breakout wrench, 2 rear hydraulic leveling jacks, 190’ of 15’ Mayhew pipe, good condition, currently drilling  Price:  $95,000

 

MAYHEW 1000  (ref#3896Na)  mounted on 1984 Ford F9000 truck with Cummins diesel engine, 627 air compressor, 2 x 3 centrifugal pump, 7-1/2” retractable table, no pulldown, mechanical clutches, pipe wrench, no pipe rack, good condition, currently drilling  Price:  $61,000  PRICE REDUCED:  $50,000

Pipe available at extra cost

 

GARDNER DENVER 1000  (Ref#8303Na)  Manufactured 1970’s, mounted on Paystar 5000 tandem axle truck, 3208 Cat engine, self-dump mud pit, 3rd drum, 500 gal water tank, 5 x 6 mud pump, 250’ of 2-3/8” Mayhew Jr pipe, 3 leveling jacks, 5-3/4” table  Price:  $85,000  OFF MARKET

 

MAYHEW 1000  (Ref#5756N)  mounted on 1980 International tandem axle truck with gas engine, PTO, 5 x 6 mud pump, no air compressor, no water injection, mechanical clutches, hydraulic pulldown, 3-5/8” fluted kelly, 5-1/2” stationary table, breakout wrench,  Price:  $55,000   Pipe available at additional cost

 

GARDNER DENVER 1000 HD  (Ref#1223N)  Manufactured 1978, mounted on 1978 Ford 8000 3-axle truck, 3208 Cat diesel engine, 5+4 transmission, 5 x 6 Gardner Denver mud pump (power end rebuilt with new cross heads and bushings), 500/150 Gardner Denver air compressor,7-1/2” Gardner Denver retractable table, 4 cyl Bean injection pump, IR hammer and 6-3/4” and 8” bits, extra kelly for rig, 1500’ (1020’ Mayhew) of 2-3/8” drill pipe (2-3/8 IF), swviel has new bearings and seals, new chain in chain case, winch on front of rig, duplex tires on front of rig, extra suction hoses and mixing hoses, 50’ new 2” kelly hose, all subs and related drilling equiment new shaker table, 1 drill collar 

1995 Oshkosh 3-axle all wheel drive water truck, powered by L10 Cummins diesel engine, 8 speed transmission with lo/lo, duplex tires on front axle

1995 GMC truck with 3T Smeal pump rig, 5 speed tranmission, elevators

Skid mounted Leroi 256-S2 air compressor with Cummins diesel engine

Package Price:  $235,000

 

MAYHEW 1000  (Ref#1551N)  mounted on 1963 Army 6x6 truck with gas engine, 4-1/2 x 5 mud pump, stationary table, mechanical clutches, hydraulic pulldown, breakout wrench, stabilizer, bits, subs, etc., fully tooled, 3 hydraulic levleing jacks, 450’ Mayhew Jr drill pipe, stabilizer, 7-7/8” bit, paddle bit, currently drilling  Price:  $45,000

 

MAYHEW 1000  (Ref#310N)  Manufactured 1980, no mud pump, 5-1/4” retractable table, mounted on 1980 Ford 9000 tandem axle truck with Cat 3208 Turbo, rod rack, 20’ kelly, 115’ of 2-3/8 IF rod, portable 180 cfm IR air compressor    Price:  $65,000

 

MAYHEW 1000  (Ref#1796N)  mounted on 1995 Chevy Kodiak single axle truck with Cat 3166 engine, PTO (needs to be connected), 5 x 6 Mission mud pump, 4’ kelly, 24’ mast, swivel, 6” stationary table, mechanical clutches, no pulldown, no leveling jacks, 10 jts pipe  Price:  $37,500

 

MAYHEW 1000  (Ref#3993N)  5 x 6 mud pump, developmental air (needs work), mounted on 1967 Ford tandem axle gas engine (needs motor), PTO, 200’ pipe  Price:  $50,000

 

MAYHEW 1000 (Ref#10153N) Manufactured 1972, mounted on 1972 Ford tandem axle truck with 3208 Cat engine, flotation tires on front, 3x2 centrifugal pump (hydrostatic driven) 5 Ό” retractable table,  mounted on a 2’ slide base, Gardner Denver 667 on board air compressor, chain pulldown, mechanical clutches, Mayhew 2” swivel, no breakout wrench, 23 ½” x 3 Ό” square Kelly, fully tooled, 400’ of 2 7/8” x 20’ drill pipe  Price:  $73,000  OFF MARKET

 

MAYHEW 1000  (Ref#7050N)  Manufactured late 1970’s, 427 Gardner Denver air compressor, 6 x 6 Wheatley mud pump, mounted on Chevy truck with gas engine, 2 rear hydraulic leveling jacks, 250-300’ pipe  Price:  $67,000

 

MAYHEW 1000  (Ref#2081N)  5 x 6 Gardner Denver mud pump, 3RD drum, mounted on 1967 International truck w/345 gas engine, 300’ of 2-3/8” x 15’ drill pipe, bits, subs, drill collar, good condition  Price:  $45,000

 

MAYHEW 1000  (Ref#222N)  top head drive, Gardner Denver 5 x 6 mud pump chain driven, LeRoi 450/250 air compressor,  mounted on Ford truck, Cat 3208 engine,320’ of 4-1/2” x 20’ flush wall drill pipe  Price:  $40,000

 

MAYHEW 1000  (Ref#3562N)  580 cfm air compressor, 4 x 5 mud pump, mounted on 1984 Mack tandem axle truck with diesel engine, PTO, 10 gpm Bean water injection pump, chain pulldown, mechanical clutches, 5-1/4” stationary table, 18’ fluted kelly, Little Giant swivel, 2 rear hydraulic jacks, rod rack, mud pit, tools, toolboxes, 300’ of 2-7/8” x 15’ drill pipe, good condition, drills daily  Off Market

 

MAYHEW 1000  (Ref#996Na)  mounted on 1977 International Paystar w/Cummins engine, rebuilt 5 x 6 mud pump, GD 667 air compressor, pulldown, mechanical clutches, new 3-5/16” kelly bar, stationary table, breakout tongs, no leveling jacks, 10-12 jts of Mayhew reg pipe, stored inside, sitting 5 years  OFF MARKET

1981 INTERNATIONAL F SERIES WATER TRUCK  (996Nb) DT466 engine, only 8000 miles, 3000 gallon square tank, toolboxes   OFF MARKET

 

GARDNER DENVER 1000  (Ref#2858N)  1500 Series drawworks with air clutches, 1994 Ford 9000 truck with Cat 3406 rebuilt engine, (2) Gardner Denver 5 x 6 mud pumps, 7-1/2” retractable table, 4 jacks  Price:  $125,000

 

GARDNER DENVER 1000  (Ref#1186N)  Manufactured 1979, Gardner Denver ADL 100/250 air compressor, 8” rebuilt rotary table, 3” x 24’ fluted kelly hydraulic pulldown , mounted on 1978 Ford F8000 tandem axle truck with Cat 3208 engine, 120’ of 3” x 20’ pipe, subs,  Price:  $50,000

 

MAYHEW 1000  (Ref#6211N)  Manufactured 1974, 3 x 4 centrifugal mud pump, mounted on 2001 International truck, International Cat engine, PTO, 6 speed, air brakes, 700’ of pipe, 30’ twoer, (2) 800# drill collars  Price:  $89,000

 

MAYHEW 1000  (Ref#851N)  Manufactured 1956, mounted on International Crane Carrier military 6 wheel drive, Cummins diesel engine, 1000’ of 20’ drill stem, 6 x 6 Wheatly pump, 667 cfm Gardner Denver air compressor.

Includes 1979 International Paystar water truck, 6 wheel drive, 3000 gallon water tank, fully tooled, currently drilling

Package price:  $105,000

 

MAYHEW 1000  (Ref#4333N)  diesel deck engine, 5 x 6 Gardner Denver mud pump, (2) GD 185 air compressors, pulldown, mechanical clutches, 2 rear hydraulic leveling jacks, 225’ of 15’ Mayhew pipe, good condition  Price:  $60,000

 

MAYHEW 1000  (Ref#14620)  Manufactured 1987, mounted on 1987 International truck, 5 x 6 mud pump, drill line.

Also an auger drill mounted on 1975 Ford truck.  Price:  $220,000 for both  OFF MARKET

 

MAYHEW 1000  (Ref#14306)  5 x 6 Gardner Denver mud pump, 7-1/2” non-retractable table, 2-1/2” Little Giant swivel, mechanical clutches, 2 winches, 4 leveling jacks, breakout wrench, tools, mounted on 5 ton Mack tandem axle truck with 300 Mack diesel engine, 500’ of 2-7/8” x 20’ drill pipe, 3-1/2” drill collar, air controled pump clutch, air foot throttle, bit, subs, currently drilling, completely refurbished, 3-1/2” x 23’  fluted kelly  Price:  $110,000  PRICE REDUCED:  $90,000

 

MAYHEW 1000  (Ref#14266)  mounted on 1966 Ford triaxle truck with 250 Cummins engine, 5 x 6 Gardner Denver mud pump, GD 200 PSI air compressor, 5-1/4” stationary tble, 3-1/4” x 24’ kelly, 32’ mast, 2” swiel, hydraulic jacks, 300’ 3-1/4” x 20’ extra heavy duty drill pipe, tools  Price:  $40,000

 

MAYHEW 1000  (Ref#14017)  Manufactured 1960, mounted on 1992 Ford FT900 truck, 5 x 6 mud pump, 25’ mast, 2 rear leveling jacks  Price:  $48,000

 

MAYHEW 1000  (Ref#14031)  5 x 6 Gardner Denver mud pump, GD 667 air compressor, mounted on 1994 International tandem axle truck with 300 Cummins engine, Moyno pump, hydraulic pulldown, mechanical clutches, 18’ kelly, 25’ derrick, retractable table, 4 jacks, 400’ of 2-7/8” x 15’ drill pipe, breakout tongs, excellent condition  Price:  $110,000

 

MAYHEW 1000  (Ref#13392)  Mounted on 1979 Ford truck, 5 x 6 piston pump, 3 x 4 centrifugal pump, 360’ drill rod, 23’ kelly, 5-1/4” table, clean rig, good shape  Off Market

 

MAYHEW 1000  (Ref#1830Nb)  Gardner Denver 667 air compressor, 3 x 2 centrifugal pump, 5-1/4” retractable table, 23’ x 3-1/2” square kelly, pulldown, mechanical clutches, mounted on 1972 Ford F8000 truck with Cat 3208 engine, PTO, 400’ of 2-3/8” x 20’ drill pipe, 3 hyd leveling jacks, good condition, currently drilling  Price:  $75,000

1987 FORD 700 WATER TRUCK  (Ref#1830Nb) 1200 gallon flat tank, 6.6 Ford diesel engine, underbody toolboxes  Price:  $22,000

 

MAYHEW 1000  (Ref#13230)  mounted on 1963 White Crane Carrier with 220 Cummins 6 cyl diesel engine, 200 cfm air compressor, 5 x6 Wheatley mud pump, 17’ kelly, 2” swivel, 5-1/2” stationary table, hydraulic pulldown, 1 front 2 rear hyd leveling jacks, tooling, 200’ of 2-3/8” x 15’ drill pipe, good condition  Price:  $31,000

 

MAYHEW 1000  (Ref#1275N)  mounted on 1974 White Western Star truck with Detroit engine, 5 x 6 mud pump, Gardner Denver big air compressor, stationary table, pulldown, mechanical clutches, many tools and extras, no jacks, 700’ drill pipe  Price:  $40,000

 

MAYHEW 1000  (Ref#14378)  Manufactured 1963, Failing 4 x 5 mud pump (rebuilt with new pistons, liners and rods), gas/propane deck engine, mounted on 1963 Chevy truck, 327 V8 propane engine, drill collars, subs, etc., 250’ of 2-7/8” x 15’ pipe, 200’ of 2-7/8” x 20’ pipe, ready drill drill.  1967 International water truck w/tag axle, V8 gas, 2500 gallon round steel tank (needs work)    Package price:  $32,500

2 axle pipe trailer at additional cost

 

MAYHEW 1000 (Ref#2054N) Manufactured 1970’s, PTO, mounted on 1990 Ford 9000 tandem axle with 7.8 liter diesel engine, air brakes, new tires, rebuilt drawworks, new chains, cable, Kelly, etc, 5 x 6 mud pump, developmental air compressor, 23’ Kelly, mechanical clutches, chain pulldown, breakout wrench, 4 hydraulic leveling jacks, good condition, currently drilling, no pipe  Price:  $100,000

 

GARDNER DENVER 1000  (Ref#10245a)  Manufactured 1970’s, 20 rigs available, incomplete, unmounted, were used for seismic work.  667 air compressor 500/125, room for pump (no pump), 22’ mast, pipe slide, uses 15’ drill pipe, chain pulldown, rotary table, kelly   Price “as is”:  $20,000 - $28,000   

 

GARDNER DENVER TOP DRIVE SEISMIC RIGS  (Ref#10245Nb)  5 available, unmounted  Price:  $40,000 each

 

MAYHEW 1000  (Ref#14841)  5 x 6 mud pump, 350 cfm air compressor, 7-1/2” stationary table, 23’ kelly, pulldown, breakout wrench, mechanical clutches, mounted on 1980 Ford F800 truck with 429 gas engine, 3 leveling jacks, 150’ of 20’ drill pipe, some tools, needs swivel, sitting 3 years  Price:  $35,000

 

MAYHEW 1000  (Ref#11057)  converted to 1250 drawworks, brand new break bands, air clutches, 2 lines (sandline and kelly line),  Badger 32’ mast, 7-1/2 non-retractable Gardner Denver 7003A rotary table (rebuilt), hydraulic pulldown assembly, Little Giant swivel, 23’ kelly, 256-S2 LeRoi air compressor, 5 x 6-1/2” Failing mud pump, newly rebuilt fluid and power ends April 2009, mounted on 1978 Ford 900 tandem axle truck with 350 hp Cummins diesel (rebuilt), 3 hydraulic leveling jacks,  new tires, floatation tires on front, 3 speed rotary transmission, 3 hydraulic leveling jacks, subs, 200’ 2-7/8” drill pipe.   Items rebuilt:  kelly, swivel, new bushings, new pulldown chains, drive line, transfer case, clutches  etc.  200’ of 2-7/8” IF x 20’ drill pipe (2-3/8 box and pin)  Currently Drilling.  Excellent condition.  Set of tracks included   Price:  $125,000

 

GARDNER DENVER 1000  (Ref#15443)  mounted on 1981 International 1800 truck with DT466 diesel engine, 7-1/2” stationary table, pulldown, mechanical clutches, 5 x 6 mud pump, LeRoi air compressor, 2000 cable, 23’ kelly, 4 hyd leveling jacks, good condition  Price:  $65,000

 

MAYHEW 1000  (Ref#10929)  1970’s, double drum, 5-1/2” GD stationary table, 4-1/2 x 5 GD mud pump, mounted on 1979 International truck with Cat 3208 diesel engine, 2 rear hyd leveling jacks, rod rack, new pulldown chains, shafts and bearings, rebuilt swivel. 300’ of 15’ Mayhew pipe (some 2-3/8, some 2-7/8) slips for both, currently drilling, good condition 

Includes 1984 Ingersoll Rand 185 air compressor trailer mounted and 1986 Ford F700 with new 2000 gal water tank and rod racks.  Package Price:  $57,500

 

MAYHEW 1000  (Ref#10897)  18’ kelly, hydraulic pulldown, 5 x 6 Gardner Denver mud pump, rebuilt 5-1/2 table, mounted on 1978 Ford 8000 tandem, 3 leveling jacks  Off Market 4/07

 

MAYHEW 1000  (Ref#1014N)  Manufactured 1952, mounted on 1968 Ford single axle truck, boom was originally 15’, extended to 20’, 23’ square kelly, 4-1/2 x 5” mud pump, no air  POR

 

MAYHEW 1000  (Ref#1015N)  Manufactured 1968, mounted on tandem axle International, pulldown, 23’ fluted kelly, large turntable, 20’ boom, no air  POR

 

MAYHEW 1000  (Ref#8095)  Manufactured 1971, 250/100 air compressor, 5 x 6 Gardner Denver mud pump, mounted on 1962 Ford with Ford V8 engine, Miller generator, jacks, tools, bits, fair condition, located Central America  Price:  $52,500

 

MAYHEW 1000 (Ref#5115)  Manufactured 1970, new 24’ kelly, new 2” swivel, 6” rotary table, 5 x 6 GD mud pump, rebuilt low pressure air compressor, sub, mounted on 1974 International truck with 290 Cummins diesel.  And 1974 White water truck.   Off Market 4/07

 

MAYHEW 1000  (Ref#8225)  1968, 4 x 5 Mission centrifugal pump, 5-1/4 set table, manual pulldown, 300’ drill pipe, 4 hyd jacks, new shaft in mud pump, new gooseneck at swivel, on 1984 Mack Superliner with 350 Mack engine  Price:  $54,500

 

MAYHEW 1000  (Ref#10879)  (2) 5 x 6 mud pumps, GD 427 developmental air compressor, 5-1/4” non-retractable table, mounted on 1984 Freightliner with 400 Cummins, 400’ drill stem  Price:  $75,000

 

MAYHEW 1000  (Ref#8715N)  Mounted on NODWELL 110 tracked carrier, 504 Cummins diesel engine, 32’ derrick, wireline winch, Gardner Denver WCG 580/50 air compressor, Gardner Denver 5 x 6 mud pump, hydraulic pulldown, rebuilt rotary table, some pipe and tools, good condition  Price:  $80,000  PRICE REDUCED:  $60,000

 

MAYHEW 1000  (Ref#7337N)  mounted on Cat D7 crawler with gas pony motor, 8’ wide w/4 sp manual transmission, 22” width tracks, Gardner Denver 580 air compressor (low pressure high volume), Bean water injection pump (12-15 gpm), 200 gallon water tank, Mayhew 1000 5-1/8” stationary table, 3 speed rotary transmission, 2” Mayhew swivel, double drum drawworks, 23’ fluted kelly, hydraulic pulldown with 4 speed transmission, mechanical clutches, breakout wrench, rod rack, 140’ of 2-3/8” x 20’ drill pipe, ready to go 

1976 International water truck, 1500 gallon, International 555 diesel engine, no crane, no welder

Package Price: $50,000

 

MAYHEW 1000  (Ref#3570N)  mounted on 1984 International 1900 Series truck, DT466 diesel engine, 3 hydraulic jacks, mud pump, 2000 table, drill rods, run goods  Price:  $65,000

 

MAYHEW 1000 (Ref#4786N) mounted on a 1978 Scott, 4 ½ x 6 Gardner Denver mud pump, completely overhauled, 2 7/8” IF x 10’ rods  Price:  $$40,000 Canadian

 

MAYHEW 1000  (Ref#227N)   mounted on 1955 International Red Diamond truck, 6 cyl engine, 4-1/2 x 6 mud pump, 300’ drill pipe, sitting 4-5 years  Price:  $15,000

 

MAYHEW 800 (Ref#8805NA) Manufactured 1970’s, mounted on 1995 Ford with diesel engine, 5 x 6 Gardner Denver mud pump, hydraulic pulldown, mechanical clutches, stationary table, breakout wrench, 6” Kelly, pipe rack, 3 hydraulic leveling jacks, 200’ pipe   Price on request

 

GARDNER DENVER 500  (Ref#14014)  Manufactured 1989, mounted on Intetrnational 4700  4 x 4 truck with diesel engine, 5 x 6 Gardner Denver mud pump, 427 air compressor, 2 rear leveling jacks, 25’ mast, good condition  Price:  $80,000

 

GARDNER DENVER 500  (Ref#3127N)  5 x 6 Gardner Denver mud pump, GD 80L developmental air, Isuzu 4 cylinder on deck, 5-1/4” retractable table, 23’ kelly, 500 drawworks, Little Giant swivel, mounted on 1985 International with DT466 diesel engine, mechanical clutches, pulldown, 3 jacks, currently drilling, 200’ of 3” x 15’ with 2-3/8 IF pipe  Price:  $70,000

 

GARDNER DENVER 500  (Ref#2998N)  5 x 6 Gardner Denver mud pump (gear end rebuilt), 580 air compressor, 5-1/4” rotary table retractable, 20’ derrick, 23’ kelly, mounted on 1997 International single axle truck with diesel engine, twin screw clutches, 3 jacks  Price:  $45,000

 

GARDNER DENVER 500  (Ref#1210N)  Isuzu diesel deck engine, mounted on 1990 International 4900 tandem axle truck with DT466 engine, 250/79 air compressor, 5x6 mud pump, hydraulic pulldown, mechanical clutches, 23’ kelly, 2” Little Giant swivel, 5-1/4” retractable table, 3 hydraulic leveling jacks, 180’ of 3-7/8” x 15’ drill pipe, good condition, currently drilling  Price:  $75,000

 

GARDNER DENVER 500  (Ref#15357)  Manufactured 1981, 4-1/2 x 5” Gardner Denver pump, 427 air compressor, mounted on 1981 6x6 Ford w/8.2 liter fuel pincher, 3 hyd jacks, 25’ mast, 18’ fluted kelly, low hours  Price:  $70,000

 

GARDNER DENVER 500   (Ref#2020N) Manufactured 1980, PTO, mounted on International single axle truck with DT 466 engine, 5 x 6 mud pump, no air, chain pulldown, mechanical clutches, 23’ Kelly, breakout wrench, 200’ of 2 7/8” x 15’ drill pipe. Good condition, drilling now  Price:  $60,000  OFF MARKET

 

GARDNER DENVER 500  (Ref#2833N)  Manufactured 1980’s, 5 x 6 mud pump, developmental air, retractable table, mounted on 1994 Ford truck with Cummins engine,PTO, hydraulic jacks, 80% tires, 25’ kelly bar, 200’ of 2-7/8” x 20’ drill pipe  Price:  $84,000

 

GARDNER DENVER 500  (Ref#15353)  Manufactured 1979, completely refurbished, rebuilt swivel, rebuilt 5x6 mud pump, GD 300/150 air compressor, approx 6”” retractable table, breakout wrench, 32’ mast, 23’ x 3” kelly, air clutches, hydraulic pulldown, 140# auto hammer, sandline, cathead, generator, mounted on 1979 International tandem axle truck (cab needs electrical work) with new 300 Cummins engine (4 years left on warranty), new clutch, bearings, complete rebuilt transfer case, PTO, 3 leveling jacks, bits, 4” x 15’ bailer, stem, mud box, mud mixer, wrenches, casing elevators, etc., 450’ od 2-3/8” Mayhew pipe, all tools, complete package.  Truck has had fire damage, gauges not working.

Package Price:  $100,000  PRICE REDUCED:  $63,000

GMC 3500 WATER TRUCK  (Ref#15353b)  1680 gallon fiberglass water tank, propane, extra storage tank, no crane, no welder  - available at extra cost

 

GARDNER DENVER 500  (Ref#514N)  Mid 1970’s, mounted on 1978 Ford 4 wheel drive truck, Ford engine, 60 cfm air compressor, 4-1/2 x 5 Failing mud pump, 300’ pipe, bits, drill collars  Price:  $65,000

 

MAYHEW 500 (upgraded from 250) (Ref#6181N) Detroit 471 deck engine, mounted on 1984 Chevy C60 with 350 gas engine, 5 Ό” stationary table, new drawworks, friction clutches, etc. pulldown, portable mud pit, 400’ of 2 /38” upset tubing drill pipe  Price:  $37,000

 

MAYHEW 500 (Ref#4212Na) PTO, mounted on 1990 GMC with Cat engine, 4 x 5 mud pump, 250 cfm on board air compressor, 20’ Kelly, 5” stationary table, mechanical clutches, pulldown (not hydraulic), breakout wrench, 2 rear hydraulic leveling jacks, 350’ of 15’ x 2 7/8” drill pipe   Price:  $49,000  OFF MARKET

 

MAYHEW 500  (Ref#2781N)  mounted on 1984 Chevy truck with diesel engine, 7-1/4” stationary table, 3-7/8” kelly, rebuilt 4-1/2 x 5 mud pump, pulldown, 2 rear hyd leveling jacks, good condition, ready to go (no pipe or tools available)  Price:  $40,000 

 

MAYHEW 500  (Ref#1271N)  Manufactured 1979, on original 1979 Ford F7000 truck, recent new 3208 Cat engine, clutch, rear, springs and tires, 3 lines (sandline, tool line, kelly lines), 3 leveling jacks, 5-1/4” retractable table, 32’ mast, 23’ fluted kelly, 5 x 6 Gardner Denver mud pump, stored inside, 300’ of 2-7/8 IF x 15’ drill pipe, no air, mechanical clutches, pulldown, 3 leveling jacks   Price:  $55,000

 

GARDNER DENVER 500  (Ref#15521N)  Manufactured 1978, mounted on 1978 Ford single axle truck, Cat 3406 engine, PTO, 5 x 6 mud pump, developmental air, retractable table, mechanical clutches, breakout wrench, 23’ kelly, toolboxes, rod rack, homemade on-board grouter w/Moyno grout pump, stabilizer, mud tank w/baffles, 300’ of pipe, hydraulic pulldown, running condition, stored inside, one owner/operator  Price:  $57,000

 

MAYHEW 500  (Ref#14846a)  mounted on 1977 Ford F600 truck with gas engine, 4 wheel drive, water injection, air compressor, winch, 170’ Mayhew Jr. Pipe, good condition

MAYHEW 500  (Ref#14846b)  mounted on 1979 Ford F600 truck with gas engine, 4 wheel drive, winch, 1200 gal water tank, good condition  Price for both:  $50,000

 

GARDNER DENVER 500  (Ref#13403)  Manufactured 1978, 5 x 6 mud pump, 32’ mast, 2” Little Giant swivel, 23’ kelly, 5-1/4” non-retractable table, mounted on 1980 International 4600 single axle truck w/DT466 diesel engine, PTO, chain pulldown, breakout tongs, 3 hyd leveling jacks, 200’ Mayhew Jr 15’ drill pipe, good condition  Price:  $55,000

 

GARDNER DENVER 500  (Ref#8303Nc)  Manufactured 1970’s, mounted on Paystar 5000 truck, Cat 3208 engine, self dump it, 3rd drum, 500 gallon water, 4-1/2 x 5 mud pump, 5” table, 3 leveling jacks, 250’ of 2-3/8 Mayhew Jr  Price:  $85,000  OFF MARKET

 

GARDNER DENVER 500  (Ref#4981N)  Manufactured 1966, mounted on 1995 Ford F800 truck with 8.3 Cummins diesel engine, completely rebuilt Winter 2011, planetary pulldowns, 120 pulldown chains, 4-1/2 x 5 Failing mud pump, developmental air, 6 strand PTO box out of Midway 1500, rebuilt drawworks, new operator’s platform, 4 jacks  Price:  $75,000

 

GARDNER DENVER 500  (Ref#10895)  Manufactured 1958, 18’ kelly, hyd pulldown, 5 x 6 Gardner Denver mud pump, mounted on 1992 International 4800 D.T. 466 diesel engine, 4x4 single axle, 170” sheel base, 3 leveling jacks  Price:  $60,000  OFF MARKET

 

GARDNER DENVER 500  (Ref#11168)  7042 power tower engine, mounted on 1979 Ford F800 with Cat 3208 engine, low hours, truck has 5 speed and 4 speed auxiliary transmission, Wheatley 4-1/2 x 5 mud pump, core extruder, hydraulic hole loader spool, 300’ of 20’ Mayhew Jr. drill pipe, 3 jacks, good condition, ready to drill  Price:  $45,000

 

GARDNER DENVER 500  (Ref#11158Na)  factory mounted on D-4 Caterpillar, 4 hydraulic jacks, 4-1/2 x 5” Gardner Denver mud pump, Gardner Denver 427 cfm air compressor, 13’ kelly, 4-1/2” retractable table, 1-1/2” swivel, good condition, needs paint  Price:  $30,000

Also available: 3 tandem axle trailer, with electric brakes for additional cost

 

MAYHEW 500  (Ref#9421N)  5 x 6” Gardner Denver duplex mud pump, mast for 20’ drill pipe, 5-1/4” Mayhew retractable rotary table, double drum with mechanical clutches, mounted on 6 x 6 all wheel drive AM General 2.5 ton truck with multi-fuel engine (diesel), reconditioned truck., mechanical winch on front of truck.  4 hydraulic leveling jacks, (2) single sheave traveling blocks, 2” Little Giant swivel, 23’ fluted kelly with saver sub back to 2-7/8” IF drill pipe, breakout tong, Murphy fast plug, large 3 part hinged working floor, 26 jonts of 2-3/8 IF conn on 2-7/8” x 20’ drill pipe, subs.

Water truck with 1500 gallon water tank and drill pipe trailer

POR

 

MAYHEW 500 (Ref#948N) Manufactured 1966, mounted on 1978 Ford 7000 with 3208 Cat engine, 4 hyd leveling jacks, 5 Ό” stationary table, 5 x 6 mud pump, 18’ x 3 5/16” round fluted Kelly, pulldown, mechanical clutches, 2” Little Giant swivel, breakout wrench, portable mud pit, 300’ of 2 7/8” x 15’ drill pipe, currently drilling, rebuilt drawworks and mud pump,   Price:  $50,000

 

MAYHEW 200   (Ref#2782N)  mounted on Ford 1 ton truck with new 7.3 liter diesel engine (less than 5000 miles), 4-1/2 x 5 mud pump, 9” stationary table, mechanical clutches, no pulldown, 2 rear hydraulic leveling jacks, 100’ of 2-3/8” x 10’ pipe, rig has been sitting 2 years  Price:  $40,000

 

MAYHEW 200 (Ref#5031N) trailer mounted, Ford diesel engine, in-out slide base, 4x5 Gardner Denver mud pump, 80’ of 2 3/8” x 10’ Mayhew regular pipe  Price:  $45,000

 

MAYHEW 200 (Ref#3602N) Perkins diesel deck engine, mounted on 1985 Ford single axle truck with diesel engine, 4 x 5 mud pump, 20’ Kelly, 4” stationary table, pulldown (not hydraulic) mud tub, mechanical clutches, no breakout wrench, bits, subs, etc. 1 front & 2 rear hydraulic leveling jacks, 400’ of 20’ drill pipe  Price:  $30,000

 

GARDNER DENVER 15W  (Ref#5177N)  Manufactured 1980, mounted on 8 x 4 Hendrickson Crane Carrier, new 400 Cummins in 2004, 5-1/2 x 8 Gardner Denver mud pump, 50’ mast, 650/250 WEJ air compressor with injection pump, 10” retractable table, new swivel, hydraulic pulldown, air clutches, bailing line, 4-1/2” x 24’ fluted kelly, 4 hyd leveling jacks, good condition, currently drilling  Price:  $250,000

Pipe and tools available at extra cost.

 

GARDNER DENVER 15W  (Ref#5449N)  54’ extended derrick with racking board, 750/300 Sullair screw compressor, 12” rotary table, triple drum drawworks with weight indicator, mounted on 4 axle Crane Carrier, Cat 3406 engine, 10 speed transmission, 3 hydraulic leveling jacks and breakout ram  Price:  $135,000

 

GARDNER DENVER 15W  (Ref#10142N)  51’ mast, 400 Cummins engine with blower, double drum drawworks (kely, traveling blocks, sandline), air clutches and spinning chain, 25’ fluted kelly, 8” retractable Gardner Denver table, 5 x 8 duplex mud pump, 750/250 air compressor, hydraulic pulldowns, 51’ mast with racking board, handles Range 3 casing, stands doubles back in derrick, mounted on truck, 3 hydraulic leveling jacks  Price:  $165,000

 

GARDNER DENVER 15W  (Ref#10014N)  WEJ 750/300 air compressor with cycle blower, Gardner Denver 5-1/2 x 8” duplex mud pump, 10” Gardner Denver retractable table, 33’ x 4-1/2” square kelly, dhree drums (kelly, traveling blocks and sandline, all air clutches and spinning chain, new 53’ square tubed mast with racking board, can handle Range 3 casing, stands doubles back in derrick, mounted on 4 axle Crane Carrier, 4 hydraulic leeling jacks, hydraulic pulldowns, 400 Big Cam Cummins Turbo charges engine  Price:  $185,000  PRICE REDUCED:  $164,000

 

GARDNER DENVER 15W (Ref#2585N)  Manufactured  1965, mounted on 1997 International Paystar 5000 truck with Cat 3406 diesel engine, 5 ½ x 8 mud pump, WEJ air compressor, 10” GD retractable table, 58’ mast, racking board, bailing drum, new 2” Little Giant swivel, hydraulic pulldown, air clutches, 3 hydraulic leveling jacks, 800’ of 2-7/8” x 20’ drill pipe, subs  Price:  $245,000

 

GARDNER DENVER 15W  (Ref#8729N)  Manufactured 1974, 850/250 air compressor, 5-1/2 x 8 mud pump, 58’ mast, 10” retractable table, 400 Cummins diesel engine (3 years old), mounted on Crane Carrier, good running condition  Price:  $245,000

 

GARDNER DENVER 15W  (Ref#6240N)  Manufactured 1974, 650/250 air compressor, 5 x 10 duplex mud pump, cathead, spinning chain, mounted on Crane Carrier with diesel engine, 3 speed transmission  Price:  $135,000

Also available at extra cost: 

1979 Kenworth 4000 gallon water truck 

1962 International pipe truck with 1000’ of 3-1/2” drill pipe, (2) 5” drill collars, (5) 4” dril collars, subs, change over sub

 

GARDNER DENVER 15W  (Ref#191N)  Manufactured 1973, mounted on Crane Carrier, 400 Cummins deck engine, 5 x 6 mud pump (rebuilt 2005), 600/300 WEJ air copressor, 900/125 booster, 8 gpm Bean water injection, 10” Howard Turner retractable table, 56’ mast, racking board, hydraulic pulldown, new shaft for hydraulics, 3 leveling jacks, cyclone blower assembly, 3” swivel, good running condition  Price:  $170,000

980’ of 2-7/8” IF thread flush wall pipe available at extra cost

 

GARDNER DENVER 15W  (Ref#2443N)  Manufactured 1969, 750/250 air compressor, 5 x 6-1/4 FM45 duplex mud pump (new fluid end parts), 10” retractable table, 38’ hydraulically raised mast, mounted on 4 axle Crane Carrier with 350 Cummins diesel engine, reworked, new tires  Price:  $165,000

 

GARDNER DENVER 15W  (Ref#974N)  5-1/2 x 8 mud pump – 100 rpm, Gardner Denver WEJ air compressor with injection pump, 10” Gardner Denver rotary (retractable), 58’ mast, 80,000# capacity DSM style, new racking board DSM style, bailing drum with rebuilt drawworks, new DSM swivel, mounted on Crane Carrier Carrier, factory new 300 Cummins engine, 4 hydraulic jacks, (2) four parts lines, currently working  Price:  $290,000  OFF MARKET

Available with drill rod and collars

 

ARDNER DENVER 5 x 10 DUPLEX MUD PUMP FC-FXD  (Ref#167N)  with 5” liners rated at 276 gpm at 574 psi, mounted on skid, Detroit diesel engine, dampener, complete fluid end parts, good condition  Price:  $36,500

 

GARDNER DENVER 14W  (Ref#11550) 1986, PTO, mounted on Crane Carrier with diesel engine (new 1 year ago with warranty), 11-1/2” retractable table, 5-1/2 x 8 mud pump, 280/800 air compressor (rebuilt), 53’ derrick,

Includes Kenworth tandem axle water truck, pipe trailer, 1500’  2-3/8” pipe, good condition  Price:  $270,000

 

GARDNER DENVER 14W (Ref#2958Na) Manufactured 1976, 53’ mast with racking board,  mounted on Crane Carrier with diesel engine, 5 ½ x 8 mud pump, 9 1/2” retractable table, 4” x 27’ Kelly, hydraulic pulldown, air clutches, 800/260 air compressor, 2 7/8” x 20’ drill pipe  Price, rig only:  $120,000

Also available:

1979 Kenworth water truck (Ref#2958Nb) 80 barrel vac tank, 400 Summins engine, air ride suspension

1964 Autocar water truck (Ref#2958Nc) 100 barrel tank, 350 Cummins engine

2000 Ford F 900 (Ref#2958Nd) pipe truck

2004 Ford F350 crew cab truck (Ref#2958Ne)

Package Price:  $230,000

 

GARDNER DENVER 14W  (Ref#3658)  Manufactured 1972,  5 x 6 Gardner Denver pump (overhauled), 600/250 compressor, 3-1/2" x 23' kelly, 2" swivel, 9" retractable table,  Mounted on Crane Carrier with 300 Cummins, 8 sp R.R., 300' of 2-7/8" x 20’ drill pipe, good condition    Off market