SUN MACHINERY CORP

Telephone: (516) 536 7375 Fax: (516) 536 7317

These rigs are located at various locations through out the USA and Internationally.

Franks

FRANKS WORKOVER RIG (Ref#1011Na) Manufactured 1975, double drum, Franks 42 x 12 drum, mounted on 4 axle carrier powered by 8V71 Detroit diesel engine 315 hp, Allison 750 5-speed transmission, 69’ x 150,000# Skytop stiff mast, 50 ton McKissick block 4 lines, good clean condition Price: $425,000

FRANKS 300 WORKOVER RIG (Ref#1521N) 96’ x 250,000# hydraulically raised mast, double drum, 1287/160 drawworks, hydromatic, mounted on 4 axle Franks 300 carrier powered by Detroit Series 60 diesel engine Price rig only: $425000 Price tooled up: $475,000

FRANKS 42-12 WORKOVER RIG (Ref#2202N) Reworked and recertified in Canada, Manufactured 1975, 750' of drill line, 69' x 150,000# Skytop stiff mast, mounted on 4 axle carrier w/ 8V71 Detroit diesel engine, 750 Allison automatic transmission, 75 ton McKissick 4 line blocks, 3,000# Townsend BOP, Foster 5933 tongs PRICE: $175,000

FRANKS EXPLORER III (Ref#566Nb) Manufactured 1970, double drum, 71’ x 150,000# mast, new Detroit 6V71 diesel engine, new 10 speed transmission, 50 ton McKissick block, tools, currently working, fully refurbished, new engine, all new hydraulics, etc. Price: $210,000

FRANKS EXPLORER III EXPLORER (Ref#833N) Manufactured 1980, double drum, double triple, 9/16” sandline, 7/8 drill line, 50 ton traveling block, 96’ x 180,000# hydraulically raised and scoped mast, outside legs 4” square steel, mounted on 4 axle carrier with 8V71 Detroit diesel, tandem steering and rear ends, 3 speed automatic (Allison 750 transmission available for the rig), 2 leveling jacks in rear, requires some work, painting, hydraulic leaks, air leaks, running rig, Foster hydraulic tubing tongs, air slips, tubing and rod elevators. Price: $200,000

FRANKS EXPLORER III (Ref#883N) 180,000 lb Derrick, Double Triple 96' Derrick, Single Drum Drawworks, Detroit 8V71 w/ Allison, 4 line speed block No swivel, Peckamatic Tongs, Guiberson Double 3000# BOP, Rod & Tubing Elevators & Tools, New 1" Drill Line (560'), New 5/8 Cat Line, New Tong & Rod Lift Line, New Tires, New Drive line , U Joints & Third Member, New Hydraulic Pump w/ Eaton Air Clutches, All new Brake Cans, Tubing Board, New Battery, Starter & Gauges, Most air & hydraulic line has been replaced, Rebuilt Drawworks with all new Clutches, Bladders and Bearings Price for rig only: $450,000 Price with tools: $500,000

FRANKS 44 ROCKET WORKOVER RIG (Ref#507N) Single drum, air over grease clutch, 55’ x 185,000# mast, mounted on 2 axle rear Crane Carrier with 6V71 Detroit diesel, Allison transmission, hydraulic utility winch, 50 ton Wilson block,

2004 Dodge crew truck

New 2008 5893R powertongs and tools

Good working condition

Price: $195,000

FRANKS 44 WORKOVER RIG (Ref#697Na) 4000-5000’ depth, double drum, 10’ x 13’ x 65 winch raised single pole, mounted on 1989 International tandem axle truck with DT466 diesel engine,13 speed transmission, tooled for tubing and rods, tongs, air sprockets, currently working Price: $235,000

FRANKS 844 CRUSIER WORKOVER RIG (Ref#697Nb) single drum, mounted on 1981 GMC Brigadier with diesel engine, 10” x 13” x 65’ winch raised single pole, all tools for tubing and rod, Peck-o-Matic tongs, currently working Price: $145,000

FRANKS 844 (Ref#5607N) double drum, complete Price: $400,000

FRANKS 44x33 WORKOVER RIG (Ref#7204N) 75% completed, requires work, 4500’ depth capacity, 65’ x 125,000# mast, Mounted on Ford L9000 tandem axle truck with Detroit series 60 engine, Manual transmission Price: $130,000

FRANKS 44 DOUBLE DRUM BACK-IN WORKOVER RIG (Ref#15724) double drum, air clutches, working line 7/8”, 54’ x 80,000# hydraulically raised mast with racking board, mounted on tandem axle rear carrier powered by GMC 671 diesel engine, worked 4000’ wells Price: $100,000

FRANKS 44 SERVICE RIG (Ref#15259N) double drum, double pole (2) 8-5/8 x 7” x 60’ poles, 4400’ swabbing, 4000’ workover, 8V71 Detroit on deck, mounted on Mack tandem axle truck with Mack 300 diesel engine, 6 speed transmission, double frame CH613, 40,000# rear end, working rig Price: $125,000

FRANKS 44 DOUBLE DRUM WORKOVER RIG (Ref#1557Nd) mounted on mounted on FL80 Freightliner (super clean, low mileage), 3176 Cat engine, 9 speed transmission, Franks 250 hp drop box, tubing drum, straight air, sandline, air over grease, 10x13 pole, hydraulic leveling jacks, aux winch, drawworks 81 model, new chains and roller, rig never used since completely gone through Price: $180,000

FRANKS 44 WORKOVER RIG (Ref#1557Ng) mounted on 1991 Mack truck with Mack engine, Detroit 471 deck engine w/8 speed transmission, Wilson sandline, 8 x 10 poles, leveling jacks, air controls Price: $100,000

FRANKS 44 WORKOVER RIG (Ref#1557Nk) mounted on 1994 Volvo truck with Cummins engine, 9 speed trans., Franks 250 hp drop box, 3000’ 9/16” sandline, 8 x 10 pole,, leveling jacks, hydraulic winch Price: $145,000

FRANKS 42-12 WORKOVER RIG (Ref#13090Na) Manufactured 1975, 69’ Skytop stiff mast x 150,000# derrick, class 2 free standing single, 8V71 Detroit engine, mounted on 4 axle carrier Price: $170,000

FRANKS 33 DOUBLE DRUM WORKOVER RIG (Ref#1557Nc) mounted on 2000 Sterling truck with Cat power, 9 speed transmission, Franks drop box, 8 x 10 pole, new inner pole, leveling jacks, 2000’ of 9/16” sandline Price: $100,000

FRANKS 33 SINGLE DRUM WORKOVER RIG (Ref#1557Nf) mounted on International truck with V8 International diesel engine, Allison auto transmission, Franks drop box 33 SD franks, 8 x 10 pole, hydraulic leveling jacks Price: $65,000

FRANKS 1287-120 (Ref#7879N) All Franks, All Original, Double drum, manufactured 1967, 96’ x 180,000# mast, Allison 4460 transmission, 8V71 Detroit engine, 15” double Hydrotarder, 760’ of 7/8” drill line, 12,000’ of 9/16” sandline, hydraulic leveling jacks, hydraulic scoped, 100 ton 4-sheave block, rod board, tubing board, mats, 4 axle Franks carrier, tooled out (Foster 5893 tongs, elevators, elevators links, Cavin B air slips, weight indicator), worked six months ago Price: $460,000

FRANKS 1058 DOUBLE DRUM WORKOVER RIG (Ref#1291N) double drum, 8,000’ depth capacity, tri-scope double/triple mast 150,000#, mounted on 4 axle carrier powered by Detroit Series 60 diesel engine, 5860 Allison transmission, drop box (200 hours), 300 hp right angle box, 75 ton McKissick traveling blocks, BJ power tubing tongs, Guiberson 100 ton air slips, (2) sets of 100 ton tubing elevators, 72” 100 ton elevator bales, swab lubricator and pump, swab mandrels Price: $335,000

FRANKS 1058 WORKOVER RIG (Ref#280N) Franks 1058-120 double drum drawworks, 71’ x 150,000# telescopicing Corsair derrick, single/double, 8V71 Detroit diesel with 750 Allison transmission, engineered free standing outriggers system, 22 gal 2-station closing unit with N2 backup, 75 ton 2-sheave McKissick traveling block, driller side walkways and complete work floor, current derrick certification, reworked 1985 Price: $500,000

FRANKS 1058 (Ref#348n) Rebuilt- Franks 1058, New Bearings & Seals, New Brake Blocks, New Controls, New Cab & Tires, Rebuilt 8V71 Detroit Diesel Engine, Rebuilt 750 Allison Transmission, New Tulsa Winch, 96’ 4 Leg 200,000# Capacity Derrick, Y Base Magnaflux With Rod & Tubing Board, 4 Axle I Beam Carrier, 4 New Hydraulic Jacks, Appox. 10,000’ 9/16” Sand Line Price: $500,000

COOPER FRANKS 1058 WORKOVER RIG (Ref#1068N) Franks 1058 double drums drawworks, Hydromatic brake, rebuilt hammer, 96’ x 240,000 hydraulically raised mast, 3 sheave McKissick block, 12V71 Detroit diesel engine and rebuilt Allison transmission, Mounted on 4 axle Cooper carrier, Hydraulic leveling jacks, no hand tools, Located in Texas Price: $550,000

FRANKS 1058 (Ref#7544N) single drum drawworks, Lebus grooved for 1” drill line with Foster make-up cathead, mounted on 1983 GMC powered by 6V92 Detroit, Franks Servicer 70’ x 140,000# derrick, with 3-1/2” standpipe, racking board, hydraulic raise and scoped, substructure 6’ high x 10’ x 8’ wide, (1) 9’ x 45’ x 1’6” steel matt mud boat, Ideco D175 17-1/2” rotary table with split master bushings, traveling block, McKissick 5’ elevator bails, Gardner Denver 12” FXZ mud pump powered by 8V71 engine, (10) 4-3/4” spiral drill collars, 4000’ of 3-1/2” drill pipe, (1) 3-1/2” kelly and bushing, (2) 3-1/2 – 4-1/2 slips, (1) pair Web Wilson type GD tongs, (2) extra 6” liners mud pump, bag type blow out preventor, 1 set drill pipe elevators, Dub Allen swivel, doghouse, geolograph recorder, rat hole digger,

International rig up truck with winch, rolling tailboard and gin poles, drill pipe trailer, 35 kw generator light set, currently workiing Price: $440,000

FRANKS 1058 WORKOVER RIG (Ref#10139) Manufactured 1968, double drum (new clutches), new 6000’ sand line, 7/8” tubing line, 69’ x 150,000# mast, mounted on 3 axle carrier w/rebuilt 6V92T Detrit diesel engine, rebuilt 750 Allison automtic transmission, good tires, good condition Off Market

FRANKS 658 SERVICE RIG (Ref#3070N) Manufactured 1974, double drum drawworks, double triple 96’ derrick with a hydromatic. The rig has working line with heavy traveling block and approx. 12,000’ 9/16 sand line. Mounted on Skytop carrier with tandem steering and rear ends W/ tag axel, powered by an 8V-71 with a Allison 4460 transmission, (note transmission was overhauled in early 2000’s) and the engine has a new head on right bank. The rig has two leveling jacks on the rear and two leveling jacks on the front which are located right behind the steering axels. Tooled out with hydraulic rod and tubing tongs, air slips, rod and tubing elevators, hand tools and misc over items. Price: $320,000

FRANKS 658 SERVICE RIG (Ref#3069N) Double drum drawworks with a double double derrick. The rig 7/8 working line with 50 ton travelling block, approx 10,000 9/16 sand line. 1958 International truck powered by 350 cummins with 5x4 transmissions, tandem steering and tandem rear ends and leveling jacks at the rear off the carrier, tooled out with hydraulic rod and tubing tongs, air slips, rod and tubing elevators, hand tools and misc over items. This rig is very fast and extremely user friendly. Price: $220,000

FRANKS WORKOVER RIG (Ref#6038N) Double drum, 50’ hydraulically raised mast, mounted on 2 axle rear carrier powered by Cat 3208 diesel engine, Allison automatic transmission, 4 hydraulic leveling jacks, Foster 74 tongs, hook, block, swivel Price: $240,000

FRANKS 33DD (Ref#9881) double drum pulling unit, 8 x 10 pole w/3-sheave crown, Ramsey hydraulic winch, Tulsa 28 winch, mounted on 1982 International 4300TA truck w/NTC 350 Cummins diesel engine, 2 hydraulic leveling jacks, 5 speed tansmission, 4 speed auxiliary, BJ tongs, Guiberson air slips Off Market

FRANKS DTM 33 (Ref#11273) double drum, 4000’ with ¾ tubing line, Wabco air controls, mounted on 1979 GMC Brigadier and 6 x 4 truck with 6 cylinder engine and PTO, with manual screw jacks, Franks 7” 26# x 5-1/2” 20# double pole mast, 55’ high, cable raised and scoped with single monkey board and tubing block, folding platform, weight indicator, hydraulic power tongs, Guiberson BOP 7-1/16” x 3000# BOP. Handling tools: BJ 2-7/8” elevators, rod hook, 50 ton bales, tubing spider, wrenches Located Southeast Asia Price: $150,000

FRANKS 4000 (Ref#5426) Double Drum, mounted on 4 axle truck, NEW 27-1/2” rotary table, 671 Detroit diesel on mud pump, 453 Detroit diesel on drawworks and table, 75’ x 200,000# mast hydraulically raised (not telescoping), 7 lines on big block, 4 lines on small, hydraulic breakout tongs, mechanical leveling jacks, hook/block, 4-1/2” kelly, 1 extra kelly, Halco centrifugal mud pump 6 x 8 (800 gpm @ 150 psi), 600’ of 4-1/2” x 31’ drill pipe. Pipe trailer Price: $200,000

FRANKS COOPER DOUBLE DRUM WORKOVER RIG (Ref#1557Nb) mounted on 1994 Volvo with Cummins power, 9 speed transmission, Franks drop box 44 Franks tubing drum 32”, Cooper sandline drum, 8 x 10 pole hydraulic winch raised scoped, leveling jacks Price: $110,000

FRANKS KC54 (Ref#11840) Manufactured 1950’s, 4-1/2 x 6 mud pump, 3671 R compressor, mounted on 1978 Chevy truck w/3208 Cat engine, 2 rear hyd leveling jacks, rod rack, bits, collars, tooling, 300’ of 20’ x 2-3/8” Mayhew Reg. drill pipe, currently drilling, good condition Price: $60,000

FRANKS KC-54H (Ref#404N) double drum, mounted on 1975 Chevy truck with 453 Detroit diesel engine, Franks Model 44 PTO, 4 x 5 piston mud pump, 6 – 8” opening on rotary table Price: $80,000

FRANKS KC20 (Ref#8218) Manufactured 1962, 3 x 4 centrifugal pump, 3-1/8 x 14’ kelly, 4-1/4 table, mounted on International B160 truck with 263 3 cyl engine (overhauled) Price: $24,500

KEYSTONE KF-50 (Ref#7124) 585/250 GD air compressor with cyclo blower, 5 x 6 Gardner Denver mud pump, drills 1000’ x 12” hole, 350 Turbo Cummins engine (new), 5-4 sp transmission, AO8 model Meyers water injection, 8-1/2" retractable table, mounted on 1971 International truck, good condition Off market

FRANKS 56 (Ref#9436) Manufactured 1978, Double Drum, air clutches running in oil 15” clutch on drawworks big drum, 4 strand power chain, Ingersoll Rand 365 compressor 365 cfm/125 psi, 5 x 6 Gardner Denver duplex mud pump, 5-1/2” rotary table (removable), mounted on Chevy tandem axle truck with 3208 Cat diesel, PTO, 300’ of drill pipe (20’), 3-5/16” x 34’ Kelly, 20’ rod box, good condition, ready to work Price: $60,000

FRANKS FJ5 (Ref#6899) Double Drum drawworks (3 lines), 100 SDS compressor, mounted on 6 x 6 Crane Carrier powered by Cummins 270 diesel engine, 3 hydraulic leveling jacks, floatation tires, 5 x 6 Gardner Denver duplex mud pump, 4-1/2” kelly,Giant swivel, 2” pulldown chain, sandline, uses 15’ drill pipe, pipe rack, 8-1/2” rotary table, driller’s platform, stand pipe in derrick, 2000’ machine ~~Price~~~~: $95,000~~ – Off Market

FRANKS FJ4 (Ref#15434) 5 x 6 Gorman centrifugal pump, 8-1/2” retractable table, 20’ kelly, swivel, pipe rack, Detroit 671 deck engine, Davey piston air compressor, mounted on 55 Mack truck with diesel engine, rebuilt clutches, sandline, pulldown chains, pipe rack, 150’ of 4-1/2” x 15’ drill pipe, 30’ mast, 3 leveling jacks Price: $45,000

FRANKS FA (Ref#8119) 1954, mounted on 1996 Ford 700 Series, mud pump, tooling, 1500’ of 2-3/4” N rod. 1000 gal water truck (1973) Off Market