SUN MACHINERY CORP.

Call: 516-536-7375 /  516-536-7317 fax

rigs@sunmachinery.com

 

 

Failing -  2500, 1500, 1250, 750, 250, CFD1B, CF15 (TDH), F10, F6, F2

 

FAILING STRATMASTER 100 (Ref#1628N)

1.     Drawworks: G.E. Failing Co, Stratmaster 100 – single drum grooved for 1” wireline, 32” x 10” brake flanges and Parkersburg Hydromatic brake, drum clutch, twin disc air actuated PO-218 with single line pull of 18,030# all mounted on skid, chain driven drawworks modified to enclosed oil bath type chain boxes.

2.     Compound: Gear box – right angle drive series 600 to drive drum, Drop box – rotary drive. All tube torque drive line.

3.     Engines: 1 unit Isuzu 10po1 330ps x 2500 rpm with type “C” mechanical transmission.

4.     Substructure: G.E. Failing Co. design – 8 ft. working space under rotary table – modified, pinned to rig skid.

5.     Hydraulic power: 1 auxillary 25 gpm commercial shearing gear pump, coupled drive from Isuzu engine, 1-45 gpm commercial shearing gear pump driven by 20 HP electric motor mounted on rig.

6.     Rotary table: 20-1/2” opening with no. 3 insert bowl driven by twin disc PO-211 air clutch/chn

7.     Water swivel: Skytop 4 SX 120 ton

8.     Mast: Lee Industries – Beaumont, Texas. 97 ft. mechanical raised, 2 section telescoped type gross load rating 300,000 pipe racking platform for range 2 doubles, capacity for 5000 ft of 4-1/2” drill pipe

9.     Crown block: Structural steel plate construction 6” x 30” OD, sheaves grooved for 1” diameter wireline

10.   Hook block: BJ 100 ton Unimatic 30” x 4 sheaves

11.   Kelly: 3-1/2” x 40 ft. HEX

12.   Kelly drive: 3-1/2” HEX

13.   Mud pump: 1 unit Oilwell A560PT Triplex belt driven by Cat 3412 475hp x 1200 rpm engine with electric starter, engine clutch 18CB-500,

-          Super charged by electric driven 4 x 5 centrifugal pump

-          Electric driven liner wash centrifugal pump

-          2” pressure gauge

-          4” stand pipe valve

-          2” bleed valve

-          2” pressure relief valve, all mounted on discharge line

            All skid mounted in steel building

            L 13.7m x W 2.4m x H 2.6M

       14. Mud system: Skid mounted steel construction tank, 240 BBL capacity 3   

             compartments, complete with mud cleaning and mud mixing equipment,   

             5 x 6 centrifugal pump, hopper, mud jets, desilter, agitator in mixing   

             compartment

15.   Shaker: Double screen Swaco driven 5HP electric motor, mounted on mud tank

16.   Desilter: Drilco 12 x 4” cone mounted in mud mixing room.

17.   BOP’s, Accumulator: 1 unit 9” Nominal Regan annulars 3000 psi, W.P.

18.   Instrumentation: 1 unit TSK W-100 weight indicator

19.   Air compressor: 1 unit Meiji GK-75 with r. tank, 0.78~0.88mpa x 840 ltr. /min

20.   Dog house: Mounted over water tank with tool board & drillers desk. L 4.6m x W 2.1m x H 2.1m

21.   Combination building: Steel construction skid mounted, consists of: tool house, work shop, change house, power control/distribution house, fuel tank 7000 ltr. capacity mounted on house, etc.  

22.   Drill pipe

23.   Drill collars: 18 joints 6-1/2” x 2-7/8” 5” pin x H90 box, 2 joints 9” x 3”  7” pin x H90 box

24.   Misc. handling tools: DC. 9”, 6-1/”, 4-3/4”~9”, various DP/DC slips & elevators, BJ C type rotary tongs, CSG elevators, various subs XO, lifting, bit, etc., junk box, steel tank.

25.   HWDP: 11 joints heavy weight drill pipe

26.   Vibrator hose: 3000 psig 2.5m

27.   Rotary hose: 5000 psig x 3-1/2”

28.   Rig lighting: Northern rig lights, fluorescent and Halogen lamps, sealed and explosion proof throughout.

29.   Pipe racks: 2 sets 30 ft. long tumble rack system

30.   Cat walk (pipe tub): 2 units – square tubing construction skidded 40 ft. long with pipe bin, capacity 3,000 ft. x 4-1/2” D.P.

31.   Drilling line: 1” x 400m with steel construction rack.

 Converted and refurbished from trailer to skid mounted rig. Immediately available for sale in Southeast Asia. Hasn’t drilled since 1998. Refurbished in 2000.

PRICE REDUCED  $350,000

 

FAILING 3000  (Ref#9879N)  4000’ depth, double drum, 72’ x 100,000# hydraulically raised mast, racking board, crown block, 6 kelly line sheqaves, single sand line sheave, 14” x 7-1/2” Gardner Denver duplex mud pump, Wabco Model 2 AVC  air compressor, 18” rotary table, (2) diesel engines, weight indicator, Regan BOP, 5’ substructure, handling toos, drill pipe trailer, camp trailer, welding trailer, kelly hose, mud mixing, hopper, 1600’ of 4-1/2” drill pipe, (4) 6” pipe collars  Price:  $500,000

 

FAILING 3000  (Ref#37N)  Manufactured 1980, double drum, no pulldown, mounted on 3 axle trailer, (2) Detroit 471 diesel engine on deck, 65’ x 140,000# hydraulically raised mast (pipe type), 18” fold up table, 7-1/2 x 10 duplex mud pump, rig is dismantled and requires refurbishing, assembly, cleaning and painting, stored inside  Price:  $150,000

 

FAILING JED-A  (Ref#11224N)   Manufactured 1972, double drum drawworks, sandreel, trailer mounted, (2) deck engines Detroit 371 and Detroit 471, LeRoi 50SDS air compressor, Gorman Rupp centrifugal mud pump, jet eductor/self-priming, 18” retractable rotary table, heavy duty derrick 49’10” long x 60,000#, air controls, jet eductor system, Kipor KDE 6700TA diesel generator, mounted on tandem axle low boy drop frame trailer Model 147F240,  4 hydraulic leveling jacks, some tools, no pipe, excellent condition  Price:  $225,000

 

FAILING JED-A  (Ref#7639N)  mounted on 1980 Ford LT9000 truck with 290 Cummins engine, 18” Failling rotary table, 49.5’ mast (handles double random casing), 3 drum stacked drawworks (2) 16” air clutches rated at 15,000# single line pull), 4 hydraulic leveling jacks, McKissick 3 sheave traveling block on kelly, Failing 2 sheave traveling block on hoisting drum, Packer Jr. weight indicator, King 25WV swivel, Foster cathead with spinning chain, hydraulic breakout cylinder, Webb Wilson breakout tongs, complete set of bit subs, 7-1/4 x 10” Gardner Denver skidded mud pump with 671 Detroit diesel power unit, 1,000’ drill string (960’ of 3.5” x 20’ drill pipe, (2) 20’ drill collars and 26’ kelly), reverse swivel and 6” flanged reverse drill pipe also available.  Price:  $350,000

 

FAILING JED-A  (Ref#13384N)  triple drum, rebuilt, 1000’ of 3/8” sandline, (2) 4 part blocks, wireline drum, mounted on single axle truck, (2) front trailer jacks, (2) rear screw jacks, Detroit 471 diesel engine with 1600 hours, 4 x 5 Gorman Rupp centrifugal mud pump, (1) 175 gallon fuel tanks, 7” x 14’ kelly, swivel rebuilt  Price:  $190,000  Price reduced:  $165,000

 

FAILING JED-A (Ref#2153N) Detroit 471 deck engine, mounted on 1989 Peterbilt 357 with 425 hp Cat engine, no mud, no air, currently drilling, no pipe or tools  Price:  $170,000

 

FAILING JED-A  (Ref#11225N)  471 Detroit deck engine, 5 x 6 Mission Magnum centrifugal mud pump, 90,000# mast, set up for reverse circulation, mounted on 1989 Peterbilt truck with 3406 Cat engine, 4 hydraulic leveling jacks, kelly, good operating condition  Price:  $225,000

 

FAILING 4500 HOLEMASTER  (Ref#15195)  depth capacity 2500’ with 3-1/2” drill pipe, 5000’ with 2-3/8” drill pipe, mounted on dual wheel tandem axle trailer, 180 hp diesel engine, 65’ x 133,000# hydraulically telescoping mast, 18” rotary table, bottleneck drill pipe, blow out preventors, located Middle East  Price:  $250,000

 

FAILING 2500  (Ref#438N)  Manufactured 1981, double drum, reconditioned 80%, tandem axle trailer mounted, twin GM 4 cylinder diesel engine, 18” rotary table, kelly swivel, travelling block, new tires, mechanical tongs, base of mst damaged during repair (requires inspection)  Price:  $200,000

 

FAILING 2500  (Ref#5152N)  2500’ depth capacity, manufactured 1989, low hours, mounted on tandem axle trailer, substructure, double drum drawworks, 18” rotary table, cathead, 48’ x 90,000# maximum hook load, 5 x 8” duplex mud pump, (2) diesel engine, weight 57,000#, located Middle East, will be delivered to East Coast US Port  Price:  $180,000

 

FAILING 2500  (Ref#14862)  single drum, air clutch, cathead, small drum to raise mast, mounted on 2 axle trailer with leveling jacks, (2) GMC 471 diesel engines, (2) transmission, work platform, rig can use 1 or 2 engines, Gardner Denver 5 x 7” duplex mud pump, 17-1/2” rotary table, kelly, kelly bushings, hook/block, swivel, 59’ x 70,000# mast, currently drilling, located in Mexico  Price, delivered to Texas/Mexico border:  $165,000

 

FAILING 2500E  (Ref#12476)  Manufactured 1979, mounted on 6 x 6 truck, capable of drilling boreholes to a depth up to 400 meters, 18” rotary table opening, 14.5 meter mast height x 60,000 lbs, safe working load 50,000 lbs., (2) Detroit diesel engines, no mud pump, excellent working condition, located Middle East  Price:  $125,000 delivered to Middle East Port

 

FAILING 2500 E (Ref#1189Nb)  Manufactured 1974, last used 2000, requires refurbishing.  Mounted on articulated trailer, 5-1/2” x 8 Gardner Denver duplex mud pump, 59’ x 70,000# telescoping mast, 17-1/2” rotary table, No pulldown, Depth capacity 2400’    Price: 120,000£   Location: UK. Not used in several years.

 

FAILING 2000 CE (Ref#1189Na)  Manufactured 1970, last used 1990, requires refurbishing.  Mounted on articulated trailer, Powered by GMC71 diesel engine, 17-1/2” rotary table, Depth capacity 1800’, No pulldown  Price: 70,000£   Location: UK. Not used in several years.

 

FAILING 2000CF  (Ref#3748N)  double drum, mounted on tandem axle trailer, 4 hydraulic leveling jacks, hydraulic pulldown chain, 30XV King swivel, blocks, 18” rotary, 5-1/2 x 8” Gardner Denver duplex mud pump powered by Detroit 6V71 engine, air compressor, 6V71 Detroit deck engine, 30’ square kelly, hydraulically raised mast 50’, has run 40’ casing, gone over in 2008, drilled 1 well in 2008, being sold due to lack of work.

The following specifications are estimated:  deck engine model, length and capacity of mast, length and diameter of kelly   Price:  $275,000    

 

FAILING CF2000  (Ref#4504N)  Manufactured 1979, mounted on tandem axle trailer, 18” flip up rotary table, double drum drawworks with stacked sandline, both lines parted 6 imes, Wichita air clutches, piston air comressor, 471 Detroit engine, 58” single mast, 35’ hex kelly bar, big bore swivel with air injection, (2) breakout and make up tongs with hydraulic cyl., weight indicator, table slips, substructure, 3 hydraulic stabilizer jacks, fold down walk way around rig with stairs.  Price:  $325,000

 

FAILING 2000  (Ref#12819N)  FXD 5 x 10 duplex mud pump mounted on rig, 56’ x 75,000# hydraulically raised mast, 4” x 34’ fluted kelly, rigged for 3 part line, 18” rotary table, no pulldowns, mounted on 1982 Peterbilt 2-axle rear truck powered by 350 Cummins diesel, 4 hydraulic levelling jacks. 

Price:  $250,000

Available at extra cost:

FXD 5 x 10 duplex mud pump trailer mounted, light plant and compressor, 1770’ of 4-1/2” drill pipe, 100’ (4) 5-3/4” drill collars 

 

FAILING 1500  (Ref#453N)  5 x 8 Gardner Denver mud pump, no air, mounted on 1990 Ford 8000 truck with 370 Ford diesel engine, 44’ derrick, hydraulic pulldown, 8-1/2” retractable rtoary table, air clutch, rod rack, mud pan, completely rebuilt 2000, 4 jacks, 600’ of 3-1/2” x 20’ slick joint with 2-7/8 IF  Price:  $170,000

 

FAILING 1500  (Ref#471N)  mounted on 1989 International truck with diesel engine, PTO, 5 x 6 mud pump, stationary table, breakout wrench, 4 hydraulic leveling jacks, no pipe or tools  Price on Request

 

FAILING 1500  (Ref#260N)  Manufactured 1987, mounted on 1987 International 6 wheel truck, DT466 engine, air brakes, 5 x 6 mud pump, PTO, 3 hydraulic leveling jacks, no tools/pipe    POR

 

FAILING 1500  (Ref#8553Na)   37’ derrick, 5 x 6 Gardner Denver mud pump, developmental air, 26’6” kelly, breakout table, cathead, mechanical clutches, no pulldown, mounted on 1990 Chevy truck with gas engine (rebuilt), no leveling jacks, good condition, currently drilling  Price:  $60,000

300’ of 2-3/8” x 15’ drill pipe available for extra cost

 

FAILING 1500 HOLEMASTER  (Ref#13620N)  mounted on 1979 6 x 6 truck with 345 gas engine, PTO, breakout table, mechanical clutches, pulldown, 4 x 5 duplex mud pump, racking board, 2 rear hydraulic leveling jacks, 200’ of Mayhew Jr. pipe  Price:  $50,000

 

FAILING 1500 HOLEMASTER  (Ref#7407N)  Continental gas deck engine, mounted on 1988 International with V8 gas engine, 3 hydraulic levelng jacks, 4 x 5 GD mud pump, retractable table, 3” x 20’ kelly, mechanical clutches, 4” hydraulic pulldown, shaker screen, fully toooled, 300-400’ drill pipe  Price:  $40,000

 

FAILING 1500 HOLEMASTER  (Ref#10819N)  5 x 6 mud pump, mounted on 1967 Chevy 2-1/2 ton truck (rebuilt 2 years ago), 350 Chevy V8 engine, PTO, turntable, 4” kelly bar, 400’ of 10’ drill stem,  Price:  $55,000

 

FAILING 1500  (Ref#3589N)  Manufactured 1980’s, (2) Detroit 371 diesel deck engines, 5 x 6 Failing mud pump, 40’ hydraulically raised mast, 2-7/8” x 28’6” fluted kelly, twin cylinder pulldown, 7-1/2” rotary table, mounted on 2000 International 4900 truck with rebuilt DT466 engine (Less than 50 miles),  mechanical clutches, 4 hyd leveling jacks, breakout wrench, no tools or pipe, low hours, reconditioned and repainted,  Price:  $85,000

 

FAILING 1500  (Ref#14375)  double drum drawworks (rebuilt), 40’ mast, mounted on 1981 International truck with DT466 diesel engine, 4 hydraulic leveling jacks, Gardner Denver 150 cfm/200 psi air compressor, PTO drive with large tansfer case 654C, 15XV King swivel 2”, 2 large blocks, 5 x 6 Gardner Denver duplex mud pump, 6-1/2” fixed removable table, has drilled to 1400’, drills when there is work  Price:  $115,000

 

FAILING 1500  (Ref#1101N)  mounted on 1985 Ford F700 truck with 370 gas engine, 5 x 6 mud pump, 8” retractable table, 2-7/8” x 27’ kelly, mechanical clutches, pulldown, 2 rear hyd leveling jacks, 43’ mast, 3 winches, no tools, good condition  Price:  $48,500   Pipe available at extra cost

 

(5) FAILING 1500 GEOTECHNICAL RIGS  (Ref#8818)

 (1) Failing 1500, Manufactured 1985, Mounted on Ford F700 with Gas engine, 5 x 6 Gardner Denver mud pump, 47’ mast, 3 drums, Hydraulic jacks, Mast lift, Chain drive table, Cathead, Hydraulic pulldown, No air,

(2) Failing 1500, Manufactured (1) 1984 & (1) 1985, Mounted on Ford F700 with Gas engine, 5 x 6 Gardner Denver mud pump, 45’ mast, Hydraulic jacks, Mast lift, Chain drive table, Cathead, Hydraulic pulldown, No air

(1)  Failing 1500, Manufactured 1981, Mounted on International with Gas engine, 5 x 6 Gardner Denver mud pump, 35’ mast, Hydraulic jacks, Mast lift, Chain drive table, Cathead, Hydraulic pulldown, No air

Price:  $35,000 each rig

Call for Package Price

 

FAILING 1500DMX  (Ref#12189N)  Manufactured 1986, 985 hours, sotred inside, (current owner bought new) double drum, 46’ x 60,000# hydraulically raised mast,  5-1/2 x 8” duplex mud pump, blocks, breakout wrench, 3-1/2” x 23’ kelly (currently running 20’ drill pipe) mounted on International tandem axle rear truck, DT466 diesel engine, PTO, 4 hydraulic leveling jacks, excellent condition, stored inside  Price:  $295,000

 

FAILING 1500  (Ref#451N)  Manufactured 1973, 5 x 6-1/4 mud pump, 2-7/8” x 24’ kelly, 5-1/4” stationary table, breakout wrench, pulldown, mechanical clutches, mounted on 1973 GMC 7000 Series truck with Detroit engine, PTO, 2 manual rear jacks, well maintained, one owner rig, 400’ of 2-3/8” x 20’ drill pipe, ready to go  Price:  $70,000

 

FAILING 1500  (Ref#250N)  Manufactured 1993, 5 x 6 mud pump, mounted on 1993 GMC single axle Topkick with Cat 6 cyl diesel engine, PTO, 42’ derrick with 10’ section that can be removed, mechanical clutch, mechanical brake, hydraulic pulldown, hydraulic derrick, no jacks, 8-1/2” retractable table, 2-7/8” kelly, no cathead  Price:  $62,500

500’ of 2-3/8” FEDP pipe available at extra cost

 

FAILING 1500 HOLEMASTER  (Ref#9147Na)  Manufactured 1972, mounted on 1976 Ford F600 4 x 4 truck, 391 gas engine, PTO, winch, 4 x 3 x 13 Mission centrifugal pump, 42’ derrick, hydraulic pulldown, manual clutches, all new hoss, roller bits, 15’ stabilizer, 200’ of 2-3/8” x 20’ pipe, 180’ fused drill rod, subs, mud pan, hoisting plug, swivel, etc, fully tooled,  Price:  $55000

Available at additional cost:

2000 INTERNATIONAL 1500 WATER TRUCK  (Ref#9147Nb)  1500 gallon flatbed water tank, V8 air compressor, pipe trough, toolbox, T4443 Turbo engine, Viper hydraulic grouter

 

FAILING 1500  (Ref#14626)  Manufactured 1972, mounted on 1986 Ford F6000 truck, 30,000 miles, Cat 3406 engine, 100’ of N Rod, 10’ joint pipe, slips, 4-1/2 x 5 Gardner Denver mud pump, recently painted  Price:  $47,500

 

FAILING 1500  (Ref#15450)  Manufactured 1971, 42’ mast, FM 5 x 6-1/2” double manifold Failing pump (3 years old), heavy duty breakout table, mounted on original 1971 GMC truck with Detroit 6V53 engine, currently drilling,

500’ Failing 2-3/8” x 20’ FEDP drill pipe (good condition), 500’ Failing 2-7/8” x 20’ FEDP (good condition) (2) drill collars (1000# locking Hacker), subs, bits, brand new King XV15 swivel.  One owner rig.

1989 Ford F800 water truck with 1300 gal square tank, mounted on steel body, low mileage

Price for above:  $80,000

 

FAILING 1500 (Ref#2430N) Manufactured early 1970’s, completely refurbished,  PTO, mounted on 1979 Ford F700 (not 4x4) with gas engine, 6 x 8 Gardner Denver mud pump, no air, 2 15/16” x 27’ fluted Kelly, extended mast, hydraulic pulldown, retractable rotary table, mechanical clutches, no leveling jacks, toolbox, no tools available  Price:  $48,500

Set up for N rods – avail, neg $$

 

FAILING 1500  (Ref#3019)  27’ mast, friction clutch, 2-3/8” kelly, hydraulic pulldown, no pipe or tools

(1) Mounted on 1998 Ford F800 4x4 truck  Price:  $49,500

(1) not mounted  Price:  $29,500

 

FAILING 1500 (Ref#4674N)  1500 drawworks, PTO, mounted on International with DT466 engine, piston mud pump, retractable table, mechanical clutches, hydraulic pulldown, 2 3/8” Kelly, 1 front & 2 rear hydraulic leveling jacks  Price:  $42,000

 

FAILING 1500  (Ref#8192N)  5 x 10 Gardner Denver mud pump, Failing drawworks, retractable table, 3-7/8” kelly, air clutches, hydraulic pulldown, mounted on International Chassis with Detroit engine, 4 hyd leveling jacks, no tools or pipe,  not used in 10 years  Price:  $40,000

 

FAILING 1500 HOLEMASTER  (Ref#13234)  Manufactured 1950, mounted on 1950 GMC FC 453 truck with 270 C.I.D. Military engine, 38’ mast, 2-7/8” x 28’ kelly, 5 x 6 Gardner Denver mud pump, 600’ of Failing exploration drill pipe, drill collars, tools, excellent condition    Price on request

 

FAILING 1500  (Ref#13388)  Mounted on 1987 Ford 800 truck w/gas engine, PTO, 4 x 5 GD mud pump (rebuilt), hydraulic pulldown, 2-3/8” kelly, retractable table, 150’ drill pipe  Price:  $45,000

 

FAILING 1500  (Ref#1743N)  Manufactured 1970’s, 5 x 6 Gardner Denver mud pump, diesel deck engine, 5-1/4” retractable table, 2-3/8” x 29’ kelly, 42’ mast, hydraulic pulldown, mechanical clutches, mounted on Ford F700 truck (not 4x4) with gas engine, 3 hydraulic leveling jacks, 300’ of 2-3/8” x 15’ drill pipe  Price:  $45,000

 

FAILING 1500  (Ref#15617)  1970’s, mounted on 1984 Chevy 70 Series single axle truck with new Cat 3208 engine, PTO, 5 x 6 Gardner Denver mud pump rebuilt, big air compressor, 44’ derrick, Failing swivel, 2 winches, 2-7/8” kelly, retractable table, cathead, hyd breakout cylinder, mechanical clutches, hydraulic pulldown, 2 rear hyd leveling jacks, bits, subs, drill collar, misc tools, pipe racks, 700’ of 2-7/8” x 20’ Failing heavy duty drill pipe, excellent condition, currently drilling   Price:  $90,000

Also available 600’ of 2-3/8” x 20’ Failing heavy duty drill pipe

 

FAILING 1500  (Ref#13984)  Manufactured 1975, mounted on 1965 truck, 250 Cummins engine, LeRoi 250 psi air compressor, 5 x 6 Failing mud pump, 300’ of 2-3/8” drill pipe, 200’ 2-3/8 Mayhew Reg pipe  Price:  $65,000

 

FAILING 1500  (Ref#384Na)  Manufactured 1973, 5 x 6-1/2 mud pump, LeRoi 2-stage 4AWC comparessor 100/125, mounted on 1994 International single axle truck with DT466 diesel engine, PTO, 8-1/2” retractable table, mechanical clutches, 30” stroke, hydraulic pulldown, no rod racks  Price:  $55,000

Also availale at extra cost:  tandem axle pipe trailer, 1100 gal water tank, 460’ pipe

 

FAILING 1500  (Ref#1018N)  Manufactured 1970, mounted on Mack truck 3 axle, Ford diesel deck engine, diesel engine in truck, 4 x 5 Failing mud pump, no air, 27’ extended mast, 15’ kelly, fair condition, pipe available at extra cost  Price:  $30,000

 

FAILING 1500 (Ref#2132N) Manufactured 1970, PTO, mounted on 1987 Ford 800 4x4 with 6.6 liter diesel engine, 27’ mast, hydraulic chuck, 10’ stroke, 5 x 6 Ό  mud pump, 2 7/8” Kelly  Price:  $50,000

210’ NWJ rod & 400’ of 2 3/8” IF pipe available at additional cost

 

FAILING CF-1500  (Ref#12780)  5 x 6 Gardner Denver mud pump, developmental air compressor (removed), mounted on International truck with gas or propane, PTO  Price:  $32,500

 

FAILING 1500  (Ref#9366)  5 x 6 mud pump, 30’ mast with 10’ extension, mounted on 1974 Ford F600 (gas or propane), drill pipe, trucks needs replacing    Price:  $20,000

 

FAILING 1500  (Ref#5944) 1973, 5 x 6 mud pump, on 1966 10-wheeler 6x6 Kaiser military truck  (fair condition) with 6 cyl diesel, 8” rotary table, inserts, breakout table, (2) hydraulic jacks, 35’ mast, 2-3/8” kelly, rig good condition  Price:  $45,000

New 300’ of 2-7/8” x 20’ FEDP thread, used 300’ end rod 4-thread, available at extra cost

 

FAILING 1500  (Ref#14790)  5 x 6 Gardner Denver mud pump, mechanical clutches, 200’ of 2-3/8” x 20’ drill pipe, bits, subs, handling tools (sitting a few years)  Price:  $30,000

 

FAILING 1500  (Ref#9437)  Double drum, older rig 1956, 42’ mast, mounted on 1979 Ford 9000 truck with 671 Detroit diesel engine, 6 cylinder gasoline engine on deck  Price:  $45,000

4-1/2” x 6” mud pump available for an additional cost

 

FAILING 1500  (Ref#6458N)  Manufactured 1966, fully rebuilt, mounted on 1987 Ford F700 truck with 470 gas motor, 259” wheelbase, FM45 pump (rebuilt), transfer case rebuilt, 1 brand new hoisting drum, new quill, new bearings ring and pinion, 5 x 6 mud pump, no air, 42’ mast, 2-3/8” 27’ kelly bar (almost new), mechanical clutches, pulldown, stationary table, no breakout wrench, no pipe or tools  Price:  $55,000

 

FAILING 1500 HOLEMASTER (Ref#4882N) Manufactured 1964, PTO, mounted on 1961 International with gas engine, 4 x 5 Gardner Denver mud pump, retractable table, hydraulic pulldown, mechanical clutches, no leveling jacks, 90’ of 2 3/8” x 10’ drill pipe, 4 brand new bits  Price:  $40,000

 

FAILING 1500 (Ref#9014Nb) Mounted on 1964 Ford truck, stationary table, Leroi air compressor, no mud pump  Price:  $45,000

 

FAILING HD36  (Ref#1305N)  4-1/2 x 5 mud pump, big air compressor, 42’ mast, Failing swivel, 2-3/8” kelly, cathead, mechanical clutches, mounted on 1979 Chevy single axle truck with Detroit diesel engine, 3 rear hydraulic leveling jacks, drill collars, some tools, 600’ of 2-3/.8” x 20’ heavy duty Failing drill pipe, good condition, currently drilling  Price: $60,000

 

FAILING 430DD PULLING UNIT  (Ref#8391N)  Double drum, 42’ telescoping mast, Johnson 30 ton blocks,  air slips, Pennant weight indicator, 200’ of 3/8” sandline (new) , 5/8” mainline (new), new clutch pads, mounted on 1985 Peterbilt truck with 400 Cummins engine, 13 speed transmission, SK power tongs, good condition  Price:  $105,000

 

FAILING 1250 (Ref#10189Na) PTO, mounted on 1995 Ford F900 with 250hp diesel engine, 5x6 mud pump, 560/75 GD air compressor, sandline, 300’ pipe, some tools  Price:  $105,000

 

FAILING 1250  (Ref#6453N)  air compressor, 23’ kelly, pulldown, mechanical clutches, 5-1/2” retractable table, mounted on 1981 Ford F700 4-wheel drive truck with Cat 3406 engine, breakout wrench, 2 rear hyd leveling jacks, , excellent condition, 200’ of 2-3/8 x 15’ drill pipe, breakout wrench, currently drilling  Price:  $150,000 

 

FAILING 1250 (Ref#1734N) Manufactured 1978, PTO, mounted on Ford with diesel engine, 3 x 4 mud pump, 500/200 on board air compressor, 6” retractable table, chain pulldown, mechanical clutches, breakout wrench, 1 front & 2 rear hydraulic leveling jacks, 2 7/8” x 20’ drill pipe

Price on request

 

FAILING 1250 (Ref#1735N) Manufactured 1982, PTO, mounted on International with diesel engine, 3 x 4 mud pump, 250/200 on board air compressor, retractable table, chain pulldown, air clutches, breakout wrench, 1 front & 2 rear hydraulic leveling jacks, 2 7/8” x 20’ drill pipe

Price on request

 

FAILING 1250  (Ref#2250N)  mounted on 1978 Ford 9000 truck with 3208 Cat engine, PTO, 5 x 6 Gardner Denver mud pump, developmental air compressor, 5-1/4” stationary table, mechanical clutches, pulldown, 18’ kelly, 100’ of 2-3/8” pipe, 3 hydraulic leveling jacks, no tools, good condition  Price:  $60,000

 

FAILING 1250 (Ref#15254Na) PTO, mounted on International tandem axle with DT 466 engine, 5 x 6 mud pump, air compressor, 5 Ό” retractable table, chain pulldown, mechanical clutches, 360’ drill pipe  Price:  $140,000

 

FAILING 1250 (Ref#14980)  Manufactured 2001, 5 x 6 Failing duplex mud pump, 2-7/8” fluted kelly, aux winch, cathead, front winch 20,000#, 4 hyd leveling jacks, handling tools, mounted on International single axle truckwith all wheel drive and Detroit DT466 diesel engine, 32’ mast, 120’ of 2-3/8” x 10’ Mayhew Jr pipe, excellent condition, currently drilling, less than 100 hours, less than 200 miles,  like new  Price:  $230,000

 

FAILING 1250  (Ref#1128N)  Manufactured 1995, mounted on 1994 Western Star truck, Cat 3406B engine, PTO, 850/250 GHH air compressor, 15 gpm water injection, no mud, 3” kelly, new paint, ready to work  Price:  $130,000

 

FAILING 1250  (Ref#2162N)  Manufactured 1986, 5 x 6 mud pump, LeRoi air compressor, mounted on 1986 International single axle truck with DT466 engine, 24’ x 2-7/8” fluted kelly, 7-1/2” rotary table, mechanical clutches, no pulldown, no breakout wrench, 3 hyd leveling jacks, no pipe or tools  Price:  $60,000

 

FAILING 1250  (Ref#328Na)  Manufactured 1980, 5 x 8 Gardner Denver mud pump, air compressor removed, mounted on 1979 Ford 9000 truck with 300 Cummins, PTO, 7-1/2” retractable rotary table, 300’ of 2-7/8” pipe with 2-3/8 IF conn, no tools, chain pulldown  Price:  $75,000

1981 FORD 9000 WATER TRUCK  (Ref#328Nb)  4000 gal tank, tandem axle, 3208 Cat engine, auto transmission

Package Price:  $85,000

 

FAILING 1250  (Ref#245N)  Manufactured 1980’s, mounted on 1991 GMC tandem axle truck with diesel engine, PTO, Wheatley 6zx6 mud pump, 500/200 air compressor, 3-7/8” x 23’ fluted kelly, pulldown, air clutches, Bean water injection, hammer oiler, 5-1/2” retractable table, breakout tongs, 4 hdyraulic levleing jacks, 2-7/8” x 20’ drill pipe, excellent condition, curently drilling  Price:  $150,000

 

FAILING 1250  (Ref#2994N)  LeRoi 650/150 air compressor, no mud pump, mechanical clutches, hydraulic pulldown, breakout tongs, 3-3/4” x 23’ fluted kelly, 12 gpm water injection, 8-1/2” stationary table, swivel, 4 hydraulic leveling jacks, mounted on 1993 Kenwroth tandem axle truck w/L10 Cummins engine, 10 speed transmission, 280’ of 3-1/2” FJ x 20’ drill pipe, excellent condition, drills everyday  Price:  $110,000

 

FAILING 1250  (ref#8328N)  Manufactured 1988, 256 LeRoi air compressor, mounted on Ford F8000, 671 Detroit diesel engine, PTO, 2 cyl Bean water injection, standard mast, runs 20’ pipe, 300’ of 3-1/2” pipe, drill collar, bits, subs, running condition  Price:  $95,000

 

FAILING 1250  (Ref#2170N)  Manufactured 1987, 185 Sullair compressor, (2) Gardner Denver 5 x  mud pumps, mounted on 2004 International 7400 all-wheel drive tandem axle truck with diesel engine (3200 miles), PTO, new King swivel, Boyles Brothers 40,000# mast, air clutches, chain pulldown, 7-1/2” retractable table, breakout wrench, 4 hydraulic leveling jacks, good condition  Price:  $305,000

500’ of 2-3/8” Mayhew reg pipe available at additional cost

 

FAILING 1250  (Ref#799N)  Retrofitted 1981, 5 x 6-1/4 Failing mud pump, mounted on 1985 Mack truck with 300 hp diesel engine, 5-1/4” rotary table with 3 speed transmission, 100S1 LeRoi air compressor, Fuller 3TA92 aux transfer case, PTO, breakout tongs, rear hydraulic jacks, air clutches, cathead, 3rd drum capability, last drilled November 2008  Price:  $75,000

 

FAILING 1250  (Ref#10385N)  5 x 6 mud pump, 50S1 LeRoi air compressor, pulldown, mechanical clutches, mounted on International tandem axle truck with gas engine, 40,000# mast, 15,000# drawworks, 3 drum bailer, operator’s platform, 3 hydraulic leveling jacks, 240’ of 3-1/2” x 15’ FJ (2-3/8 IF) drill pipe, LF breakout wrench, good condition, currently drilling  Price:  $85,000

 

FAILING 1250  (Ref#1088N)  mounted on 1995 International 4300 truck with DT466 engine, PTO, 5 x 6 Failing mud pump, Dresser 990A 125 cfm air compressor, retractable table, 3rd line, breakout wrench, mechanical clutches, pulldown, 22’ kelly, 4 hyd leveling jacks, good condition, 300’ of 3-1/2” x 120’ drill pipe, 140’ of 20’ Failing exploration pipe   Price:  $90,000

 

FAILING 1250  (Ref#1082N)  mounted on 1981 International truck with DT466 engine, PTO, 5-1/4” retractable table, 5 x 6 Gardner Denver mud pump, 2-7/8” x 24’ kelly, pulldown available (was removed), no leveling jacks, good condition  Price:  $65,000  Pipe available at extra cost

 

FAILING 1250 (Ref#1132N)  Double drum drawworks, mounted on 1980 International 3 axle truck with 3 hydraulic leveling jacks, 32’ mast, FM-45 5 x 6 Ό” duplex mud pump, auxiliary air compressor for development,  5 Ό” retractable table, 20’ rod rack, hydraulic chain pulldown, drill pipe at extra cost   Price: $85,000

 

FAILING 1250  (Ref#3275Na)  5 x 6-1/4” mud pump, 990A Dresser air compressor, 23’ kelly, 5-1/4” retractable table, pulldown, mechanical clutches, mounted on 1995 International 4900 truck with diesel engine, 4 hydraulic leveling jacks, 300’ of 3-1/2” x 15’ drill pipe, good condition  Price:  $90,000

Also available:

1987 Freightliner Water Truck  (Ref#3275Nb) tandem axle, Cat engine, 2700 gallon rectangular tank  Price:  $30,000

 

FAILING 1250  (Ref#1828N)  Manufactured 1979, 100 S1 Dresser air compressor, 3-3/8” x 23’ kelly, 5 x 6-1/2 mud pump, 5-1/4” retractable table, pulldown, mechanical clutches, breakout wrench, mounted on International Paystar 5000 with 290 Cummins engine, 400’ of 2-3/8” IF drill pipe, 3 hyd leveling jacks,

Kenworth T800 water truck, 2000 gallon Flatwater fleet water tank, 200 gal aux fuel tank, torch cabinet

Package Price:  $150,000

 

FAILING 1250  (Ref#778N)  Manufactured 1979, completely rebuilt, allnew hydraulics, etc., PTO, mounted on 1997 International 9500 with DT466 engine, 5 x 6 mud pump, LeRoi 100S2 air compressor, 7-1/2” retractable table, new pulldown chains, 4 hyd levelling jacks, Myers water injection, 3-1/2” x 24’ kelly, 34’ mast, mechanical clutches, 140’ of 2-7/8” x 20’ drill pipe, ready to go, excellent condition  Price:  $235,000

 

FAILING CF1250  (Ref#1133N)  developmental air, 5 x 6 duplex mud pump, mounted on single axle International truck with gasoline engine, good condition  Price:  $65,000

 

FAILING 1250 HD HOLEMASTER  (Ref#546N)  Manufactured 1978, mounted on 6x6 Military truck 2-1/2 ton, 130,000 miles, high and low range, 5x 8 mud pump, no air, 250 Cummins engine, no pipe or tools  Price:  $50,000

 

FAILING 1250  (Ref#8435)  Manufactured 1978, 100 SDS air compressor, 50 S1 air compressor, Cat 3208 engine, mounted on 981 Ford truck, 3 x 2 mud pump, no tools  Price:  $70,000

 

FAILING 1250  (Ref#14294)  5 x 6-1/4 mud pump, LeRoi 100 S1 air compressor, cathead, 3rd drum capability, mounted on Mack tandem axle truck, bits, pipe  Price:  $90,000

 

FAILING 1250  (Ref#8303Nb)  Manufactured 1970’s, mounted on Paystar 5000 tandem axle truck, 3208 Cat engine, 3rd drum, 500 gallon water tank, 5 x 6-1/2” mud pump, 5-3/4” retractable table, 3 leveling jacks, 250’ of 2-3/8 Mayhew Jr pipe  Price:  $85,000

 

FAILING 1250  (Ref#11318)  Manufactured 1980, 450/250 LeRoi air compressor, mounted on 1980 International tandem axle truck with 350 Cummins engine, currently drilling, good condition, well maintained, 500’ of 3-1/2” flush drill pipe, 1990 Volvo water truck with 3000 gal tank and 300 Cummins engine, 20’ pipe trailer  Package Price:  $90,000

 

FAILING 1250  (Ref#15204N)  Manufactured 1978, mounted on 1978 GMC tandem axle truck with Detroit diesel engine, PTO, 4 x 5 mud pump, large air compressor, 21’ kelly, hydraulic pulldown, stabilizer, extra sandline, 300’ drill pipe, good running condition,  Price:  $65,000

Available at extra cost:

1990’s GMC WATER TRUCK  3200 gallon square tank, pipe racks, 3 toolboxes, 48,000 miles on truck 

200’ pipe, parts including water connectors, breakout wrenches, etc.

 

FAILING 1250 HOLEMASTER  (Ref#281Na)  Manufactured 1978, rebuilt 5 x 6 Gardner Denver mud pump, 5-1/4” retractable table, mounted on Ford F7000 truck with Cat 3208 engine, 20 gpm Bean water injection, mechanical clutches, extra hoist, drum line, 23’ kelly, good condition  Price:  $60,000  OFF MARKET

 

FAILING 1250  (Ref#3498N)  5 x 6 mud pump, developmental air, 5-1/4” retractable table, 3-3/8” kelly, pulldown, mechanical clutches, mounted on 1987 International Paystar with 400 Cummins, 3 hyd leveling jacks, heavy breakout tongs, 300’ of 2-3/8 IF x 20’ drill pipe, good condition, stored inside, drills daily  Price:  $105,000

 

FAILING 1250 (Ref#11009N) Manufactured 1973, PTO, mounted  on 1987 International 4900 with DT466 engine, 5 x 6 Ό” Failing mud pump, 100 CFM developmental air compressor, 24’ Kelly, all tools for 4” & 5” wells, 225’ of 15’ drill rods  Price:  $100,000

 

FAILING 1250  (Ref#3712N)  mounted on 1973 Ford tandem axle truck with gas engine, 5 x 6 mud pump, developmental air, new 5” x 15’ kelly, new swivel, mechanical clutches, pulldown, 300’ pipe, no leveling jakcs  Price:  $45,000

 

FAILING 1250  (Ref#881N)  Manufactured 1972, mounted on 1972 International F210D with 250 hp Cummins engine, PTO, LeRoi 100 SDS air compressor, Failing FM45 5 x 6-1/4” mud pump, 3-3/8” x 23-1/2’ kelly, air clutches, hydraulic pulldown, 5-1/4” retractable rotary table, Bean water injection, breakout tongs, 400’ of 20’ pipe, 3 hyd leveling jacks   Price:  $60,000

 

FAILING 1250 HOLEMASTER  (Ref#1276N)  Manufactured 1972, mounted on 1972 International F210D tandem axle truck with 250 Cummins engine, LeRoi 100 SDS air compressor, Failing 5 x 6-1/4 mud pump, 23-1/2’ kelly, hydraulic pulldown, Bean water injection, 5-1/4” retractable rotary table, 400’ of 2-7/8” x 20’ drill pipe, 20’ drill collar, one owner/operator, retiring  Price:  $73,000

 

FAILING 1250  (Ref#8204N)  3 x 4 centrifugal mud pump, LeRoi 50 SDS air compressor, pulldown, air clutches, new 2003 Mayhew 8” retractable table, new 3-3/8” kelly, breakout tongs, water injection, heavy duty 44,000# derrick, 3 hyd leveling jacks, 300’ of 2-3/8 IF x 20’ drill pipe, good condition, currently drilling, stored inside  Price:  $70,000

 

FAILING 1250  (Ref#6410N)  Manufactured 1974, Wheatley 1036 mud pump, Ford Cat diesel engine (replaced one years ago), 225’ of 2-7/8 API IF 15’ drill pipe, 280’ of 20’ 2-7/8” API IF drill pipe  Price:  $80,000

 

FAILING 1250  (Ref#7684N)  Manufactured 1973, 140/85 compressor, 5 x 6 mud pump, 6” retractable table, mounted on Ford 880 tandem axle truck w/534 gas engine, PTO, 23’ kelly, hydraulic pulldown, mechanical clutches, breakout wrench, swivel, 3 hydraulic leveling jacks, 300’ drill pipe, good condition  Price:  $78,500

 

FAILING 1250  (Ref#15562)  Manufactured 1970’s, mounted on 1980’s Kenworth truck with 400 Cummins engine, PTO, 500/250 air compressor, 5 x 6 Failing mud pump, 5-1/4” retractable table, good condition  Price on Request

Also available:  Ford tandem axle water truck, 2500 gal tank, 350 Cummins engine, 20’ pipe racks, 4-5 year old bed

 

FAILING 1250  (Ref#13862)  Manufactured 1976, 3 drums, air assist controls, mounted on 1982 tandem axle International truck w/PTO, 671 Detroit diesel, 3” x 23’ kelly, 7-1/2” retractable rotary table, 5 x 6 Gardner Denver duplex mud pump, no extra tools  Price:  $80,000

 

FAILING 1250  (Ref#13084)  mounted on 1985 International 1954 w/466 diesel engine, 5 & 2 transmission, 4-1/2 x 5 Gardner Denver mud pump, 250’ drill pipe, breakout tongs, currently drilling  Off Market

 

FAILING 1250  (Ref#12944)  Manufactured 1972, 5 x 6 Failing mud pump, auxiliary compressor, 5-1/4” retractable rotary table, mounted on 1972 GMC truck with Cat 3208 diesel engine, PTO, breakout wrench, tools, drill pipe, good condition  Price:  $57,500

 

FAILING 1250  (Ref#1276N)  Manufactured 1972, mounted on original truck 1972 IHC F210D tandem axle, 250 Cummins, LeRoi 100SDS air compressor, Bean injection pump, Failing 5 x 6-1/4 mud pump, 23-1/2’ kelly, hydraulic pulldown, well equipped and maintained, good reliable unit, owner operated  Price:  $70,000

 

FAILING 1250  (Ref#14609N)  Manufactured 1971, 5 x 6 duplex mud pump, 300/125 air compressor, 3-1/2” x 23’ kelly, 13” retractable table, 300’ of 2-7/8” x 15’ Mayhew Junior drill pipe, triple drum (one drum reworked), chain pulldown,  Price:  $40,000

 

FAILING 1250  (Ref#5924)  Manufactured 1971, 3 x 4 Mission pump, 100 SDS air compressor, mounted on 1973 Autocar with 8V71 Detroit diesel, rebuilt engine, some 2-7/8” pipe available  Price:  $100,000

 

FAILING 1250  (Ref#1471n) 1971, 5 x 6" Gardner Denver mud pump, 5-1/2" retractble rotary table, 3 hydraulic leveling jacks,  4-3/8" x 25' round fluted kelly,  32' mast, 20' drill rod rack with slide (holds 460' of 3-1/2" drill rod), 2" Little Giant swivel, On tandem axle 1978 Ford LT9000 with rebuilt 671 Detroit and 10 speed transmission, Hydraulic breakout cylinder and bit breakers, double line kelly, double hoisting line, sandline, 300' of 2-7/8" IF drill rod,  Hydraulic chain pulldown, 2-3/8" - 3-1/2" LF breakout tongs              Price:  $58,000

 

FAILING 1250  (Ref#4486)  Manufactured 1966, 5 x 6 mud pump, 5-1/4” retractable table, 3-1/8 x 23’ round fluted kelly, air clutches, mounted on tandem axle Autocar with 230 Cummins engine, currently drilling   Price:  $82,500

Also available at extra cost:   1976 Chevy Bruin tandem axle truck w/230 Detroit diesel and 2000 gallon round Griffin tank  OFF MARKET

 

FAILING 1250  (Ref#10364)  5 x 6 Gardner Denver mud pump, retractable table, 2 rear hydraulic leveling jacks, chain pulldown, rod box, mounted on 1982 Chevy Kodiak tandem axle truck with Cat 210 diesel engine, 200’ of 2-7/8” x 15’ drill pipe  Price:  $45,000   Price reduced:  $30,000

 

FAILING 1250  (Ref#6991N)  Manufactured 1962, 6 x 6 Whealy pump, mounted on 1971 Kaiser Military 6x6 truck with 250 Cummins, PTO, 7-1/2” Mayhew retractable table, developmental air 500/50, 3 leveling jacks, mechanical clutches, 200’ rod, drilling daily  Price:  $140,000

 

FAILING 1250  (Ref#11012N)  manufactured 1960’s, mounted on 1982 Ford L9000 truck with Cat 3208 engine in truck, PTO, (2) 5 x 6 mud pumps, pulldown, 460’ of 2-3/8” IF thread pipe, good condition, currently drilling  Price:  $80,000

 

FAILING 1250  (Ref#1825N)  manufactured 1960’s, mounted on 6 x 6 Mack truck, no mud, no air, rebuit drawworks, new swivel, PTO driven, diesel engine, 400’ drill pipe, rig needs some work  Price:  $26,500

 

FAILING 1250  (Ref#1921Na)  1974, mounted on 1982 Chevy truck with gas engine, PTO, 3 x 4 centrifugal pump, stabilizers, fully tooled, 7-7/8” bit, 280’ drill pipe, currently drilling   Price on Request

 

FAILING 1250 (Ref#9040N) Manufactured 1966, PTO driven, mounted on 1966 Ford T850 with 534 gas engine (needs a little TLC) 5 Ό” retractable table, 3 ½” x 23’ Kelly, hydraulic pulldown, mechanical clutches, breakout wrench, 5 x 6 mud pump, 50 SDS Leroi compressor,  1 front 2 rear hydraulic leveling jacks, no pipe or tools  Price:  $35,000

 

FAILING 1000  (Ref#319N)  3 x 4 Gardner Denver mud pump, LeRoi 100 SI compressor, PTO, mounted on 1979 International 2-ton tandem axle truck with diesel engine, 3-1/2” kelly, 7-1/2” fixed table, 3 hydraulic jacks, pipe rack, freshly paint5ed, mechanical pulldown, 300’ of 2-7/8” x 20’ drill pipe with 2-3/8 IF, 30” rubber tracks for rig

1982 750/125 LeRoi air compressor, Detroit diesel (replaced with ony 100 hours), mounted on 2-10# axle trailer, pintel hitch

Package Price:  $97,500

 

FAILING 1000  (Ref#1285N)  4-1/2 x 5 Gardner Denver mud pump, no air compressor, mounted on 1969 International 190 single axle truck, 6 cyl gas engine, PTO, 2 drill collars, 300’ drill pipe, pulldown, mechanical clutches  Price:  $45,000

 

FAILING 750  (Ref#1043N)  mounted on 1985 Ford single axle truck with gas engine, PTO, 5 x 6 Gardner Denver mud pump, 5-1/4”retractable table, pulldown, breakout wrench, mechanical clutches, 3” kelly, 2 winches, 2 screw jacks, 400’ of 2-3/8” x 10’ drill pipe, fully tooled,  Price:  $32,500

Also available at additional cost:  Gardner Denver air compressor with 6V71 Detroit engine, can be mounted on rig

 

FAILING 750  (Ref#15044)  mounted on 1985 Ford F700 single axle truck with gas engine, complete rig, 4-1/2 x 5 mud pump, gas deck engine, 24’ kelly, rod rack, hydraulic pulldown, some pipe   Price:  $28,500

 

FAILING 750  (Ref#11002)  Manufactured 1964, mounted on GMC truck w/gas engine, PTO, 7” swing away table, 3 x 4 piston pump, (6) 15’ drill rods  Price:  $24,500

 

FAILING 750  (Ref#14992)  Manufactured 1962, 4-1/2 x 5 mud pump, mounted on 1978 International truck w/348 engine (needs work), runs 15’ rods  Price:  $22,500

 

FAILING F750  (Ref#11337)  Manufactured 1960’s, PTO, mounted on 1979 Ford F700 truck 4-1/2 x 5 Gardner Denver mud pump, 5-1/2” retractable rotary table, good condition, currently drilling  Price of Request

 

FAILING 250  (Ref#10430)  Manufactured 1965, 4-1/2 x 5 Saline mud pump, 20’ mast, non-retractable rotary table, mounted on 1978 Ford with 400 hp gas engine, rig in good condition, truck in poor condition, 3 hydraulic leveling jacks, breakout tongs, subs  Price:  $22,000

 

FAILING 250  (Ref#11336)  Manufactured 1960, PTO, mounted on 1970 Bombadier tracked carrier (rear axle needs replacing), V6 engine, 4-1/2 x 5 Gardner Denver mud pump, 5-1/2” retractable rotary table, no pipe, good condition  Price:  $15,500

 

FAILING FA100  (Ref#14993)  soil testing rig converted to mud, 1965, centrifugal pump, gas engine, 100 – 150’ 4” casing, 1-1/2” x 10’ L rod, on 1965 Ford 4x4, PTO, hydraulic system, winch  Price:  $26,000

 

1250 FAILING CFD-1B  (Ref#7547)  100 S2 Leroi compressor, new 500 gallon water tank, 7-1/2" rotary table (non-retractable), injection pump, on 1993 Kenworth truck, 300 L10 motor, 3TA92 Fuller power divider, 24" tires, choice of eithr 280’ of 3-1/2” or 4” flush joint drill pipe,   Off Market

Also available:  5-1/4" retractable rotary table for 1250 with new bearings, tested and ready to go:  $5,500

 

FAILING CFD-1  (Ref#12659N)  PTO, mounted on Gemco 300 buggy with Detroit diesel engine, 4-1/2 x 5 mud ump, no air, 5” stationary table, 13’ kelly, pulldown, mechanical clutches, 2 rear hydraulic leveling jacks, fully refurbished and ready to go  Price:  $95,000

Tools and pipe available at extra cost

 

FAILING CFD-1B  (Ref#11398N)  mounted on 1986 Mack tandem axle truck with diesel engine, water injection, some pipe  Price:  $50,000

 

FAILING CFD-1  (Ref#12147)  Manufactured 1955, 5 x 6 Gardner Denver piston pump (low hours), 3 x 4 Mission Magnum centrifugal pump, mounted on 1986 Ford F8000 truck with Cat 3208 diesel engine, 5 speed transmission, 2 speed rear axle, 2 rear leveling jacks, 20 jts of 2-3/8” x 15’ Mayhew Reg drill pipe, no tooling, good condition  Price:  $43,000

 

FAILING CFD-1  (Ref#1957N)  5 x 6 Wheatley mud pump, Gardner Denver developmental air, hydraulic pulldown, mechanical clutches, stabilizer, mud pan, 3-1/2” kelly, stationary table, mounted on Ford Louisville tandem axle truck with 290 Cummins engine, PTO, 2 rear hydraulic jacks, 200’ of 3-1/2” x 20’ drill pipe, good condition, currently drilling  Price:  $65,000

 

FAILING CFD-1  (Ref#13243)  mounted on 1978 GMC truck w/rebuilt motor  Price:  $35,000

 

FAILING CFD-1  9Ref#13262)  Manufactured 1968, mounted on 1968 Ford F600 truck, 5 x 6-1/4 mud pump, 256 LeRoi air compressor, good condition  Price of Request

 

FAILING CFD-1B (Ref#3990)  Manufactured 1973, 6 x 4-1/2 FXG Failing piston mud pump, 5-1/4” fixed table, hydraulic chains, well maintained, Mounted on Ford F600 single axle with 391 Cleveland gasoline engine, 3 leveling jacks, PTO, 200’ of 2-3/8” drill pipe  Price:  $50,000

 

FAILING CFD-1B  (Ref#10898)  3 drum drawworks, 5-1/2 table, 23’ kelly, 5 x 6 Failing mud pump, hydraulic pulldown, mounted on 1968 Kaiser Jeep Cargo truck, 6x6 dual tandem, 1100x20 ties, 2 rear leveling jacks, 40,000 lb. Front mounted winch, truck rebuilt in 1978 with new Cummins diesel (522 hours)  Price:   100,000

 

FAILING CFD-1B  (Ref#14418)  3 drum drawworks, 7-1/2” retractable table, 27’ kelly, Failing mud pump, breakout wrench, 275 cfm air compressor, pulldown, mechanical clutches, mounted on 1967 International truck w/gas engine (needs work), 3 hydraulic leveling jacks, 460’ of 2-7/8” x 20’ drill pipe, good condition  Price:  $40,000

 

FAILING CFD-2  (Ref#8548)  mounted on Gemco 300 buggy, 4 cyl Detroit diesel,  Price:  $50,000

 

FAILING CF-B1  (Ref#9977)  Manufactured 1981, LeRoi air compressor, 5 x 6 Gardner Denver duplex mud pump, on Ford 9000 with 350 Cummins diesel engine, 4 leveling jacks, 18’ kelly, cleaned and painted, excellent condition  Off Market

 

FAILING CF15  (Ref#2171N)  5 x 6-1/4” Failing mud pump, 880A air compressor, mounted on 2004 Peterbilt all wheel drive single axle truck with diesel engine, sandline, 5-1/4” retractable table, air clutches, chain pulldown, breakout wrench, good condition  Price:  $345,000

 

FAILING CF-15  (Ref#1274N)  Manufactured 2001, 5 x 6 mud pump, 7-1/4” retractable table, air clutches, pulldown, breakout tongs, 33’ mast, 3” kelly, mounted on International tandem axle w/530 Huey Intl diesel engine, PTO, 4 hydraulic leveling jacks, good condition  Price:  $260,000

Pipe available at additional cost

 

FAILING CF-15  (Ref#2158Na)  Manufactured 1994, 5 x 6 piston mud pump, LeRoi air compressor, mounted on 1994 International single axle truck with DT466 engine, PTO, 7-1/2” rotary table, 24’ x 2-7/8” fluted kelly, mechanical clutches, no pulldown, no breakout tongs, 3 hyd leveling jacks, good condition, currently drilling, no pipe or tools  Price:  $70,000

 

FAILING CF-15  (Ref#2246N)  Manufactured 1985, 100/50 air compressor, 5 x 6-1/4” Failing mud pump, mounted on 1991 Kenworth truck with 8V92T, 36’ mast, rebuilt rotary table, swivel and transmission, speed $50,000 on rebuild, 420’ of 3-1/2” x 20’ drill pipe  Price:  $275,000

 

FAILING CF15 HOLEMASTER  (Ref#13414)  Triple drum drawworks, Air clutches, (2) drums 7” x 8-3/4”, Brakes 16” x 6”, Clutches 14” 3 plate, Third drum 7” x 24”, Chain pulldown (2) 1-1/2” pitch chains, Mounted on 1996 International tandem axle powered by DT466 diesel engine, PTO drive, All new tires, 4 hydraulic leveling jacks, 38’ X 60,000# hydraulically raised mast, 7-1/2” hydraulically retractable table opens to 14” diameter, Table speeds:  0 – 115 rpm, 5-1/2” x 8” duplex mud pump mechanically operated with air clutch, Water injection system, Developmental air compressor 50 SDS, 500’ of 2-7/8” x 20’ drill pipe New 2003 (200’ never used)  Dimensions/weight:  38’ long x 8’ wide x 13’ high – 65,000#.  Rig was rebuilt in 2003 including:  Cleaning, paining refurbishing, New controls and gauges, New fluid end parts, Hoses and liners replaced, Hydraulics reworked.  Rig is in excellent condition  

Off Market

 

FAILING CF15  (Ref#1081N)  mounted on 1992 International truck with DT466 engine, PTO, 5 x 6 mud pump, 24’ kelly, pulldown available (was removed), mechanical clutches, 2 rear hyd leveling jacks, good condition  Price:  $65,000  Pipe available at extra cost

 

FAILING CF15  (Ref#1506N)  Manufactured 1980, 4-1/2 x 6 mud pump, 8-1/2” retractable table, 38’ mast, mounted on 1980 Ford F900 truck with propane engine, transfer case, 1200’ of pipe, currently drilling

1987 Chevy 660 water truck, 1600 gallon poly propalene tank, grout pump

JCB210 SL 4x4 backhoe

Package Price:  $100,000

 

FAILING CF15  (Ref#2569N)  Manufactured 1979, 5 x 6 Gardner Denver mud pump, air compressor for drilling, 8” retractable table, 2-3/8” kelly, 26’ mast, pulldown, mechanical clutches, Myers water injection, mounted on GMC Brigadier truck with 3208 Cat engine, 3 hydraulic leveling jacks, 500’ , 3-5/8 x 15’ drill pipe, bits, subs, good condition  Price:  $105,000

 

FAILING CF15  (Ref#4653Na)  Manufactured 1978, mounted on 1995 International truck with 3208 Cat engine, PTO, 6 x 6 Wheatley mud pump, 50 SDS LeRoi air compressor, Myers water injection, 4-1/8” kelly, 5-1/4” retractable table, Little Giant 2-1/2” swivel, pulldown, air clutches, 3 hydraulic levelign jacks, 300’ of 2-3/8 x 20’ FEDP, breakout wrench, slips, subs, etc  Price:  $130,000

1994 MACK WATER TRUCK  (Ref#4653Nb)  250 hp Cummins engine, 10 speed transmission, 2000 gal round steel tank, no crane or welder, Mason grouter, 20’ bed, no toolbox, pipe rack  Price:  $39,500

 

FAILING CF15  (Ref#5140N)  Manufactured 1978, mounted on 1977 International 5000 truck with diesel engine, PTO, (2) 5 x 6-1/4” mud pumps, air clutches, air drawworks, pulldown, 38’ mast, 5-1/4” retractable table, 3-3/8” kelly, water injection, breakout cylinder, 1 front 2 rear hydraulic leveling jacks, 700’ of 2-3/8” x 20’ drill pipe, excellent condition, currently drilling  Price:  $110,000

 

FAILING CF15  (Ref#7570Na)  Manufactured 1978, mounted on International 1850 w/DT466 engine, PTO, 5 x 6-1/4” mud pump (low hours), 5-1/4” retractable table, 3” fluted kelly, Little Giant swivel, air clutches, pulldown, heavy duty 35’ mast, 3 hydraulic leveling jacks, excellent condition, one owner rig, well maintained

Price, rig only:  $150,000

Also available:  Flatwater Fleet Water Truck  (Ref#7570Nb)  2700 gallon tank, mounted on 1981 International 2564 with DT466 engine, 6000# crane, underbody toolboxes, pipe racks  Price:  $45,000

 

FAILING CF15  (Ref#1618N)  Manufactured 1977, (2) 5 x 6 Gardner Denver mud pump, 8” retractable table, 3-3/8” x 25’ kelly, pulldown, air clutches, breakout wrench, rod box, mounted on 1999 International tandem axle truck with DT466 engine, PTO, 4 hyd leveling jacks, some pipe and tools, good condition, ready to go  Price:  $120,000

 

FAILING CF15  (Ref#8561N)  100 SDS LeRoi air compressor, 5 x 6-1/2” mud pump, 7-1/2” retractable table, 4-1/8” kelly and 3-3/8” kelly, mounted on 1977 International Loadstar 1850 with DT466 engine, hydraulic pulldown, mechanical clutches, hydro pump, breakout tongs, water swivel, sandline, well maintained, excellent condition  Price:  $85,000 

300’ of 3-1/2” x 20’ pipe available for extra cost.

 

FAILING CF15  (Ref#5183N)  Manufactured 1975, 5 x 6 Failing pump, LeRoi 6 cyl air compressor, 7-1/2” retractable DSM table, Little Giant swivel, breakout wrench, mounted on 1992 Ford L9000 truck with 300 Cummins engine, PTO, 300’ of 3-1/2” x 20’ drill pipe, fully tooled, 4-1/4” kelly, mechanical clutches, pulldown, 38’ mast, water injection, bits, subs, stabilizers, excellent condition, completely overhauled  Price:  $170,000

 

FAILING CF15  (Ref#8369N)  Manufactured 1974, LeRoi 50S2 air compressor, 5 x 6 mud pump, 5-1/4” retractable table, 3-3/8” fluted kelly, 3 hydraulic leveling jacks, pulldown, mechanical clutches, breakout wrench, mounted on 1974 International tandem axle truck with diesel engine (overhauled less than 1000 hours), 200’ of 2-7/8” x 20’ drill pipe  Price:  $95,000

 

FAILING CF15  (Ref#3272N)  Manufactured 1973, PTO, recently rebuilt, mounted on 1973 International 2050 tandem axle truck with 6V53T Detroit diesel engine, (2) FM45 5x6 pumps, 2” Little Giant swivel, DSM 7-1/2” retractable rotary table (mfg 2003), air clutches, breakout wrench, fluted  25’ kelly, hydraulic pulldown, 42’ hydraulically raised mast, 4 hydraulic leveling jacks, collars, subs, 840’ of 2-7/8” x 20’ 2-7/8IF drill pipe, good condition, currently drilling  Price:  $115,000

 

FAILING HOLEMASTER CF15 (Ref#13374Na) Manufactured early 1970’s, PTO, mounted on 1980 Ford 9000 with 350 Cummins engine, rebuilt 5 x 6 Ό mud pump, rebuilt clutch and chain case, 7 ½” retractable table, pulldown, mechanical clutches, breakout wrench, 4” Kelly, 27’ mast, 2 rear hydraulic leveling jacks, pipe racks, toolbox, 300’ of 20’ x 31/2” flush wall drill pipe  Price:  $70,000

1980 FORD 900 WATER TRUCK (Ref#13374Nb) Cat 3208 engine, 1500 gallon steel octagonal tank, toolboxes, no crane or welder

Package Price for rig & water truck:   $78,500

 

FAILING CF-15  (Ref#15495)  Manufactured 1974, LeRoi SD-100 air compressor, 5 x 6 mud pump, mounted on 1974 Paystar 5000, rebuilt motor (70 hours), 5-1/4” retractable table, 3 jacks, excellent condition  Price:  $85,000

 

FAILING CF-15   (Ref#10243)  Manufactured 1972, 450/200 LeRoi 2-stage air compressor, 5 x 6 Gardner Denver mud pump, 8-1/2” retractable table, hydraulic pulldown, mechanical clutches, mud pan, mounted on 1970 Peterbilt truck with new 450 Cummins engine, PTO, 5 hydraulic leveling jacks,  no tools, no pipe, drills daily, good condition

1973 GMC SUPPORT TRUCK  3000 gallon aluminum tank, Allison automatic transmission, 23,000 original miles, (was old Firetruck), excellent condition, stored inside  Price:  $105,000  PRICE REDUCED:  $70,000

 

FAILING CF15  (Ref#260Nb)  mounted on 1979 GMC truck (cabneeds work), 10 wheel truck, diesel engine, PTO, 5 x 6 mud pump, LeRoi air compressor, 20’ rod carrier, 3 hyd leveling jacks, no tools or pipe POR

 

FAILING CF15  (Ref#260Nc)  mounted on 1981 International truck, DT466 diesel engine, PTO, 5 x 6 mud pump, small air compressor, 3 hyd leveling jacks, no tools or pipe  POR

 

FAILING CF15  (Ref#1472N)  Manufactured 1971, mounted on 1971 International truck with Detroit 6V92TA (305 hp) engine, Fuller 10 speed transmission, LeRoi 100S2 compressor, Failing FM45 5” x 6-1/4” mud pump, hydraulic chain pulldown, mechanical friction clutches on the draworks, 3-5/8” OD fluted kelly, 8-1/2” retractable rotary table, 3 hydraulic leveling jacks, drill string weight indicator, hydraulic utility hoist, no drill pipe rack  Price:  $75,000

 

FAILING CF15  (Ref#2431N)  5 x 6 Gardner Denver mud pump, LeRoi piston air compressor, mounted on 1970 Peterbilt with 450 Cummins engine, 8” retractable rotary table, air clutch, drawworks totally rebuilt 3 years, 190’ pipe plus mud stabilizer, 5 jacks  Price:  $60,000

 

FAILING CF15  (Ref#12301N)  Manufactured mid 1970’s, mounted on Ford L9000 truck with 6V71 Detroit engine, PTO, 5 x 6 mud pump, developmental air compressor, water injection pump, 5” stationary table, 23’ kelly, chain pulldown, air clutches, (no breakout wrench), 2 rear hydraulic leveling jacks, 400-500’ of 2-7/8” x 20’ drill pipe, good condition, currently drilling  Price on Request

 

FAILING CF15 (Ref# 8739Nc) Manufactured 1976, 5 x 6 mud pump, developmental air   Price on request

 

FAILING F10  (Ref#6470)  Manufactured 1990, mounted on Ford L8000 tandem axle truck with Cummins 5.8 6 cyl diesel engine, leveling jacks, Moyno 3L8 pump, Gardner Denver 5 x 6 dulplex mud pump, Funk-o-Matic increases the 15,000 ft/lb torque to 30,000 ft lbs., sitting for 2 years, no tools  Price:  $100,000

 

FAILING F10  (Ref#2135N)  Manufactured 1990, 4 x 5 piston pump, 3L6 Moyno, Cummins 6BT5.8 diesel deck engine, wiggle tail slide base, 4 hyd leveling jacks, 2 auger racks, 25,000# pulldown/pullback, 12,000# rotary torque, mounted on 1990 Ford LN9000 tandem axle truck with LTA10 250hp Cummins diesel, 14708LL transmission, approx 17,000 miles, 16,000# front and 40,000# rears, 24,000# capacity front winch,  Price:  $120,000

 

FAILING F10WT  (Ref#3671N)  Manufactured 1990, 4 x 5 piston pump, 3L6 Moyno pump, Cummins 6BTS5.8 diesel deck engine, wiggle tail, slide base, 4 hydraulic jacks, 2 auger racks, 25,000# pulldown/pullback, 12,600# rotary torque, mounted on 1990 Ford LN9000 tandem axle chassis with LTA10 (@250 hp), Cummins diesel and 14708LL transmission, approx 17000 miles, 16,000# front and 40,000# rears, 24,000# capacity front winch, tires are 385R/22 fronts, PowerArc 5500 generator/welder, 35’ (7 pieces) 8” HS auger  Price:  $120,000

 

FAILING F10  (Ref#7734N)  Manufactured 1989, Cummins deck engine, 3 winches, cathead, safety driver, 3L6 Moyno pump, 140# auto hammer, 250 gallon water tank, a\uger rack, toolbox, mounted on GMC tandem axle truck with Cat 3208 engine, good condition  Price:  $85,000

 

FAILING F10-WT  (Ref#629N)  Manufactured 1988, 5.9 Cummins deck engine angle package, 12,000# single line winch, 5 x 6 Failing mud pump, 25,000# pullback 8,300 hours, excellent 200-600’ mud hole rig, 300’ of 3-1/2” x 10’ drill rod  Price:  $125,000

 

FAILING F10  (Ref#8708N)  Manufactured 1989, mounted on International tandem axle truck, 38,000 miles, low hours on rig, Cummins deck engine, 10” and 12” augers, 400’ drill rod, Gardner Denver 5 x 6 mud pump, Waukesha engine powered mud pump, cathead, fastline, mainline, low hours, rig is like new  Price:  $95,000

 

FAILING F10  (Ref#10645)  Manufactured 1989, mounted on Ford LN8000 with diesel engine (35,000 miles), diesel engine on deck, 3 winches, hydraulic wrench, mud pump  Price:  $100,000

 

FAILING F-10-WT  (Ref#2262N)  Manufactured 1987, top drive auger rig, mounted on S1900 tandem axle truck with DT466 diesel engine, Fuller Road Ranger 10 speed transmission, 77831 miles on truck, Cummins 5.9L diesel on deck with 2382 hours, 2 winch lines, new 2” hydraulic Bowie mud/grout pump, includes all new components as follows:  100’ of 4-1/2 triple key heavy duty auger, 100’ of NWJ x 5’ rods, (2) 4” split tube continuous sample barrels, (2) auger bits, (2) Apex bits, replacement bullets for bits, numerous adaptors for sample equipment 

Price with tooling:  $85,000   Price without tooling:  $65,000

 

FAILING F-10-WT  (Ref#10361N)  Manufactured 1987, Cummins 8.3CT deck engine, angle drilling, wiggle tail, 15,000 ft/lb torque @ 0-934 rpm, 9-3/4” spindle opening, 25,000# pulldown and retract force, 11’ tophead drive travel, mounted on International truck with DT466 engine, completely tools with new 4-1/4” augers and split spoons  Price:  $145,000

 

FAILING F10  (Ref#3670N)  Manufactured 1986, Rebuilt Cummins deck engine, mounted on 1986 International, approx 25000 miles, Detroit DT466, 5 speed transmission, 160’ drill pipe, 4’ x 10’ subs, 100’ 6” auger split spoons, drop hammer, 6” bit, 8” bit, 3 x 4 mud pump, 400 gallon water tank, 3” suction hose, 15” hole in table, rig slides side to side and forward and back, 3 leveling jacks, 3 hydraulic winches  Price:  $80,000

 

GEFCO F8  (Ref#13559)  Manufactured 1987, mounted on International Paystar 5000, 1331 casing hammer, screw compressor  Price:  $105,000

 

FAILING F7  (Ref#14409)  Manufactured 1989, hi-torque, 2 hoists, auger racks, cathead, water tank, leveling jacks  Price:  $55,000

 

FAILING F6  (Ref#3711N)  Manufactrured 1994, mounted on Mack 6 wheel drive truck with Mack diesel engine, PTO, big mud pump, in/out and side to side slide base, breakout wrench, auger rack, pipe racks, fully loaded  Price:  $75,000

 

FAILING F6  (Ref#12692)  diesel deck engine, mounted on 1990 Ford L8000 tandem axle truck with diesel engine, truck ok, rig poor,  Price:  $25,000

 

FAILING F6  (Ref#11439)  Manufactured 1990, 3L8 Moyno mud pump, Cummins diesel deck engine, 2 winch lines, CME sampling system, 3 solid sampling barrels, breakout wrench, side port swivel, angle drilling attachments, 2 swivel auger racks, driller’s stand, sliding drawworks (side to side, back and forward), mounted on 1989 tandem axle Kodiak 70 Sereis truck with Cat 3208 diesel engine, reverse flight augers for hollow steam augers, 150’ of 3-3/4” ID HD hollow stem, 100’ of 1-5/8” hex rod, (2) 3-3/4” bits, excellent condition  Price:  $85,000


 

 

Tel:  516-536-7375          Fax:  516-536-7317         rigs@sunmachinery.com