SUN MACHINERY CORP.

Call: 516-536-7375 /  516-536-7317 fax

rigs@sunmachinery.com

AUGERS

Acker XLS, Soilmax, ADII, Coremaster, MP-V C

AMS Power Probe 9630 Generation III

BRAINARD KILMAN (LONGYEAR)   BK51

CANTERRA  CT-550, CT450, CT-411, CT-312, CT-311, CT-350, CT-250, CT-150

CME   1250, 1050, 850, 750, 550, 450, 85, 75 (HT), 55, 45(B)(C)

FAILING F-10-WT  (Ref#15N)  Manufactured 1990, 28’ derrick angle feature with 11’ top drive stroke, LTA Cummins 240 hp deck engine (low hours), mounted on Ford L9000 truck, 4 hydraulic leveling jacks, 25,000# pulldown/pullback capacity, 4 x 5 duplex mud pump, Moyno 3L6 pump, 3 winches, 2 derrick rams,  Price:  $110,000

FAILING F10 (Ref#11968Nc) Manufactured 1990, mounted on International 4900 6x4 with DT466 engine, Gardner Denver 5x6 mud pump, Moyno 3L8 pump, 2 winches, deck mounted hydraulic drive 2000psi steam cleaner/power washer, toolboxes, auger rack  Price:  $210,000

FAILING F10  (Ref#8708N)  Manufactured 1989, mounted on International tandem axle truck, 38,000 miles, low hours on rig, Cummins deck engine, 10” and 12” augers, 400’ drill rod, Gardner Denver 5 x 6 mud pump, Waukesha engine powered mud pump, cathead, fastline, mainline, low hours, rig is like new  Price:  $95,000  PRICE REDUCED:  $80,000

FAILING F10  (Ref#10645)  Manufactured 1989, mounted on Ford LN8000 with diesel engine (35,000 miles), diesel engine on deck, 3 winches, hydraulic wrench, mud pump  Price:  $100,000

FAILING F-10-WT  (Ref#2262N)  Manufactured 1987, top drive auger rig, mounted on S1900 tandem axle truck with DT466 diesel engine, Fuller Road Ranger 10 speed transmission, 77831 miles on truck, Cummins 5.9L diesel on deck with 2382 hours, 2 winch lines, new 2” hydraulic Bowie mud/grout pump, includes all new components as follows:  100’ of 4-1/2 triple key heavy duty auger, 100’ of NWJ x 5’ rods, (2) 4” split tube continuous sample barrels, (2) auger bits, (2) Apex bits, replacement bullets for bits, numerous adaptors for sample equipment 

Price with tooling:  $85,000   Price without tooling:  $65,000

FAILING F-10-WT  (Ref#10361N)  Manufactured 1987, Cummins 8.3CT deck engine, angle drilling, wiggle tail, 15,000 ft/lb torque @ 0-934 rpm, 9-3/4” spindle opening, 25,000# pulldown and retract force, 11’ tophead drive travel, mounted on International truck with DT466 engine, completely tools with new 4-1/4” augers and split spoons  Price:  $145,000

FAILING F10  (Ref#3670N)  Manufactured 1986, Rebuilt Cummins deck engine, mounted on 1986 International, approx 25000 miles, Detroit DT466, 5 speed transmission, 160’ drill pipe, 4’ x 10’ subs, 100’ 6” auger split spoons, drop hammer, 6” bit, 8” bit, 3 x 4 mud pump, 400 gallon water tank, 3” suction hose, 15” hole in table, rig slides side to side and forward and back, 3 leveling jacks, 3 hydraulic winches  Price:  $80,000

FAILING F7  (Ref#14409)  Manufactured 1989, hi-torque, 2 hoists, auger racks, cathead, water tank, leveling jacks  Price:  $55,000

FAILING F6  (Ref#3711N)  Manufactured 1994, mounted on tandem axle Mack all wheel drive truck powered by Mack diesel engine, PTO to operate rig, Failing Model L100 4” x 5” duplex mud pump, in/out and side to side base, breakout wrench, auger rack, pipe rack, 70,000 miles on truck, 2000 hours on rig, new tires, removable mast  Price:  $60,000

FAILING F6 (Ref#9016Nb) Manufactured 1994, mounted on 1994 Ford FT900 tandem axle, Moyno 3L6 pump, auger racks, 300 gallon water tank, 4 winches plus cathead  Price:  $75,000

FAILING F6 (Ref#9016Na) Manufactured 1991, mounted on 1991 International 4900 single axle, Moyno 3L8 pump, auger racks, 300 gallon water tank, 2 winches plus cathead  Price:  $75,000

FAILING F6 (Ref#9576N) Manufactured 1991, diesel deck engine, mounted on 1991 International single axle truck with diesel engine (not all wheel drive), in-out and side to side slide base, Moyno 3L8 pump, Mission 4x3 mud pump, electric over hydraulic controls, 4 1/8” x 28’ Kelly, breakout wrench, safety driver, soil extruder, rod box, pipe rack, toolboxes, 3 winches, no auto hammer, no cathead, no tools or augers available  Price:  $70,000

Also available at additional cost: Chem Grout unit, electric start

FAILING F6 (Ref#11968Na) Manufactured 1990, mounted on 1990 International 4900 with DT466 engine, 2 winches, Moyno 3L8 pump, electric over hydraulic controls, deck mounted 2000psi steam cleaner/power washer, toolboxes, auger racks  Price:  $95,000

FAILING F6  (Ref#12692)  diesel deck engine, mounted on 1990 Ford L8000 tandem axle truck with diesel engine, truck ok, rig poor,  Price:  $25,000

GEFCO STRATASTAR  (Ref#5043N)  Manufactured 1995, mounted on 1995 International single axle truck with diesel engine, brand new PTO and transmission, 4 leveling jacks, Moyno 3L8 pump, auto hammer, 2 auger racks, breakout wrench, rod clamp, 250 gallon water tank, 3 winches (1,000#, 3,000# and 5,000#), can auger or mud drill, uses 4” x 5’ drill pipe  Price:  $80,000

FAILING 1500  (Ref#5286N)  set up for geothermal drilling, Ford 6 cyl diesel on deck, Failing FM45 5 x 6-1/4 mud pump, mounted on 1990’s Mack tandem axle truck with diesel engine, Moyno 3L6 pump, auto SPT hammer, 2-7/8” kelly, 7-7/8” table, hydraulic pulldown, mechanical clutches, 2 winches, 3 jacks, no rods, refurbished 3 years ago, 60 hours since refurbished  Price:  $90,000

INGERSOLL RAND A-300  (Ref#1586N)  mounted on 2001 Ford F650 single axle truck with Cummins diesel engine, PTO, in/out slide base, cathead, 4 hyd jacks, no mud, water tank, auger racks, toolbox, no tools or rod available  OFF MARKET

INGERSOLL RAND A-300 WITH SONIC DRILL HEAD  (Ref#10235N)  Manufactured 1994, 12” x 12” x 20’6” mast, 18,000# pulldown or pullback, Sonic drill head, head travel speed 50’ per minute, Chelsea side mount PTO, (3) hydraulic leveling jacks, mounted on Ford F700 truck with 5.7L Cummins diesel engine, 5-speed transmission, heavy duty overdrive, 50 gal fuel tank, 4.3 ratio rear end, 32,000# WVW, cab to axle 102”, power brakes, power steering, Cat pump 2520, Moyno pump 3L6 30 gpm/225 psi, “A” rod rack 54” x 15” x 7”, 3.5” x 5’ rod, 5-7/8” casing, controls and gauges, deck high, left side, 8000# hydraulic hoist 85’ per minute ½” x 60’, (2) toolboxes, hydraulic breakout wrench system 9”, 25’ long x 8’ wide x 10’9” H (derrick down), 20,000 lbs.  Price:  $195,000

INGERSOLL RAND A-300  (Ref#2128N)  Manufactured 1994, mounted on Ford single axle diesel truck, 3 hyd leveling jacks, main winch, 6’ extended mast, 18,000# pulldown, 6-5/8” auger guide, speed and torque of tophead, Range 1  8000 ft/lb – 75 rpm;   Range 2  4500 ft/lbs  0 – 110 rpm,  Range 3  2250 ft/lbs  0-215 rpm, 8000# hoist set for ½”  Price:  $65,000

INGERSOLL RAND A-300  (Ref#3529N)  Manufactured 1993, mounted on 1993Ford truck, PTO driven, 3L8 Myno pump, in/out slide base, high rail gear, good running condition, no tools  Price:  $70,000

INGERSOLL RAND A-300  (Ref#5938)  Manufactured 1992, 3L6 Moyno pump, Mounted on Ford 700 with Cummins diesel engine, PTO, 3 jacks, 19’ telescoping mast, 8’ head travel 8,000 ft/lb, hoist, cathead, slide base, in-out, side to side slide base, wiggle tail, (2) auger racks, (2) tool boxes   Price:  $75,000   Off Market

INGERSOLL RAND A-300  (Ref#3798N)  Manufactured 1992, mounted on 1992 Ford F700 single axle truck, 3 leveling jacks, 6.6 ltr diesel engine, PTO, 8,000# and 6,000# winch, 12’ mast, 18,000# pulldown and pullback, 16” sliding base,  cathead, 3L6 Moyno pump, 100 gallon water tank, built-in auger racks, safety hammer (not auto hammer), 40’ of AWJ rods, core barrel

Price rig only:  $30,000  Price with truck:  $40,000

ACKER SOILMAX  (Ref#1003N)  Manufactured 1990, Duetz 4 cylinder diesel deck engine, mounted on 4800 4x4 International with diesel engine, 4 hoists, new Moyno 3L8 pump, lateral slide, slide base, front mounted winch runs PTO truck, new clutch, new hydraulic pump, new jacks, new hydraulic motor, ready in March 2007   Price: $130,000

ACKER SOILMAX  (Ref#5067N)  Manufactured 1990, Deutz diesel on deck, mounted on Gotrack rubber tracks wutg steel cleats, Cummins diesel engine, 3L8 Moyno, auto chuck, auto breakout, in/out side to side  Price:  $95,000

ACKER SOILMAX (Ref#3495N)

Manufactured 1987, 10,000 high torque, 24' long mast, 6' stroke, 1 main winch, 2 auxiliary winches, 3 tool boxes, pipe racks, 140# safety hammer, mounted on 1987 GMC 7000 all wheel drive with V8 366 gasoline engine, in-out and side to side slide base, Moyno 3L8 (450 gpm @ 225 PSI) pump, 3 hydraulic leveling jacks, rebuilt hydraulics 2007

Tools:

50’ of 3 ¼” HSA, Augers

Misc spoons:  3" spoon w/ several new shoes, subs, bits, roller bits. 

Hoist Equipment:  (2) Packers & associated tubing

Price for rig only:  $60,000

Price:  $65,000 for All

ACKER SOILMAX  (Ref#4850N)  Deutz diesel deck engine, Moyno 3L6 pump, in/out and side to side, 2 winches, mounted on 1988 International 1654 truck (not 4 x 4) with diesel engine, 250 gallon water tank, 3 hydraulic leveling jacks, toolboxes, pipe rack, auger racks, cathead  Price:  $80,000  PRICE REDUCED:  $65,000

Tools/augers available

ACKER SOILMAX (Ref#3923Na) Deutz diesel deck engine, mounted on 1997 Freightliner FL70 with Cummins diesel engine, cathead with safety hammer, in-out and side to side slide base, 2 winch lines, 10000 ft/lbs, 250 gallon water tank, auger racks, toolboxes  Price: $82,000  PRICE REDUCED:  $65,000

ACKER SOILMAX (Ref#3923Nb) new Deutz diesel deck engine, mounted on 1996 Freightliner FL70 with Cummins diesel engine, Diedrich auto hammer, in-out and side to side slide base, new Moyno 3L6 pump, 10000 ft/lbs, 250 gallon water tank, auger racks, toolboxes  Price:  $105,000  PRICE REDUCED:  $60,000

ACKER XLS  (Ref#1057N)  Manufactured 2005, track mounted, set up for auger and coring, 6 cyl Duetz diesel engine, cathead, sandline, angle capability, breakout wrench, Moyno 3L6 pump, 140# auto hammer, 4 hyd leveling jacks, no tools, good condition  Price:  $160,000

ACKER XLS (Ref#14632Nb) Manufactured 1991, skid mounted, Moyno 3L4 pump, 6000# winch, slide base, cathead  Price:  $62,500

ACKER ADII (Ref#14632Na)   Manufactured 1989, mounted on 1996 International 4900 with diesel engine, Moyno 3L8 pump, 10000# wireline winch, 250 gallon water tank, toolbox  Price:  $100,000

ACKER AD-II  (Ref#325N)  Manufactured 1987, 4 cyl Duetz diesel deck engine, mounted on 2002 International 4400 with DT466 diesel engine, cathead, 3L6 Moyno pump, in/out slide base, 300 gal plastic water tank, 3 hyd leveling jacks, auger racks, toolboxes, no auto hammer or breakout wrench, currently drilling  Price:  $42,500

Tools and augers available at additional cost

ACKER AD-II  (Ref#1802N)  skid mounted, 172 Ford 4 cyl gas engine, manufactured 1976  Price:  $22,000

ACKER AD-II  (Ref#9399N)  Manufactured 1973, gas engine on deck, mounted on 1990 F800 4 wheel drive truck with gas engine, fully tooled, running condition  Price:  $60,000  OFF MARKET

CME 1250  (ref#1120N)  track mounted, excellent condition  Price:  $300,000

CME 850 (Ref#1237N) Manufactured 1998, only 3200 hours,  Cummins 4BT deck engine, mounted on tracks, in-out and side to side slide base, cathead, Moyno 3l* pump, 10000# Pullmaster winch, (2) 3200# aux. Winches, wireline, breakout wrench, hydraulic chuck with 5” fluted Kelly, rod holder, 3 hydraulic leveling jacks, no tools or augers available  Price:  $170,000

CME 850 (Ref#11920N) Manufactured 1997, Cummins deck engine, track mounted, in-out and side to side slide base, 23’ quick disconnect mast, angle capability, 140# auto hammer, breakout wrench, no cathead, Moyno 3L6 pump, 3 hoists, water tank, 3 hydraulic leveling jacks  Price:  $135,000

CME 850 (Ref#4060N) Manufactured 1996, 4 cylinder Cummins engine, fresh rebuild on engine and transmission, track mounted, auto hammer, Pullmaster winch, 2 tooling winches, wireline, hydraulic locking fluted Kelly, rod holder, breakout wrench, water tank, excellent condition, drills daily, no tools or augers available  Price:  $120,000

CME 850 (Ref#9521Ne) Manufactured 1996, track mounted  Price:  $120,000

CME 850  (Ref#15543N)  Manufactured 1991, track mounted, Cummins diesel engine, auto hammer, angle hole capacity, Bean pump, in/out side to side slide base, 3 hoists, enclosed cab with heater, 33” tracks, quick disconnect mast, 3 leveling jacks, no auger.   Price:  $110,000  PRICE REDUCED:  $95,000

CME 850 (Ref#3007N) Manufactured 1990, track mounted, Cummins 4BT deck engine, 3 hoists plus wireline, (2) 140 gallon water tanks, angle capability, 3L8 Moyno pumps, in-out and side to side slide base, 140# auto hammer, 15000# front mounted hydraulic winch, breakout, 3 hydraulic leveling jacks, no tools or augers available  Price:  $80,000

CME 850 (Ref#219N) Manufactured 1989, track mounted with 4 cylinder Cummins diesel engine, auto hammer, angle capability, water tanks, 3L6 Moyno pump, in-out and side to side slide base, cathead, pipe racks, toolboxes, auger racks, 3 hydraulic leveling jacks, new tires, no tools or augers available  Price:  $85,000

CME 850  (Ref#979N)  Manufactured 1986, 6 cyl gas engine, track mounted, no air, Bean 425 pump, no tools or augers  Price:  $60,000  PRICE REDUCED:               $40,000

CME 850  (Ref#2557N)  Manufactured 1984, automatic CME SPT sampling hammer, 33” wide tracks with walking beam suspension, 3L8 Moyno pump, hydraulic power steering, powr shift transmission, 26’ mast, in/out hydraulic slide base, 3 leveling jacks, 15,000# winch, toolbox, auger and rod racks, angle hole capacity, updated 2005 with Isuzu diesel engine, 1800# and 7000# hydraulic winches, in/out and side to side slide base  Price:  $94,000  PRICE REDUCED:  $85,000

CME 850 (Ref#1946N) track mounted  Price:  $110,000

CME 750  (Ref#1050R)  Manufactured 1993, mounted on CME ATV, 140# auto hammer, no tools, cathead, 3 winches, diesel engine, 3L6 Moyno, side and front auger racks, hydraulic jacks, toolboxes, no slide base  Price:  $110,000

CME 750  (Ref#1299N)  300 gas 3L8 Moyno pump with transmission, mounted on Ardco buggy, hydraulic jacks, tool box, auger rack, 140# auto hammer, 3 winches, quick disconnect spinder, (20) 3-1/4 HS auger, (20) 2-1/4 HS auger (9) AWJ x 10’ drill rod, 3 AWJ x 5’ drill rod, 32x24 Lynac split spoon, 1 AW side feed swivel, hoist tools  Price:  $90,000

CME 550 ATV  (Ref#8386Na)  Manufactured 1979, mounted on ATV, with 300 6 cyl Ford gas engine, hydraulic cathead, L6 Moyno pump, no auto hammer, includes 1984 Brigadier lowboy with tractor and trailer  POR

CME 550X (Ref#4316N) Manufactured 2000, mounted on CME Buggy with Cummins diesel engine, hi torque right angle drive, in-out and side to side slide base, mainline winch, aux winch, wireline winch, Bean 435 pump, 150 gallon water tank, toolbox, rod rack, no auto hammer or breakout wrench 

Price:  $175,000  PRICE REDUCED:  $145,000

2000 Sterling tractor & Dynaweld trailer and some tools & augers avail at extra cost

CME 550X (Ref#8036R) Manufactured 2000, auto hammer, rod holder & breakout wrench, 3 winches, wireline, in-out & side to side slide base  Price:  $145,000

CME 550 (Ref#11011Na) Manufactured 1997, diesel engine mounted on ATV, 140# auto hammer, hydraulic rod holder, breakout wrench, in-out slide base, Moyno 3L8 pump, 2 winches with additional front winch, 250 gallon water tank, pipe rack, no tools or augers available  Price:  $165,000  PRICE REDUCED:  $105,000

CME 550X (Ref#8804Nb) Manufactured 1996, Cummins 300hp engine, mounted on ATV, 1300 hours, 7000# main hoist, 3200# aux hoist  Price:  $115,000

CME 550X (Ref#618Na)  Manufactured 1995, diesel on deck, truck mounted w/ diesel engine, Quick disconnect mast, 3L6 Moyno pump, 140# auto hammer, in/out slide base, front winch, 3 jacks, auger rack, rod rack, toolboxes  Price: $100,000

CME 550X (Ref#618Nb)  Manufactured 1994, diesel on deck, truck mounted w/ diesel engine, Quick disconnect mast, 3L8 Moyno, 140# auto hammer, in/out slide base, (3) jacks, front winch, auger racks, rod rack, toolbox  Price: $95,000

CME 550 (Ref#9434N) Mounted on 1994 Volvo Tractor with 6cyl Gas engine, cathead, auto hammer, Moyno L3 pump, in-out and side to side slide base, hydraulic breakout wrench, 3 hydraulic leveling jacks, tools available, good condition, well maintained  Price:  $115,000

CME 550  (Ref#2143N)  Manufactured 1990, mounted on ATV with 300 CID Ford gas engine, 140# auto hammer, 26’ mast with underside sheave, 8” cathead, 3 hyd hoists (7000#, 3200#, 1800#), hydraulic for wireline core drilling (less cable), spindle adaptor assembly, in/out slide base, (no Moyno pump), drop hammer rack, 4 hyd leveling jacks, good condition  Price:  $80,000

CME 550 (Ref#7044N) Manufactured 1988, mounted on rubber tracks with Deutz diesel engine, angle capability, QD mast, 2 hoists plus wireline, 140# auto hammer, Moyno 3L6 pump, (2) 75 gallon water tanks, in-out slide base, auger racks, toolboxes, 3 hydraulic leveling jacks, rod holder, breakout wrench, no tools or augers available  Price:  $75,000  PRICE REDUCED:  $65,000

CME 550 (Ref#9602N) Manufactured 1986, Ford industrial engine (1 year old) QD tower, auto hammer, 3L6 Moyno pump, rebuilt rotary box and transfer case  Price rig only:  $80,000

Also available mounted on 2003 Ford f650 flatbed with 20K Brooks Brothers trailer

Package price:  $100,000

CME 550  (Ref#2811Na)  mounted on ATV with Ford 6 cyl gas engine, cathead, 2 sandlines, in/out slide base, water pump, manual hammer, auger rack, toolbox, AW rods, 2-1/4”, 3-4.” And 4-1/4 augers, drill bits, extra set of rims with tires, excellent condition, currently drilling  Price $55,000

CME 55  (Ref#2811Nb)  parts rig.  4 cyl Ford Industrial gas deck engine, mounted on 1965 International 4-wheel drive (needs replacing), cathead, in/out slide base, 3 hyd leveling jacks  available at extra cost

PACKAGE PRICE FOR BOTH CME 550 AND CME 55:  $70,000

CME 550  (Ref#8212N)  refurbished 1990’s,  mounted on ATV 4 wheel drive  with John Deere diesel engine, 1 winch, auto hammer, quick disconnect mast, 3L6 Moyno pump, in/out slide base, 8000# winch, front pull out winch, toolboxes, auger and rod racks, no angle capability, good condition, currently drilling, no tools or augers, 260” long x 98” wide x 106” high – 14,000#   Price:  $90,000

CME 550 (Ref#9046N) Manufactured 1980, mounted on ATV with new 300 6 cylinder Ford engine, cathead, Moyno 3L8 pump, 2 winches, in-out slide base, water tank, no auto hammer, new gear box, rod racks, auger racks, 1 front 2 rear hydraulic leveling jacks, no tools or augers, good running condition, recently painted, new CME factory rotary box installed 6 months ago  Price:  $55,500  PRICE REDUCED:  $50,500

CME 550  (Ref#4097N)  Manufactured 1977, mounted on buggy carrier, 300 Ford 6 cylinder gas engine, 3L6 Moyno pump, no tools

2002 10-ton trailer

1987 Ford F800 diesel truck w/500 gal aluminum tank

Package Price:  $85,000

CME 550  (Ref#4258N)  Manufactured 1976, mounted on ATV with 300 gas engine, PTO, quick disconnect mast, in/out slide base, auto hammer, 3L8 Moyno pump, cathead, 100 gallon water tank, good condition  Price:  $70,000

CME 550 (Ref#15336N) Manufactured 1977, Ford 300 6 cylinder gas engine, mounted on ATV   Best offer

CME 450  (Ref#7810N)  late 1970’s model, buggymounted, gas engine, cathead, 2 winches, wter tank, in/out slide base, toolbox, auger rack, 4 hyd laveling jacks  Price on Request

CME 95  (Ref#6305N)  Manufactured 1988, deck engine: Cat 636 cu in 8 cylinder turbocharged liquid-cooled diesel engine rated at 250 hp (8,520 hours), mounted on 1993 Freightliner with 534,300 miles, Cat 3406B engine, Jake Brake, Fuller 9 speed transmission, includes trailer mounted Landa steam clearner power washer, includes (15) 8-1/4” inside diameter augers in 5’3” sections and adapters (79.5’ total), hydraulic system on rig has been reworked, transmission 4-speed forward, 4 speed reverse power shift tansmission with hydraulically actuated clutches and torque converter, 31,000 ft/lb max rotary torque  Price:  $250,000  OFF MARKET

CME 75 (Ref#8178Nb) Manufactured 2005, Cummins deck engine, mounted on 1993 Ford F9000 tandem axle truck (locking rears) with Cummins engine, cathead, in-out and side to side slide base, auto hammer, 3L6 Moyno pump, 500 gallon water tank, main hoist, 3200# aux hoist, wireline hoist, no breakout wrench, 3 hydraulic leveling jacks, hydraulic auger racks, some augers available  Price:  $170,000

CME 75 (Ref#1565N) Manufactured 2001, only 7300 hours, loaded, Cummins 5.9 turbo diesel deck engine, angle capability, mounted on 1994 International 8100 tandem axle truck with DT466 engine, Moyno 3l6 pump, 4 winches, auto hammer, cathead, water tank, hydraulic auger rack, breakout wrench, some tools  Price:    $200,000

CME 75 (Ref#3957Nb) Manufactured 2001, 5200 hours, Cummins 6 cylinder diesel deck engine, mounted on Peterbilt 300 with diesel engine, 250 gallon water tank, in-out & side to side slide base, 140# auto hammer, Moyno 3L8 pump, breakout table  Price:  $170,000

Tools & augers available at extra cost

CME 75 (Ref#6065N) Manufactured 2000, only 2850 hours, Cummins deck engine, quick disconnect mast and angle capability, mounted on 2000 International tandem axle truck, HT rotary box, large Kelly, Moyno 3L8 pump, 2 winches, hydraulic breakout holder & wrench, swivel, in-out slide base, 75 gallon fuel tank, 3 toolboxes, spares  Price:  $205,000

CME 75 (Ref#3957Na) Manufactured 2000, 7000 hours, Cummins 6 cylinder diesel deck engine, mounted on Freightliner FL80 with diesel engine, 250 gallon water tank, in-out & side to side slide base, 140# auto hammer, Moyno 3L8 pump, breakout table  Price:  $160,000

Tools & augers  available at extra cost

CME 75HT (High Torque) (Ref#6982N)  Manufactured 1994, mounted on 1994 GMC Topkick w/ 3116 Cat engine (new 2005), A/C, heater, 5 speed splitter, air brakes, runs excellent, 3 jacks.   Deutz deck engine air cooled with electronic idle, angle capability, quick disconnect, safety driver, 3 hydraulic winch lines (1) 8,000# and (2) 3,000#, Mobile safety driver wireline with 140 lb down the hole hammer. Side to side and front to back wiggle tail, 250 gallon water tank, Moyno 3L8 pump, auger racks, toolboxes, safety shut off switches.  One owner rig.  Price: $100,000

Available at extra cost: 

50’ of 6-1/4” auger,

2004 steam cleaner with decond trailer unit with self contained decon catch basin mounted on tandem axle trailer.

Grout whirlybird mixers, cookie cutters, samplers and excesswell materials.

CME 75  (Ref#1042N)  Manufactured 1994, High torque,  Cummins 5.9 on deck, 5905 hours, mounted on 1994 Ford Ford F800 (not 4x4) with Cummins 6BT engine, 140# auto hammer, cathead, 3L8 Moyno pump, 3 hoists, wireline winch, in/out and side to side slide base, breakout table, hydraulic chuck, water tank, toolboxes, auger racks, excellent condition  Price:  $115,000   Tools and augers available at extra cost.

CME 75 (Ref#6436N) Manufactured 1994, Cummins 4 cyl deck engine, 250 gallon water tank, in/out slide base (no side to side), 30,000# front winch, mounted on 1999 Marooka 1500 with Mitsubishi diesel engine, 3 hydraulic leveling jacks, rebuilt 3L8 Moyno pump, auto hammer, rod holder/breakout, wireline & 2 winches, water tank, auger rack  Price:  $105,000  OFF MARKET

CME 75  (Ref#6817N)  Manufactured 1994, 6BT Cummins deck engine, cathead, 3 hoists: 1800, 3200, and 8500, 250 gal water tank, side to side slide base, 25’ mast with breakaway, 6’ stroke, Moyno 2L8 pump, Bowie pump, angle drilling capability, mounted on 1994 F800 single axle with Cummins engine, 10 speed, auto hammer, rod holder with breakout wrench, hyd auger rack, air compressor for impact tools, 3 hydraulic leveling jacks, no tools or augers  Price:  $130,000       OFF MARKET

CME 75 (Ref#9772R) Manufactured 1993, high torque, Deutz diesel deck engine, mounted on 1998 International with DT466 engine, 10 speed transmission, 3 winches plus wireline, Moyno 3L6 pump, auto hammer, breakout wrench, in-out and side to side slide base, 120’ NWJ rods, 120’ of 8” augers, samplers, hand tools  Price:  $110,000

CME 75  (Ref#1117N)  Manufactured 1993, diesel engine, high torque, mounted on 1993 International 4900 truck, 3L8 Moyno pump with 3 speed gearbox, 8500#/3500# winches, 250 gallon water tank, toolboxes, hydraulic breakout wrench   Price:  $110,000

CME 75 (Ref#9031N) diesel deck engine, less than 3000 hours, mounted on 1992 Ford F800 (not 4x4) with gas engine, in/out and side to side slide base , auto hammer, no cathead, 3 hoists, water tank, rod holder, no breakout wrench, augers & tools included  Price:  $85,000

CME 75 (Ref#2381N) Manufactured 1992, Cummins deck engine, mounted on 1992 GMC 6 x 4 with Cat 3116 engine, 10 speed Fuller transmission, high torque rotary drive, angle drilling, cathead, 8500# hoist, (2) 1800# hoists, wireline hoist, wireline hammer winch, in-out and side to side slide base, Moyno 3L8 pump, rod holder & breakout wrench, 140# auto hammer, 500 gallon water tank, 1 front 2 rear hydraulic leveling jacks, rod rack, hydraulic auger rack, toolboxes, hydraulic air compressor, one owner rig, excellent condition  Price:  $145,000  OFF MARKET

CME 75  (Ref#1428N)  Manufactured 1991, Ford 6 cylinder pony motor, 360 gallon deck mount water tank, CL-10 Continental pump 3” suction, 3-speed pump trans., 3 winches 1800#, 3400# ad 10,000#, slide base, rod chuck breakout wrench, cathead with hammer, on deck rod racks, front munt auger rack, on deck tool box, mounted on 2006 MST 1500 VD Marooka carrier (200 hours), rig has done over 200’ 5” piston sampling  Price:  $165,000

CME 75 (Ref#6275N) Manufactured 1990, brand new Deutz diesel deck engine, mounted on 1990 Ford 800 4x4 with diesel engine, angle drilling, safety driver, auto hammer, Moyno 3L8 pump, in-out and side to side slide base, 3 winches, 250 gallon water tank, 3 hydraulic leveling jacks, one owner rig, well maintained, no tools or augers  Price:  $90,000

CME 75 (Ref#8178Na) Manufactured 1990, Cummins deck engine, mounted on 1994 Ford F9000 tandem axle truck (locking rears) with Cummins engine, cathead, in-out and side to side slide base, auto hammer, 3L6 Moyno pump, 500 gallon water tank, main hoist, 3200# aux hoist, wireline hoist, no breakout wrench, 3 hydraulic leveling jacks, hydraulic auger racks, some augers available  Price:  $65,000

CME 75 (Ref#144N)  Manufactured 1989, 2L8 Moyno pump, Gas on deck, in/out and side to side slide base, cathead, 250 gal water tank, Quick disconnect mast, auger racks, rod racks, toolbox, mounted on truck w/ diesel engine  Price: $90,000

CME 75  (Ref#5699N)  Manufactured 1987, mounted on F800 truck with diesel engine, diesel on deck, 3 winches plus wireline, 3L8 pump, auto hammer, rod holder/breakout wrench, in/out side to side,  Price:  $110,000

CME 75  (Ref#431N)  Manufactured 1986, Deutz diesel deck engine, 3L6 Moyno pump, cathead, in/out and side to side slide base, Joy developmental air compressor, 3” Wilden pump, 3 hoists, hydraulic rod holder, breakout wrench, auger rack, toolboxes, mounted on 1997 International 4-wheel drive with DT466 engine, some tools and augers, excellent condition, currently drilling  Price:  $150,000  PRICE REDUCED:  $95,000

CME 75  (Ref#3534N)  Manufactured 1985, mounted on 1989 GMC truck, 6 cyl Ford Industrial deck engine, 4-1/2 x 5 Gardner Denver mud pump, breakout wrench, cathead, 30 ton Pullmaster winch, in/out slide/side slide base, differential lock on rear, good running condition, no tools  Price:  $95,000

CME 75  (Ref#1310N)  Manufactured 1985, Deutz diesel deck engine, mounted on Franklin articulating buggy with Detroit diesel engine, cathead, in/out slide base, front winch on buggy, 2 winches on rig, 3 hyd jacks, toolbox, auger racks  Price:  $65,000  (tooling and augers available)

CME 75  (Ref#15285)  Manufactured 1985, mounted on 1984 Ford tandem axle truck powered by 8.2 ltr V8 Detroit diesel engine, Ford 6.2 ltr diesel engine on deck, 3L8 Moyno pump, water tank, 2 winches, wiggle tail, table in and out, auger racks, cathead   Price:  $75,000    Off Market

Extra equipment at extra cost:  100’ of 4-1/4” auger, 100’ of JW rod, (2) drive caps, (2) cutter head, auto hammer

CME 75 (Ref#2692N) Manufactured 1983, mounted on 1979 Ford F800 with Cat engine, Ford 380 deck engine, , in-out and side to side slide base, cathead, grout pump, automatic slide out auger racks, 3 winches, toolboxes, pipe racks, 1 front 2 rear hydraulic leveling jacks, no water tank, no auto hammer  Price:  $85,000  PRICE REDUCED:  $50,000

CME 75  (Ref#3507N)  Manufactured 1982, 6500 hours, diesel deck engine, mounted on 1992 International 4900 6x4 truck with DT466 engine, cathead, injection pump, 3 winches, in/out and side to side slide base, no angle capabilities, breakout wrench, toolbox, rod rack, auger rack, 400 gallon water tank, 3 hyd leveling jacks  Price:  42,000

No tools or augers

CME 75  (Ref#4259N)  Manufactured 1979, 300 gas deck engine, mounted on 1983 International truck with diesel engine, 3L8 Moyno pump, cathead, 250 gal water tank, in/out and side to side slide base, breakout wrench, good condition  Price:  $70,000

CME 75  (Ref#8286b)  Manufactured 1979, mounted on International single axle truck with diesel engine, gasoline engine on deck, 3 leveling jacks, cathead, slides in/out, 3L6 Moyno pump  Price:  $50,000

CME 75  (Ref#315N)  Manufacutured 1977, Ford 300 deck engine, mounted on 1989 International 2375 with Cummins L10, in/out and side to side slide base, winch, hydraulic auger rack, good condition  Price:  $50,000

CME 75  (Ref#2753N)  Manufactured 1976, rebuilt 300 6 cylinder gas deck engine, not mounted, cathead, in/out and side to side slide base, well maintained, no tools or augers  Price:  $60,000

CME 75  (Ref#440N)  Manufactured 1975, mounted on 1989 Marooka MSTY800 rubber track carrier with Mitsubishi diesel engine, 3 hydraulic leveling jacks, toolbox, 325 gallon plastic water tank, rod and auger racks, 2 winches, in/out slide base, Ford gas deck engine, Moyno 3L6 pump, hydraulic auto hammer.  Cylinders, motors, valves and the pump rebuilt 2008 with CME parts.  All hydraulic hoses replaced with Parker hydraulic hoses.

 (All tooling is CME unless otherwise noted)

1              1 5/8” hex lifting cap

1              1 5/8” hex drive cap for 4 1/4” hollow stem auger

1              5' lead 4 1/4” I.D. hollow stem auger

19           5' standard 4 1/4” I.D. hollow stem auger

1              4 1/4” I.D. hollow stem auger holder

1              4 1/4” I.D. finger cutter head

12           Spare finger bits

1              4 1/4” I.D. conical cutter head

1              Conical bit removal tool

12           Spare conical bit

5              4 1/4” plastic plugs

1              NWJ drive cap adapter

1              NWJ center bit adapter

1              Fish tail center bit

20           5' NWJ rod

1              2’ NWJ rod

1              1’ NWJ rod

1              NWJ hoisting plug

1              NWJ closed holding iron

1              NWJ closed slip ring

6              2" x 24" Lynac split barrel samplers

2              2 1/2” x 18” Californian modified samplers (not CME)

1              Continuous sampler

1              NWJ box to AWJ pin adapter

1              20’ 1” hose with female cam lock fitting (not CME)

2              10’ 2” hose with male and female cam lock fitting (not CME)

Price:  $180,000

CME 75  (Ref#5284N)  Manufactured 1973, mounted on 1984 Ford 700 4x4 truck with gas engine, 300 cubic gas on deck, cathead, 25’ mast, in/out side to side slide base, new 480 gallon water tank, 3L6 Moyno, 20,000# winch, 48,000 miles, 3 jacks, no auto hammer  Price:   $45,000

CME 75  (Ref#5007N)  Manufactured 1972, diesel deck engine, mounted on 1975 Mack truck with diesel engine, cathead, no auto hammer, breakout cylinder, 3 winches and wireline winch, injection pump, in/out and side to side slide base, auger racks, toolboxes, 1 front and 2 rear hyd leveling jacks, no tools or augers, good condition  Price:  $52,000  PRICE REDUCED:  $37,000

CME 55 (Ref#8382N) Ford 6 cylinder 300 gas deck engine, mounted on 1993 International 4900 with DT 466 diesel engine, high torque drive, 8” cathead, 5000# capacity, in-out & side to side hydraulic slide base, Moyno 3L8 pump, 475 gallon stainless steel water tank, 1800# & 7000# winches  Price:  $82,000

CME 55  (Ref#3240Nc)  Manufactured 2004, mounted on 1500 Morooka Carrier, Carrier Winch 20,000 lbs, In/Out Slide Base, 3L10 Moyno Pump, Top Feed Swivel with Plumbing, Main Winch 8000 lbs, Secondary Winch 3200 lbs, Wireline Winch, 350 Gallon Aluminum Water tank, Auger Racks, Front and Rear Swing Out, Three 36” Tool Boxes, Enclosed Rod Rack, Three Leveling Jacks  Price:  $195,000 OFF MARKET

CME 55 (Ref#3957Nd) Manufactured 2003, 7100 hours, Cummins 4 cylinder diesel deck engine, mounted on 300 rubber track carrier, 18” tracks, Moyno 3L8 pump, 140# auto hammer, in-out & side to side slide base, breakout table  Price:  $170,000

Tools, augers & trailer available at extra cost

CME 55 (Ref#3957Nc) Manufactured 2001, 8800 hours, Cummins 4 cylinder diesel deck engine, mounted on 300 rubber track carrier, Moyno 3L8 pump, 140# auto hammer, in-out & side to side slide base, breakout table  Price:  $145,000

Tools, augers & trailer available at extra cost

CME 55 (Ref#3240Nd)  Manufactured 2000, Mounted on 300 Carrier , Carrier Winch, In/Out Slide base, 3L6 Moyno Pump, 4BT Cummins engine, 140# autohammer, no cathead, in/out and side to side slide base, Top Feed Swivel with Plumbing, Winch 3200 lbs, Winch 3200 lbs, Wireline Winch, Auger Racks, Front and Rear Swing Out, Four Tool Boxes, Three 24” and One 48”, Exposed Rod Rack, Four Leveling Jacks   Price:  $160,000 – OFF MARKET

CME 55HT  (Ref#4506N)  Manufactured 1997, 4BT Cummins diesel on deck, 26’ quick disconnect mast, water tank, toolbox, 2 hoists, hyd auger racks, mounted on 1998 Ford F800 4x4 truck with diesel engine  Price:  $90,000  OFF MARKET

CME 55  (Ref#107N)  Manufactured 1990, gas deck engine, mounted on Ford F700 4x2 truck (not 4x4) with Ford 6 cyl gas engine, 3 jacks, 250 gal water tank, cathead, in/out and side to side slide base, 22’ quick disconnect mast, no angle cap., 140# SPT hammer, 3 hoits, Moyno 3L6 pump, auger racks, rod rack, toolbox, currently drilling  Price:  $60,000

CME 55  (Ref#3041N)  Manufactured 1988, Ford 6 cyl Industrial heavy duty deck engine, cathead, Moyno pump, mounted on 1988 Ford all wheel drive truck, 150’ auger, 3 leveling jacks, good runnig condition  Price:  $55,000

CME 55  (Ref#6926N)  Manufactured 1988, in out/side to side slide base, 3L8 Moyno pump, auto hammer, cathead, main winch (8500#), aux winch 3200#), mounted on Ford L800 truck with diesel engine, Cummins 4 cyl diesel deck engine  Price:  $85,000  OFF MARKET

CME 55  (Ref#6807N)  Mounted on 1988 Ardco 4 wheel drive buggy with diesel engine, 2 winches, gasoline engine on deck, auto hammer, cathead, 3L Moyno pump  Price:  $95,000

CME 55  (Ref#1600Nb)  Manufactured 1987, 6 cyl Ford gas deck engine, mounted on 1989 Ford (not 4 x 4) with 429 gas engine, cathead, safety driver, no auto hammer, in/out slide base, 1 sandline, 300 gallon water tank, Moyno 3L6 pump, underbody toolboxes, auger and pipe racks, 2 rear hydraulic leveling jacks, good condition, currently drilling  Price:  $60,000  PRICE REDUCED:  $50,000

Tools and augers available at additional cost.

CME 55  (Ref#6175N)  Manufactured 1987, Ford 300 6 cyl Industrial gas deck engine, mounted on 1989 Ford F700  (not 4x4) single axle truck with Cat diesel engine, cathead, 1800# and 3200# winches, 3L6 Moyno pump, 140# auto hammer, in/out and side to side slide base, 350 gallon water tank, 3 hyd leveling jacks, no tools or augers, good condition, currently drilling  Price:  $75,000  OFF MARKET

CME 55  (Ref#4793Nb)  Manufactured 1987, Ford gas deck engine, mounted on International (not 4x4) truck with DT466 engine, cathead, in/out slide base, 3 hydraulic leveling jacks, 100’ of 6” HAS, good condition  Price:  $75,000

CME 55  (Ref#12604N)  300 Ford Industrial gas deck engine, mounted on 1986 Ford F700 (not 4x4) with gas engine, 30’ mast, in/out and side to side slide base, cathead, 2 hoisting winches, 140# hammer, 170# TX DOT hammer, 2” swivel, 3L6 Moyno pump, toolbox, auger racks, 50’ of 5’ and 100’ of 10’ NWJ rods, 75’ straight flight 4-1/2” augers, fully tooled, ready to go, 3 hyd leveling jacks  Price:  $80,000

CME 55  (Ref#15151)  Manufactured 1985, new 6 cylinder Ford Industrial engine on deck, mounted on Ford F700 truck with Ford 370 gas engine, augers, casing, wireline, tools  Off market

CME 55  (Ref#5198N)  Manufactured 1983, 6 cyl gas engine, mounted on 1985 Gemco 4 x 4 buggy, 3L6 Mayho with Detroit diesel engine, (2) winches, cathead, new brass throughout, auger racks, rod racks, core barrel storage, tool boxes, front winch

1996 CH612 MACK SEMI, single axle, air ride cab and suspension, new brakes

2006 25-ton Kaufman lowboy

PACKAGE PRICE:  $65,000

CME 55  (Ref#3611N)  Manufactured 1983, mounted on 1989 International truck with diesel engine, Ford Industrial gas engine on deck, no auto hammer, no breakout wrench, cathead, Moyno pump, water injection, 3 hoists, 1 front and 2 rear leveling jacks, water tank, bare rig, no tools or augers  Price:  $70,000  PRICE REDUCED:  $55,000

CME 55  (Ref#4545N)  Manufactured 1982, 6 cyl Ford on deck, 22’ Quick disconnect mast, 3L6 Moyno pump, water tank, mounted on 2002 F750 Super Duty 4x4 truck with diesel engine, (3) 36” jacks  Price:  $53,000  OFF MARKET

CME 55  (Ref#419Na)  Manufactured 1981, 300 Ford gas deck engine, mounted on Ardco buggy w/353 Detroit engine, cathead, auto hammer, 3L6 Moyno pump, 150 gallon water tank, in/out and side to side slide base, (3) 36” hydraulic leveling jacks  Price:  $90,000  OFF MARKET

Tools and augers available at additional cost.

CME 55 (Ref#3301Nb) Manufactured 1981, gas deck engine, mounted on 1998 Ford F700 (not 4x4) with gas engine, cathead, in-out slide base, QD mast, angle capability, 2 winches, Moyno 3L6 pump,  300 gallon water tank, auger racks, toolbox, 2 rear hydraulic leveling jacks   Price:  $49,500

CME 55  (Ref#13902)  Manufactured 1981, 6 cyl Ford gas engine, mounted on 1964 International Fleetstar 2000 tandem axle Road tractor with Cummins diesel engine, 10 speed Road Ranger transmission, 2 hydraulic wireline winches (7,000# and 3200#), needs new clutch, in/out wiggle tail base, 26’ mast, cathead, 500 gal water tank, 3L6 Moyno pump, King 1J water swivel, 140# safety hammer, hydraulic breakout pipe wrenches, cathead 

Price:  $37,500

Augers available at extra cost

CME 55  (Ref#15037)  Manufactured 1981, mounted on 1990 International truck with diesel engine, Ford Industrial gas engine on deck, Bean 35 mud pump, 30,000 miles, no tools  Price:  $45,000

CME 55  (Ref#5215N)  Manufactured 1979, 6 cyl  Ford Industrial deck engine (rebuilt), 3L8 Moyno pump, right angle drive, cathead assembly, 2 rear leveling jacks, no auger, rig has been sitting about a year;  can have it in good running condition  Price:  $60,000

CME 55  (Ref#5939)  Manufactured 1979, 3L6 Moyno, mounted on 1996 single axle GMC truck w/Cat diesel engine, auto hammer, wiggle tail, slide base, 3 jacks, water tank, rod rack, cathead, tool boxes, (2) winches   Price:  $65,000

CME 55 (Ref#4300N) Manufactured 1978, rebuilt by CME 2002,  300 Ford 6 cylinder deck engine, mounted  on 2002 GMC 6500 with Cat engine, 30’ mast, no angle capability, 1 winch, hydraulic cathead, in-out slide base, 250 gallon water tank, no pump but connections are there, auger racks, toolboxes, 140# auto hammers, augers, AWJ rods  Price:  $70,000

CME 55  (Ref#1056N)  Manufactured 1977, diesel deck engine, mounted on 1989 Ford 700 (not 4x4) truck with diesel engine, set up for auger and coring, cathead, sandline, in/out slide base, Moyno 3L6 pump, breakout wrench, no auto hammer, no tools available, 3 hyd leveling jacks, good condition  Price:  $110,000

CME 55 (Ref#4106N) Manufactured 1977, gas deck engine, mounted on 2006 GMC 6500 with diesel engine, in-out slide base, cathead, breakaway tower, Bean pump, no angle capability, 2 winches, some tools & AWJ 5’ rods  Price:  $75,000

CME 55  (Ref#15227)  Manufactured 1976, mounted on 1986 International truck with DT466 engine, 4 cyl Ford diesel deck engine, 140# automatic SBT hammer, 7000# hydraulic hoist, hydraulic in/out slide base, Moyno 3L6 water pump, 250 gallon water tank, 2 rear hydraulic leveling jacks  Price:  $50,000  OFF MARKET

CME 55 (Ref#3923Nd) Manufactured 1975, mounted on 1970 Bombadier MS70 track, Moyno 3L6 pump, CME auto hammer, 500 gallon water tank, 3 split spoons, NX core barrel, 95’ of AW rods, 35’ of 4 ¼” HSA, 2 cutting heads, 1999 Sterling L7501 and a Holden CZ trailer  Price:  $93,000  PRICE REDUCED:  $75,000

CME 55  (Ref#15036)   Manufactured 1974, mounted on 1985 Ford F700 truck with gas engine, 50,000 miles, Ford Industrial gas engine, Bean 35 mud pump, no tools  Price:  $33,000

CME 55  (Ref#14695)  Manufactured 1974, good condition, mounted on 2000 F650 heavy duty King cab with Cat diesel engine,  32,000 miles, like new, rig frame has been shortened with new framing and toolboxes   Price:  $65,000

CME 55 (Ref#3923Nc) Manufactured 1973, Ford 300 industrial gas deck engine, mounted on John Deere wood skidder with 4 cylinder diesel engine, Moyno 3L6 pump, cathead and safety hammer, 1 winch, auger racks  Price:  $25,000 

CME 55 (Ref#2485N) Manufactured 1973, high torque, mounted on 1983 International all wheel drive, no cathead, auto hammer, in-out and side to side slide base, Moyno 3L6 pump, 25’ mast, 3 winches, 1 front & 2 rear hydraulic leveling jacks, auger rack, toolbox, augers etc.  Price:  $60,000  PRICE REDUCED:  $50,000

CME 55  (Ref#886N)  Manufactured 1973, 6 cyl Ford gas engine, completely rebuilt 2 years (1 job since rebuilt), mounted on 1980 single axle Ford LN8000 truck with 3208 Cat diesel engine, cathead, 2 winches, 3 jacks, 50’ of 6” augers, split spoon, 5’ and 10’ rods, new 5/16” cable  Price:  $55,000  OFF MARKET

CME 55  (Ref#15056)  Manufactured 1973, mounted on 1990 Kodiak single axle truck with new 366 gas engine, new 300 6 cyl gas deck motor, 2 winches, 2 jacks, new Moyno 3L6 pump, bare rig  Price:  $60,000

CME 55  (Ref#14410)  Manufactured 1973, track mounted  Price:  $40,000

CME 55  (Ref#14398)  Manufactured 1973, 6 cyl 300 gas deck engine, mounted on 1974 Ford 700 truck w/gas engine, cathead, water injection, 3 leveling jacks  Price:  $40,000

CME 55 (Ref#11881N)  Manufactured 1968, mounted on 1976 International single axle 4 wd truck with 392 International gas engine (rebuilt truck engine) but not currently running, Ford 4 cylinder gas engine, new mechanical winch, 2 jacks, 3L6 Moyno pump  Price:  $19,500

CME 55 (Ref#4709R) Manufactured 1966, gas deck engine, mounted on 1981 Ford F370 (not4x4) with gas engine, in-out and side to side slide base, cathead, no auto hammer, 250 gallon water tank, no Moyno pump, 2 winches, toolbox, auger rack, 1 front & 2 rear hydraulic leveling jacks, split spoon samplers, barrels, tools, augers, etc  Price:  $40,000

CME 55  (Ref#8286a)  mounted on single axle Chevy truck with gasoline engine, 3L6 Moyno pump, 3 leveling jacks, gasoline engine on deck  Price:  $55,000

CME 55  (Ref#8477)  Ford 6 cylinder 300 CID engine on deck (rebuilt), in-out, side to side base, 3 jacks, 1 winch, cathead, 26’ mast, Moyno 3L6, 250 gal water tank, auger rack tool boxes, mounted on 1996 International single axle truck with DT466 engine, front winch, good tires, good condition, ready to work  Off Market 11/04

CME 45C (Ref#6700N) Manufactured 2009, low hours, mounted on 4x4 Dodge 5500 truck, in/out side to side slibe base, 3 hoists, Moyno 3L6 pump, auto hammer, wiggle tail, auger racks, toolboxes, excellent condition, 140# auto hammer, 100 gal water tank, 40’ of 3-1/2” hollow stem augers  Price:  $180,000  OFF MARKET

CME 45C (Ref#3863R) Manufactured 2000, mounted on Morooka MST 600, auto hammer, 2 hoists, 3 leveling jacks, good condition  Price:  $70,000

CME 300/45C (Ref#4164N) Manufactured 2008, diesel engine, tracks in “like new” condition, less than 600 hours, in-out & side to side slide base, 140# auto hammer, cathead, Moyno 3L6 pump, 15’ mast, angle capability, 1800# winch, rod rack, toolboxes, auger rack  Price:  $165,000

CME 45C  (Ref#3604N)  Manufactured 1996, 3 cylinder Deutz diesel engine, 3L6 Moyno pump, wireline, 2 main winches 3200#, 8,000# electric winch in front, 140# auto hammer, mounted on skid  Price:  $60.000

CME 45C  (Ref#2134N)  Manufactured 1995, 3 cyl Deutz diesel on deck, mounted on Marooka MST 800 rubber tracks, 140# auto hammer, no cathead, 2 winches, in/out side to side slide base, Moyno 2L6 pump, auger racks, (3) 36” jacks

1989 PETERBILT ROLL BACK CARRIER, rebuilt Cummins 350 diesel engine

Package Price:  $110,000  OFF MARKET

CME 45B (Ref#6100R) Manufactured 1992, gas deck engine, mounted on 1992 Ford 4x4 superduty with diesel engine, auto hammer, in-out slide base, 1 winch, auger & rod racks, toolboxes, 3 hydraulic leveling jacks  Price:  $50,000

CME 45B (Ref#388Na) Manufactured 1989, Ford industrial gas engine, mounted on 2003 Ford F550 (not 4x4) with diesel engine, cathead, no auto hammer, Moyno pump, 2 hoists, no water tank, in-out slide base, 1 front & 2 rear hydraulic leveling jacks  Price:  $65,000

CME 45B  (Ref#6567N)  Manufactured 1988, mounted on Gemco 150 buggy with gas engine, gas deck engine, 3L Moyno pump, in/out slide base, 1 winch, cathead, auto hammer, 2 rear hyd leveling jacks, no tools  Price:  $70,000

CME 45B (Ref#3872Nc) mounted on Marooka MST 600   Price:  $75,000

CME 45  (Ref#1600Na)  Manufactured 1987, 4 cyl White gas deck engine, mounted on 1992 Ford 4 x 4 with 10 cyl gas engine, auto hammer, 2 sandlines, in/out slide base, no cathead, 2 underbody toolboxes, auger and pipe racks, 2 rear hyd leveling jacks, good condition, currently drilling  Price:  $55,000  OFF MARKET

Tools and augers available at additional cost.

CME 45B  (Ref#3637N)  Manufactured 1987, gas deck engine, mounted on 1987 Ford F700 truck with gas engine, no cathead, 140# auto hammer, 2 winches, 3L6 Moyno pump, in/out and side to side slide base, 250 gal water tank, 3 hydraulic leveling jacks, no tools or augers, drills daily  Price:  $55,000 – OFF MARKET

CME 45B  (Ref#419Nb)  Manufactured 1986, White industrial gas deck engine, mounted on 1986 International 4 x 4 truck with diesel engine, no cathead, auto hammer, 3L6 Moyno pump, 150 gallon wtertank, SK58 probe hammer, in/out and side to side slide base, 3 hyd leveling jacks,  Price:  $80,000  OFF MARKET

Tools and augers available at additional cost.

CME 45C (Ref#4704Na) Manufactured late 1970’s, Wisconsin gas deck engine, mounted on rubber tack carrier, mainline winch, Moyno 2L6, 18’ derrick, slide base, cathead, tracks expandable up to 44”, well maintained & ready to go  Price:  $67,500

Trailer available at extra cost

CME 45B (Ref#2428N) Manufactured 1979, completely refurbished, new 4 cylinder Wisconsin gas deck engine, mounted on 1992 Ford 700 (not 4x4) with diesel engine, cathead, in-out slide base, 3L6 Moyno pump, 300 gallon water tank, no auto hammer, 2 toolboxes, rod racks, 2 rear hydraulic leveling jacks  Price:  $42,500 -     Tools & augers avail at extra cost

CME 45B  (Ref#13855)  Manufactured 1978, mounted on 1979 International truck w/gas engine, rig powered by 4 cyl Ford Industrial gas engine, cathead, slide base, winch, 1 front and 2 rear hydraulic leveling jacks, manual hammer, 120’ of 4” augers, 30’ of 6” augers, all tools (split spoons, 5’ and 10’ rods, drive heads, good condition, not used in 4 years (covered outside) Price:  $35,000

CME 45  (Ref#1448N)  Manufactured 1976, Ford 4 cylinder pony motor, 300 gallon deck mount water tank, CL6 Continental pump, Pull Master PL-1  1,100# winch, Pull Master PL-2  2,200# winch, Cathead w/ hammer, Slide base, Rod Chuck, On deck tool box, On deck rod racks, Front mounted auger racks, Extended mast 20” pull, Front Jack, mounted on 1992 800MST Marooka rubber track carrier, Low hrs.  Price:  $62,000

CME 45B  (Ref#6568N)  Manufactured 1974, mounted on Gemco 150 buggy with 300 gas engine, PTO, cathead, 1 winch, in/out slide base, 3L6 Moyno pump, 2 rear hyd leveling jacks, no auto hammer, no tools  Price:  $55,000  PRICE REDUCED:  $40,000

CME 45B  (Ref#1846N)  Manufactured 1973, Ford 4 cyl gas pony motor with 398 hours on rebuilt motor, 100 gal deck mounted water tank, mounted on 1990 Ford F700 truck with 429 4V gas engine, 5 speed single rear axle transmission, cathead, 140# hammer, Koenig winch, 2 rear jacks, 2 toolboxes, tooling, 60’ of 4” x 5’ long auger, 10’ of 6” dia auger, 60’ of 5’ AW rod     Price:  $38,500

CME 45B (Ref#2412Ne) Manufactured 1968, 4 cylinder diesel deck engine, mounted on articulating ATV with rebuilt engine, front winch  Price:  $35,000

CME 45 (Ref#6710Na) Ford 4 cylinder industrial gas deck engine, mounted on 1982 Ford F700 with diesel engine, not 4x4, in-out slide base, cathead, Moyno 3L4 pump, set up for wireline, coring & augering, some hollow stem augers & NQ rods available  Price:  $18,000

Also available as a package with the following:

CME 45 (Ref#6710Nb) Ford 4 cylinder industrial gas deck engine, mounted on 1992 Dodge 1 ton with 360 gas engine, in-out slide base, cathead, Moyno 3L4 pump, set up for wireline, coring & augering, some hollow stem augers & NQ rods available

SOILTEST HYDRO AUGER DRILL (Ref#6710Nc) Ford 4 cylinder industrial gas deck engine, mounted on 1993 Chevy 1 ton with 350 gas engine, in-out slide base, all hydraulic for soil sampling

Package price:  $55,000

CME 45C  (Ref#13468)  trailer mounted, Wisconsin engine, cathead, winch, 2L6 Moyno pump, water tank, tools, good condition, currently drilling  Off Market

DIEDRICH D-120 (Ref#6597N) Manufactured 1996, John Deere 6 cylinder diesel deck engine, mounted on 1995 Freightliner with Detroit 12.7 liter engine, flotation tires in front, in-out and side to side slide base, breakout table, breakout wrench, 500 gallon water tank, 140# SPT hammer, cathead, (2) 3000# winches, 10000# winch, set up for mud, rotary or augers, 2 swing out auger racks, 4 leveling jacks  Price:  $175,000 – OFF MARKET

DIEDRICH D-120 (Ref#4890Na) rebuilt John Deere deck engine, mounted on 1996 Freightliner FLD120 with Cummins N14 engine, rebuilt Moyno 3L8 pump, 500 gallon water tank, cathead, fluted kelly  Price:  $145,000

DIEDRICH D-120 (Ref#6583Na) Manufactured 1995, less than 1300 hours, John Deere diesel engine, just rebuilt, 4 winches, breakout table & wrench, 12000 ft/lbs torque,5’ stroke, rope cathead, Bean 435 piston pump, mounted on 1979 Mack Econodyne with diesel engine   Price:  $105,000

auto hammer available at additional cost

DIEDRICH D-120  (Ref#3462Na)  John Deere 6 cyl diesel engine, Moyno 3L8 pump, 10,000# main winch, 5,000# secondary winch, wireline winch 800 lbs., cathead, auto hammer, overhead water swivel  Price:  $140,000

DIEDRICH D-120 (Ref#5287N)  Manufactured 1994, John Deere diesel engine, mounted on 1994 Ford F800 with diesel engine (not 4x4), in-out and side to side slide base, cathead, 500 gallon water tank, auto hammer, Moyno 3L8 pump, auger racks, toolboxes, 3 hydraulic leveling jacks, 10000# & 2000# hoists, no tools or augers available  Price:  $76,000

DIEDRICH D-120  (Ref#6686N)  Manufactured 1994, cathead, safety driver, 3L8 Moyno pump, 10,000# and 3,500# winches, 500 gallon water tank, 2 speed top head, double auger racks, toolboxes, in/out and side to side slide base, 6’ stroke, mounted on 1994 GMC Topkick with diesel engine, no tools or augers, 140/300# auto hammer, no breakout wrench, good condition, currently drilling  Price:  $170,000  PRICE REDUCED:  $110,000

DIEDRICH D50 (Ref#11011Nb) Manufactured 2009, only 450 hours, turbo track rig, John Deere diesel engine, remote control rig, 140# auto hammer, hydraulic rod holder, breakout wrench, in-out and side to side slide base, Moyno 3L8 pump, 2 winches, wireline, additional front winch, QD mast, pipe rack, no tools or augers available  Price:  $245,000

DIEDRICH D50  (Ref#5046N)  Manufactured 2004, mounted on 4 wheel drive with International diesel engine, auto hammer, quick disconnect mast, flotation tires  Price:  $140,000  OFF MARKET

DIEDRICH D50  (Ref#5312N)   Manufactured 1999, Duetz diesel engine on deck, mounted on Ford F550 4x4 truck with 7.3 diesel engine, 2 wiches, cathead, 3500 hrs, 68,800 miles, 3L6 Moyno pump, new water tank, (2) tool boxes, 2 rear jacks  Price:  $70,000

DIEDRICH D50 (Ref#14979N) Manufactured 1993, diesel deck engine, Mounted on Marooka carrier with diesel engine, running now but needs some refurbishing, no tools available  Price:  $35,000

DIEDRICH D-50 (Ref#2412Nd) Manufactured 1989, 4 cylinder Deutz diesel deck engine, low hours, mounted on articulating ATV with 4 cylinder Ford engine, auto hammer  Price:  $35,000

DIEDRICH D-50 (Ref#6583Nf) Manufactured 1988, Deutz diesel deck engine, mounted on Kubota RG-60 tracks with 5 cylinder Kubota engine, (2) 3000# winches, breakout wrench, right angle drive, cathead, Bean 40 pump, 200 gallon water tank, toolboxes, 5’ stroke   Price:  $120,000

DIEDRICH D-50  (Ref#1511N)  Manufactured 1988, mounted on 1976 Bombadier track, John Deere diesel engine on rig, Perkins diesel on Bombadier, Bean pump  Price:  $70,000

DIEDRICH D50  (Ref#5218N)  Manufactured 1988, 4 cy gas on deck, slide base, cathead, 6000# main winch, 3200# aux winch, 3L6 Moyno pump, auger racks, toolboxes, mounted on Ford F700 single axle truck with Ford gas engine, no hammer, no tools, no augers  Price:  $30,000

DIEDRICH D-50  (Ref#13793)  Manufactured 1988, Deutz 4 cyl diesel engine on deck, mounted on GMC C-60 w/Detroit 8.2 liter diesel engine, 3L6 Moyno pump, wiggletail, breakout wrench, 3 winches, good condition, drilling    

DIEDRICH D-50  (Ref#251Nb)  Manufactured 1987, Duetz diesel engine, mounted on Ardco K Model buggy, cathead, Moyno 3L6 pump, 2 leveling jacks  Price:  $60,000   OFF MARKET

DIEDRICH D-25 (Ref#5005N) Manufactured 2008, mounted on rubber track carrier, tracks expand to 48” and contract to 24”, 4 leveling jacks, 27hp Kohler gasoline engine, winch, cathead, 2L6 Moyno mud pump, water swivel, 2010 “triple crown” double axle trailer, excellent condition.  PRICE:  $75,000  OFF MARKET

DIEDRICH D-25 (Ref#6584Na) Manufactured 1990, less than 500 hours, runs off of gas or propane, track mounted, 1 winch  Price:  $105,000

SONIC DRILL RIG SDC500-28 (Ref#4890Nc) mounted on 2004 International 6x4 with Cummins engine, Diedrich sonic head  Price on request

EIJKELKAMP COMPACT SONIC RIG (Ref#4890Nb)  POR

SIMCO 7000 (Ref#6199Na) Manufactured 2008, less than 2000 hours, mounted on Peterbilt 340 with Cat engine, Gardner Denver 5 x 6 mud pump, deck mounted grout pump  Price:  $295,000

SIMCO 7000  (Ref#7012N)  Manufactured 2004, mounted on Peterbilt truck with diesel engine, 30,000# mast, 12,000# hydrostatic hoisting winch, hydraulic retractable table, breakout wrench, 4 x 3 Mission pump (new Sept 2008), 3 hyd pumps, 4 leveling jacks, 10 rod carousel, includes 10 rods of 3-1/2” x 20’ pipe with 2-3/8 IF, drilling daily  Price:  $225,000 – OFF MARKET

SIMCO 5000  (Ref#121N)  Manufactured 1989, 400/200 air compressor, mounted on Ford 8000 truck with Ford 6 cyl diesel engine, winch, 3 jacks, 200’ drill pipe, 6” hammer, fully tooled  Price:  $120,000

SIMCO 5000WS  (Ref#13457)  Manufactured 1985, Joy air compressor, 5 x 6 mud pump, new Cummins 4BT deck engine, 3 winches, mounted on 1989 International 1900 tandem axle with DT466 engine, 10 speed RoadRanger transmission, 20’ stabilizer, 500’ drill pipe  Price on Request

SIMCO 5000 (Ref#6268N) shop built, PTO driven, mounted on 1981 International 2575 with 300 Cummins engine, 3 x 2 centrifugal mud pump, 185/100 air compressor, 8000# winch, grouter, desander, mud pan, mud mixer, stabilizer, bits, etc. fully tooled, 3 hydraulic leveling jacks, 435’ of 2 /78” drill pipe  Price:  $80,000  PRICE REDUCED:  $65,000

SIMCO 5000  (Ref#14036)  Sullair 200/100 air compressor, 4-1/2 x 5 Gardner Denver duplex mud pump, Deutz diesel on deck, mounted on 4 x 4 International truck with 330 gasoline engine, 300’ of Mayhew Jr 20’ drill pipe  Price:  $55,000

SIMCO 5000  (Ref#5053N)  Manufactured 1979, tophead, 200/300 air, 3 x 4 centrifugal mud pump, mounted n 1992 International tandem truck with diesel engine, Cummins deck engine (rebuilt), main winch, sandline, 260’ of 3-1/2” x 15’ drill pipe, stabilizer, main winch, sandline, 3 hydraulic jacks, fully tooled, rod box, 3-phase generator, toolbox, no water injection, fully tooled, ready to go  Price:  $85,000

SIMCO 5000 (Ref#9096Nb) Manufactured 1979, Deutz diesel deck engine, mounted on single axle International with International engine, 200’ of 2 3/8” IF drill pipe  Price:  $60,000

SIMCO 5000WS  (Ref#2524N)   Manufactured 1979, 4800 hours, developmental air, 2 x 3 centrifugal mud pump, Ford 300 Industrial gas deck engine, mounted on 1979 International truck with gas engine, sandline, mainline, 400’ of 20’ drill pipe, 4 stabilizers, some tools, 3 hydraulic leveling jacks, good condition, currently drilling  Price:  $75,000  PRICE REDUCED:  $45,000

SIMCO 5000  (Ref#13981)  Manufactured 1979, 300 CID Ford deck engine, mounted on 1979 tandem axle Ford L9000 with 3406 Cat diesel engine, 2 rear jacks, fully tooled, mud pan, 4 x 3 Mission mud pump, rod box, stabilizers, bits, 300’ of 3-1/2” x 15’ rods, 2 frame jacks  Price:  $60,000  PRICE REDUCED:  $50,000

SIMCO 5000  (Ref#15606)  Manufactured 1978, 5100 hours on rig, 4 x 3 x 13 Mission mud pump, King water swivel, both Sunstrand hydrostats, hydraulic oil cooler, Ford 300 Industrial gas engine on deck, 10,000# Gearmatic main winch, 4,500# Pullmaster auxiliary winch, electronic throttle control, 200 gallon water tank, 200 gallon mud pan, work lights, mounted on 1978 Ford 9000 truck with Cummins engine, 3 leveling jacks, no tools, no grouter, 315’ of 15’ Mayhew Jr drill pipe, rig needs some work  Price:  $22,500

SIMCO 5000  (Ref#14239)  Manufactured 1978, Ford 300 gas deck engine, mounted on GMC truck with gas/propane engine, sandline, main line, new 15’ stabilizer, 4 x 3 centrifugal pump, 1 front and 2 rear hydraulic leveling jacks, 250’ of 15’ Mayhew Jr drill pipe, good condition, currently drilling  Price rig only:  $65,000  Price for package with bits, subs, tools etc:  $70,000   OFF MARKET

SIMCO 5000 TOP HEAD ROTARY RIG  (Ref#11785)  Duetz diesel deck engine, mounted on Ford 9000 tandem axle truck w/3208 Cat engine, auto transmission, 200’ depth capacity, all tooling, good condition  Price:  $50,000

SIMCO 4500 (Ref#9045N) rebuilt Ford 200 CID deck engine, mounted on 1986 GMC 7000 with 366 engine, 2250 ft/lbs torque, 7000# hoist winch, 2700# sandline winch, pull up/down 10000#, 18’ tophead travel, 3 x 2.5 centrifugal mud pump, rod box, split table, hydraulic breakout wrench, GD air compressor, loaded, 400’ pipe  Price:  $45,000

Pipe trailer & addt’l bits, cones, etc available at extra cost

SIMCO TR2-4000  (Ref#2802Nab)  2 available, manufactured 1989 and 1991, track mounted with 3 cyl Duetz diesel engines, both fair running condition, no tools or pipe, needs TLC  Price:  $16,000 each

SIMCO TR4000-2  (Ref#3506N)  Cat steel tracks, Deutz 4 cyl diesel engine, 14,000# pullback, 5400 ft/lb torque, 12,000# Braden winch, Bean 410 piston pump, wireline winch, rod clamp, angle capability  Price:  $75,000

SIMCO 4000TR  (Ref#2147N)  Manufactured 1983, reworked by Simco 1995, coring head cores to 150’, drills to 200’, requires mud pump, 2 winches, 200’ of 10’ Mayhew Jr rods.  Work done:  new hoses, hydraulic pump rebuilt, new track drive motors, undercarraige bearings and bushings reworked, new replacement track pieces, engine leveller.  Located Canada  Price:  $35,000  PRICE REDUCED:  $33,500

SIMCO 4000 (Ref#9752Nb) less than 3000 hours, 4 cylinder Duetz diesel engine, 8 speed head, extendable mast, 8500# wireline winch, 12000# main winch, cathead, Bean pump  Price:  $120,000

SIMCO 2800 HS-HT (Ref#15575N) Manufactured 2007, only 870 hours, mounted on 2007 Ford F550, mud pan, 200’ drill pipe  Price:  $179,000  PRICE REDUCED:  $160,000

SIMCO 2800  (Ref#2828N)  Manufactured 2006, mounted on 2006 Ford F550 truck, 6 liter turbo diesel engine, PTO, 2 x 3 centrifugal mud pump, breakout wrench, auto hammer, 250’ of 10’ Mayhew Jr. rods, good running condition  Price:  $170,000

SIMCO 2800 (Ref#674N) Manufactured 2006, Multiple rpm drillhead (7485 ft/lbs / 0-670 rpm), 2” ID spindle, long stroke mast with adjustable extension, hoisting winch with cable (4500 lb cap.), tool handling winch with cable/2550 lbs., auger uide, slide base – in/out, wiggletail slide base, mating flange w/Ujoint NWJ pin 3-1/4” HS box, CME automatic hammer, top feed water swivel, 2 x 3 centrifugal mud pump, split rod handling table with flat wrench (NWJ), hydraulic breakout wrench, mounted on 2006 Ford F550 Super Duty 4 x 4, 19,000# GVW, 84” CA, Turbo diesel, All terrmain tires, 6-speed, white cab, AM/FM, air, towing package, aux throttle control, chrome wheels, vertical exhaust.  Steel diamond pattern deck (8’ x 11’), 3 hydraulic leveling jacks, under deck auger rack, (1) on-deck auger stanchion, factory mounting, brake controller, receiver hitch, DOT safety equipment, no cathead   Price:  $140,000

SIMCO 2800   (Ref#3135N)    Mounted on hydraulic carrier, Wisconsin 30hp gas deck engine, Moyno 3L6 pump, (2) 75 gallon water tanks, no cathead, outriggers, augers & tooling available

Price:   $33,000

Trailer available at additional cost

SIMCO 2800 HS(HT)  (Ref#1284N)  top head rig, manufactured 2005, 1900 hours, rebuilt PTO, mounted on 2006 Ford F550 4x4 truck with 6.0 diesel engine, 4 wheel drive, 6800 miles, new transmission and transfer case, new drillhead motor, new hydrostatic pump, new 2 x 3 centfifugal mud pump, water injection, 3 hyd leveling jacks, 300’ (100’ new) of 4-7/8” c 10’ light weight pipe, excellent condition  Price:  $185,000  PRICE REDUCED:  $115,000

SIMCO 2800 HT (Ref#9048N)  Manufactured 2004, tophead drive with tower extension, PTO, mounted on 2004 Ford F550 4x4 with 6.0 liter turbo diesel engine, only 1500 hours, hydraulic in-out slide base, 2x3 centrifugal mud pump, breakout wrench, 2 winches, rod box, stainless steel mud pan, 280’ of 3” PDQ drill rod, some tools, excellent condition  Price:  $147,500

SIMCO 2800  (Ref#961N)  Manufactured 2004, 3211 hours, 10,311 miles, 4-1/2” x 5” Gardner Denver duplex mud pump, mounted on single axle Ford 550 4x4 truck, 6 speed powered by Ford 6.0 diesel engine, PTO, no CDL required, 3 hydraulic leveling jacks, 11’ stroke, (2) winches 4500# and 2000#, tower telescopes to handle 20’ casing, rod rack, 0-185 rpm drill head, 200’ of 2-7/8” x 10’ flush wall Mayhew Jr drill pipe, excellent condition  Price:  $145,000  OFF MARKET

SIMCO 2800 HS/HT (Ref#9043N) Manufactured 2002, tophead drive, less than 5000 hours, mounted on 2002 Ford F500 4x4 with 7.3 powerstroke diesel engine, 2 x 3 centrifugal pump, 11’ stroke, stainless steel mud pan, in-out slide base, 2” swivel, hydraulic breakout wrench, auxiliary winch, 3 hydraulic leveling jacks, toolboxes, pipe racks, 200’ PDQ rod  Price:  $112,000

SIMCO 2800 HS/HT (Ref#9335N) Manufactured 2002, low hours & miles, PTO, mounted on Ford F550 4x4 with diesel engine, centrifugal mud pump, water injection, sandline, hydraulic breakout tongs, rod rack, mud pan, 12’ stroke, 4 hydraulic leveling jacks, 300’ of 3” x 10” drill pipe, stored inside, like new condition  Price:  $105,000

SIMCO 2800 HS(HT)HD  (Ref#1767Na)  multiple rpm drill head, hydraulic motor drive into 2-speed gearbox allows for both auger/rotary drilling and high speed core drilling.  Low gear 0 – 3600 ft/lb max torque 0 – 106 rpm.  High gear 0 – 700 ft/lb torque, 0-550 rpm.   Hollow spindle is 2” ID.  Use top feed water/air swivel.  Includes 7” 8-bolt mating flange for drill rods or auger adapter.  Equipped with Simco Model#4000 HD mast with mast extention, Wisconsin V 465D engine 60 hp, 7000 cathead winch with fixed disp. Pump, King 2J water swivel, rod handling table, hydraulic slips, breakout wrench, (2) mating flange 1-5/8 and water coarse pin, (2) hydraulic leveling jacks at rear of truck bed, rod rack and catwalk, aluminum mud pan, mounted on 1990 Ford F700 diesel truck, approx 300’ of 10’ x 2-7/8” Mayhew full hole drill rod, approx 250’ of 10’ x 2-3/8” drill rod, 60’ of 5’ x 6” (1-5/8 hex) sold stem auger hard surfaced, 70’ of 5’ x 4” solid stem augers, under bed tool box, misc bits, cutting heads, subs.  Needs tuneup and rear cylinder is leaking  Price:  $75,000  $55,000

SIMCO 2800 (Ref#7247N) Manufactured 1998, tophead drive, 600’ depth capacity, 3000 hours, 33,000 miles on truck, mounted on Ford F450 (not 4x4) with Superduty diesel engine, 11’ stroke, 4 x 5 mud pump, mud pan, bits, subs, etc, 450’ of 10’ joints, 1 front 2 rear hydraulic leveling jacks, ready to go   Price:  $85,000

SIMCO 2800HT  (Ref#8221N)  Manufactured 1996, mounted on Hydro tracks, 3 leveling jacks, 3.9L Cummins diesel engie (1600 hrs), 12’ drill stroke (tower telescopes to handle 20’), 150 gallon mud pit, 4-1/2” x 5’ failing mud pump, developmental air, 2000# and 8000# winches, carries 20 rods in rod rack, 10’ rods 2-3/8” APi thead (500’ flush joint), 4-1/2” x 10’ collar, 6-5/8” x 10’ collar, has drilled to 286’ 4”-6” diameter wells  Price:  $110,000

SIMCO HS HT 2800  (Ref#7318)  Manufactured 1995, high speed, high torque, new engine, mounted on 2002 Ford 550 4-wheel drive truck with diesel engine, 150 lb hammer, 4 x 6 Gardner Denver pump, 10’ – 20’ rods, complete with tooling  Price:  $85,000  OFF MARKET

SIMCO 2800 (Ref#7921N) Manufactured 1992, low hours, set up for auger & coring, mounted on Marooka carrier, turbocharged 4 cyl diesel engine, no auto hammer, safety hammer, cathead, winch, Bean 35 gpm pump, 200’ of HQ rods, 50’ of 4” HSA, 50’ of A rods  Price:  $80,000

SIMCO 2800 (Ref#316N)  Manufactured 1989, PTO, Mounted on 1100 Marooka with diesel engine, Beam pump, (2) winches  Price: $60,000

SIMCO 2800  (Ref#484N)  Manufactured 1987, mounted on 1978 Ford L9000 truck p/b 8V71 Detroit diesel in truck, 3 cyl Deutz diesel deck engine, 3 X 4 X 13 centrifugal mud pump, single line winch, breakout wrench, 11’ stroke, 3 leveling jacks, running condition, 280’ drill pipe  Price:  $45,000  OFF MARKET

SIMCO 2800  (Ref#6488N)  mounted on 1997 Chevy single axle truck with gas engine, 75’ auger, PTO  Price:  $33,000

SIMCO 2400 (Ref#4587N) Manufactured 2006, 40 hp diesel deck engine, only 100 hours, stored inside, 2 speed high torque tophead, mounted on 2006 Ford F550 4x4 with diesel engine, 74” stroke mast with hydraulic foot, 1800# hoisting winch, cathead with rope, in-out slide base, operators platform, 3 hydraulic leveling jacks, underbody toolboxes, auger racks, tools available  Price:  $95,000

SIMCO 2400 (Ref#7716N) Manufactured 2006, Deutz diesel deck engine, mounted on 2006 GMC Topkick all wheel drive, 120’ drill pipe, trailer, ready to go   Price:  $95,000  PRICE REDUCED:  $70,000

SIMCO 2400 (Ref#8035N) Manufactured 1997, tophead drive, freshly rebuilt deck engine, not mounted, auto hammer, in-out and side to side slide base, 1 winch, well maintained, some tools & augers available  Price:  $45,000

SIMCO 2400 SK1 (Ref#1419N)  Manufactured 1996, mounted on Dodge Ram 3500 with a Cummins diesel, Cathead, in and out slide base, 1800# winch, safety hammer, tool boxes, good condition, 80’ of 4 ½” x 5’ augers   Price $45,000

SIMCO 2400 DRILL RIG  (Ref#6654N)  10’ stroke, gas powered engine, mast winch, large water tank built in to truck bed, Moyno pump, mounted on 2005 Ford F550 XL Super Duty truck, power stroke Turbo diesel, automatic transmission, 4-wheel drive, dual rear tires, air conditioning, AM/FM CD player, 27,500 miles, warn winch on front of truck (12,000# rating)  Price:  $55,000  OFF MARKET

SIMCO 2400 SK-1  (Ref#657N)  10’ stroke, Deutz diesel powered engine (40 hp), mast winch, large water tank (built-in to truck bed), Moyno pump, 3 hydraulic leveling jacks, mounted on 2003 Ford F550XL Super Duty, power stroke turbo diesel engine, automatic transmission, 4 wheel drive, dual rear tires, air conditioning, AM/FM with cassette player, only 104,283 miles  Price:  $75,000  OFF MARKET

SIMCO 2400 (Ref#673N) Manufactured 1990, trailer mounted, Hercules gas engine, cathead, 1 winch, 5’ stroke, breakout wrench, 4 hydraulic leveling jacks  Price:  $32,500

SIMCO 2400  (Ref#5414)  Manufactured 1990, mounted on trailer, 5’ stroke, Wisconsin gas engine, 20’ mast, tool box, hand jacks, 3-1/4” augers  Price:  $25,000  OFF MARKET

SIMCO 2400 SK-1 (Ref#1986Na) Manufactured 1989, only 50 hours, mounted on Simco 3600 trailer, Wisconsin gas deck engine, high torque top head, cathead, mast extension, 74” mast stroke, 6000# pullback,, 30’ of 3 ¼”fd hollow stem augers  Price on request

SIMCO 2400 (Ref#15698)  Gas deck engine, mounted on ’95 Ford with gas engine, extended mast, cathead, 140# auto hammer, no tools, good condition, Price: $60,000

SIMCO 2400  (Ref#9493N)  Manufactured 1987, 3 cyl Deutz diesel engine, dual hydraulic pump and cooler, cathead, 140# hammer, 100 gallon wter tank, 20’ derrick, front hydraulic leveling jack, manual rear jacks, auger and rod racks, 2 tool boxes mounted undernearth chassis, mounted on 2003 Ford F450 4x4 with 6.0 turbo diesel engine, automatic transmission, front 5000# winch, 62,669 miles  Price:  $60,000

SIMCO SK24  (Ref#14407N)  Manufactured 1978, Yamar steel tracks  Price:  $18,000

SIMCO EARTHPROBE 200  (Ref#3014N)  Manufactured 2008, 60 hours (only used 4 times), unmounted, Kubota diesel on deck, 6’ mast, in/out side to side slide base, auger and auto hammer capability, 50’ 4” augers, 30’ 2” split spoons, wrenches, hammer and pins  Price:  $50,000

SIMCO EARTHPROBE 200  (Ref#1672N)  Manufactured 2005, Dubota diesel deck engine, only 106 hours, mounted on John Deere Gator 4x4 w/Kubota diesel engine, 72” stroke plus mast slide, hydraulic in/out slide base, auger drill head with 1000 lbs/ft torque, 60’ of 4” solid augers, excellent condition  Price:  $50,000

SIMCO EARTHPROBE 200 (Ref#1677N) Manufactured 2003, only 300 hours, gas deck engine, mounted on 1998 Ford F150 4x4 with V8 gas engine, in-out and side to side slide base, 9000 ft/lbs torque, auger attachment, no tools or augers available   Price:  $25,000

SIMCO EARTHPROBE 200  (Ref#15533)  Manufactured 1997, Kohler 18 hp gas engine on deck, mounted on 1997 Ford F250 w/powerstroke diesel, good condition, no tools or augers  Price:  $40,000

SIMCO EARTHPROBE 200 (Ref#5245N) Manufactured 1996, unmounted, 2 cylinder Koehler gas engine, Stanley pneumatic hammer, auger head attachment, tools and (6) new 1” rods  Price:  $16,000

SIMCO EARTHPROBE 200 (Ref#4480N)  Manufactured 1994, mounted on 1995 Ford F250 truck, 18 hp Briggs & Stratton deck engine, 5.7 ltr V8 gas in truck, no tools  Price:  $20,000

SIMCO EARTHPROBE 200  (Ref#13552)  Manufactured 1994, mounted on Yanmar rubber track carrier  Price:  $24,000

SIMCO EARTHPROBE 200 (Ref#1604N) Manufactured 1991, unmounted, 20hp Kohler propane engine, in-out slide base, set up for direct push, 6’ stroke, auger head attachment, 20’ of 1 ¼” direct push rod, some tools  Price:  $16,500

EARTHPROBE  (Ref#859Rb)  mounted on 1989 Ford F350 4 x 4 truck  Price:  $19,000

SIMCO EARTHPROBE  (Ref#284N) less than 900 hours, gas deck engine, mounted on 1995 Ford F250 4x4 truck with gas engine, hydraulic hammer, in/out slide base, aqll tooling, good condition  Price on Request

CANTERRA CT-450  (Ref#2200N)  Manufactured 1991, 625 cfm/220 psi air compressor (not working), 2000# sandline, 3 x 4 Mission centrifugal mud ump, grout pump, auger rack, 240 gallon water tank, Moyno pump, top drive rebuilt, mounted on 1990 Ford F900 truck with Ford 6 cyl diesel engine, 103,911 miles  Price:  $60,000

CANTERRA 450  (Ref#11327)  Manufactured 1991, Detroit diesel 285 hp deck engine, 625/220 GHH air compressor, mounted on 1991 Mack tandem axle truck with diesel engine, 5 x 6 mud pump, 4 leveling jacks, auger racks, hammer racks, good condition  Price:  $155,000

CANTERRA 411  (Ref#15389N)  Manufactured 1989, mounted on Ford LN8000 truck with 7.8L engine, 600/220 GHH air compressor, 5,000# torque head motor, Bean water injection, hammer oiler, hydraulic table and breakout wrench, 24’ stroke, single rod loader, rod trough with 200’ of 4-1/2” rod, 12,000# main and 1500# jib winch, new Funk pump box, many upgrades, Lincoln welder  Price:  $115,000  PRICE REDUCED:  $90,000

Available at extra cost:  615 Welco hammer and 3 x 4 mud pump

CANTERRA 312 BUGGY RIG  (Ref#5425)  Manufactured 1989, rig compressor and water tank mounted on separate buggy, designed to go anywhere.  Rig: mounted on 4 wheel articulating buggy, powered by 240 hp Cummins diesel engine, sliding angle mast, drills vertical to 45°, can drill to 1,000’, uses 10’ drill pipe, 3-7/8” diameter, air side inlet, reverse circulation package, 4” hammer, 1000’ of Matrix drill pipe x 10’, has been used in Alaska to the US desert.   Compressor:  900/350 Sullair compressor, mounted on 4 wheel buggy, John Deere log skidder C543, powered by 8V92 Detroit diesel, articulating.   Water buggy:  water tank mounted on John Deere log skidder 543, powered by 6V92 Detroit diesel.    Complete Package, ready to drill:  $525,000

CANTERRA CT-350  (Ref#14787)  Manufactured 1989, mounted on Ford F700 with diesel engine, 5 speed, 2 speed rear, 4 hydraulic leveling jacks, can load 20’ of auger, 24’ stroke, 50,000# hoisting load, pulldown 20,000# 0 – 130 fpm, pullback 26,000# 0 – 100 fpm, rotary direct drive 3-speed hydraulic motor with 2-1/8” hollow spindle, 10,000 ft/lb at 50 rpm, 3300 ft/lb 0-150 rpm, breakout wrench, top drive unlatches and swings out, handles up to 24’ x 14” diameter casing, drawworks winch, rod rack  Price:  $78,500

CANTERRA CT311 (Ref#5675N) tophead drive, manufactured 1988, PTO, mounted on Ford LNT9000 with 7.8 liter diesel engine, 185/100 air compressor, 3x4x13 centrifugal mud pump, Bowie pump, paddle mixer, 24’ stroke, rod trough, hydraulic breakout wrench, 4 hydraulic leveling jacks, 200’ of 4 ½” x 15’ drill pipe  Price:  $70,000  PRICE REDUCED:  $55,000

CANTERRA CT 311 (Ref#8816N) Manufactured 1987, PTO with brand new transfer case, mounted on 1987 Ford F700 4 wheel drive with Detroit diesel engine, 3000 ft/lb, 23 ½’ stroke, 36000# pullback plus double line on drawworks winch, Gardner Denver 5x6 mud pump, 135/150 developmental air compressor, toolboxes, 4 hydraulic leveling jacks, pipe rack, 400’ of 15’ x 3 7/8” OD drill pipe  Price:  $70,000  PRICE REDUCED:  $60,000

CANTERRA CT250  (Ref#1111N)  mounted on 1994 Ford L8000 truck (130,000 miles), 18 gal Bean injection pump, 3L8 Moyno pump, side mounted swing winch jib boom, main winch/sandline, side swing auger rack, rear mounted swing auger rack, 140# hammer, 600/200 air compressor, Cummins diesel deck engine w/clutch, single rod loader, 36” breakout wrench, rod spinner, large rod troff, side enclosed tool box/Fender toolbox  Price:  $170,000

CANTERRA TOP HEAD RIG  (Ref#3657N)  Manufactured 1992, 250 Cummins deck engine, mounted on 1992 GMC Topkick with Cat engine  Price:  $80,000

CANTERRA 250 (Ref#134N) Manufactured 1990, tophead drive, mounted on International 4x4 with diesel engine, 5x6 mud pump, 4 leveling jacks   Price on request

CANTERRA CT-150 (Ref#13064Na) Manufactured 1980, Cummins 3.9 liter diesel engine, not mounted, Parker 9000# winch, 3000psi hydraulic pump, 2000# wireline winch,  set up for auger, coring & wireline  Price:  $42,500

FOREMOST/MOBILE B-3500  (Ref#13892)  Manufactured 1997, 4 cyl Deutz deck engine (good shape), Moyno pump, mounted on 1997 Chevy 3500 tandem axle with new diesel engine and new transmission, 4 wheel drive, 2 rear leveling jacks, 18’ mast, currently drilling  OFF MARKET

FOREMOST MOBILE B-3500 (Ref#8090N) Manufactured 1997, only 3400 hours, diesel deck engine, mounted on 1997 Ford F350 4x4 with 7.3 powerstroke diesel engine, in-out and side to side slide base, Moyno 3L6 pump, toolboxes, pipe racks, 2 rear hydraulic leveling jacks  Price:  $48,500  PRICE REDUCED:  $38,500

MOBILE B-4300 (Ref#6583Nb) Manufactured 1996, less than 7800 hours, PTO, mounted on 1996 International T444E with diesel engine, angle capability to 45 degrees, 4 winches, 14’ stroke, auto chuck, 8 speed head, 53 head, Moyno 3L6 pump, Bean pump, rod racks  Price:  $110,000

FOREMOST/MOBILE 5500 (Ref#4890Nd) PTO, mounted on Ford F550 4x4 with diesel engine  Price:  $60,000

MOBILE B80 (Ref#701N)   Completely rebuilt one year ago, manufactured 1984,  mounted on 2001 Freightliner with 430hp Cat engine, Sullair 330CFM on board air compressor, new auto hammer, extruder, 3 winches, 3 leveling jacks, 14’ stroke, derrick can handle 20’ joints of pipe, Shelby tubes, split spoons, NX core barrel, and 10 new bits, ready to go  Price:  $265,000

MOBILE B-80  (Ref#1981N)  Manufactured 1986, excellent condition, mounted on Ford 8000 truck with Cat 3208 engine, PTO, hydraulic winch, 160# hammer, tools and augers included  Price:  $100,000

MOBILE B-80  (Ref#203N)  Manufactured 1982, mounted on Ford LNT800 truck, Deutz diesel 4 cyl deck engine, Ford gas engine in truck, 750/150 Grummer Schmidt screw compressor powered by 8.3 Cummins Turbo engine, 14’ stroke, cathead, 9 gpm Bean water injection, 400’ of 3-1/2” drill pipe with 2-3/8 IF thread, 6” CP hammer, 6” Numa hammer  Price on Request

MOBILE B-80  (Ref#14909)  Manufactured 1978, fully refurbished, mounted on 1978 Ford F8000 truck with diesel engine, PTO, 5 x 6 mud pump, 3L6 Moyno pump, 6000# and 2000# hoists, cathead, hydraulic breakout wrench, 3 jacks, no tools or pipe, good condition  Price:  $65,000

MOBILE BK66 (Ref#3941N) Manufactured 2000, low hours, John Deere diesel deck engine, mounted on 2000 Ford F650 (not 4x4) with diesel engine, 25’ quick disconnect mast, hydraulic cathead, in-out and side to side slide base, 2 winches, Moyno 3L6 pump, auger & rod racks, 3 hydraulic leveling jacks, no angle capability, no auto hammer, toolbox, augers & tooling available  Price:  $92,000  REDUCED PRICE:  $75,000

MOBILE B-65  (Ref#5167)  Manufactured 1970, 30’ mast, mounted on Ford 6 cyl truck w/Pony motor (truck needs work), side base, hyd jacks  Price:  $30,000

MOBILE B-61  (Ref#5717Na)  Manufactured 1989,  Diesel (Cummings?) with break out wrench, rod clamp, Gimble coupling, set up with 2 to 3 winches as well as wire line winch, slide base, wiggle tail, mounted with a Moyno L8 pump,.  The rig carries 40’ NWJ 10’ rods, 40’ of 5’ NWJ rods, N core barrel with bits, 6” 4” & 3” casing with drive shoes, 40’ of 4.25 Mobil augers,  140# safety hammer, 300 # donut drive hammer, approximately  300 gallon water tank, assorted tools subs roller and auger bits.   Rig is mounted on a 1989 Ford LN8000 diesel tandem axle.  Truck GVW 50,000. Rig fuel consumption is 5 to 10 gallons per day. Owner/operator since the rig was new  Price:  $70,000

MOBILE B-61  (Ref#5717Nb)  Approx year of manufacture 1982,  Diesel with CME break out wrench, rod clamp, set up with 2 to 3 winches with capability of using wire line system, slide base, mounted with a Moyno L8 pump transmission drive for various speeds and flows.  The rig carries 40’ NWJ 10’ rods, 40’ of 5’ NWJ rods, N core barrel with bits, 4” casing with drive shoe, 40’ of 4.25 Mobil augers,  140# safety hammer, 300 # donut drive hammer, approximately  300 gallon water tank, assorted tools subs roller and auger bits.   Rig is mounted on a 1986 International diesel tandem axle.  New front tires  Price:  $55,000

DIEDRICH D50  (Ref#5717Nc)  Manufactured 1988, skid mounted, gas engine, 2 winches, Moyno L6 pump, slide base, tower can be raised to ½ mast for 18’ head clearance for inside drilling, currently mounted on all terrain Bombardier which is transported on heavy duty flat bed car carrier. Price:  $50,000

Portable Tri-Pod drilling system

Equipment Listing

                6” ODEX casing advancement system with drive shoes and hammers 60’

                4” ODEX casing advancement system with drive shoes and hammers 110’

                4-1/2” drill rod in 5’ lengths 70’

                5” casing used once 40’

                4” casing 50’

                3” casing 100’

                4.25 Mobil augers 90’with bits

                4.25 Acker augers 80’ with bits

6-1/4 Mobil augers 95’ with bits

                8-1/4 Mobil augers 100’ with bits

                Vane shear system

                4” well packer system

                6” well packer system

12 rig stabilization mats 4X8

2 steam cleaners

Shop tooling and equipment

Assorted well supplies pvc & stainless

PACKAGE PRICE:  $180,000

THREE RIG PACKAGE: ALL RIGS SETUP FOR AUGER AND CORING (Ref#1808N)

MOBILE B-61  Ford 300 6 cyl gas deck engine, mounted on 1987 Ford F800 truck, water injection, cathead, 3 winches, 20’ mast, extruder for core sampling, 3 jacks, auger racks, tools

MOBILE B-53 353 Detroit deck engine, mounted on 1995 GMC truck with diesel engine, 20’ mast, cathead, extruder for core sampling, auger racks, 3 leveling jacks

Package Price:  $60,000

MOBILE B61 HDX (Ref#174N) Manufactured 1995, mounted on 1984 International, Moyno 3L* pump, new Bean injection pump, swing out auger racks, toolboxes, 4 leveling jacks, tools  Price:  $95,000

MOBILE B61 (Ref#2906N) Manufactured 1994, diesel deck engine, mounted on 1994 Ford single axle truck with diesel engine, some tools    Price on request

MOBILE B-61 HDX  (Ref#1241N)  New 300 Industrial gas deck engine, mounted on 2007 Ford F650 (not 4x4) with Cummins diesel engine, cathead, in/out and side to side slide base, 3L8 Moyno pump, 3 winches, 3 hyd leveling jacks, underbody auger racks, toolboxes, excellent condition  Price:  $125,000

Tools and augers available at additional cost

MOBILE B-61HD  (Ref#1070N)  Manufactured 1993, Cummins diesel deck engine, main auxiliary winch, safety winch, 3L8 Moyno pump, auger racks, mounted on Ford F800 truck, auger racks, tool boxes   Price:  $65,000  

OFF MARKET

Pipe available at extra cost

MOBILE B-61  (Ref#8699N)  Manufactured 1992, gas deck engine, mounted on 1981 Ford F700 truck (not 4x4) with gas engine, safety hammer, 3 hydraulic jacks, 2 winches, 250 gallon water tank, auger racks 

Price no tools:  $30,000

100’ auger  rod AWJ, split spoon samples

Price with tools:  $35,000

MOBILE B-61 HDX  (Ref#1601N)  Manufactured 1991, mounted on 2000 International 4800  4x2 truck with 230 hp DT466 Turbo diesel, 20,000# torque, 29’ mast, 8,500# main hoist, 3,200# aux hoist, 900# capacity Mobile Safe-T drive sampling hoist, 2” hex quick change auger adapter with quill for top feed swivel,  in/out slide base, sideways slidebase, toolbox, auger racks, 250 gallon water tank, (3) hyd jacks, hyd breakout, rebuilt in Oct 2003  Price:  $120,000

MOBILE B-61 HDX  (Ref#1989N)  Manufactured 1991, diesel deck engine, mounted on Ford F800 truck with diesel engine, safety driver, 140# drop hammer, 3 winches, hydraulic extruder, breakout wrench, Moyno 3L8 pump, no angle capability, no auto hammer, 3 hyd leveling jacks, good condition, currently drilling  Price:  $95,000

Tools and augers available at exrtra cost

MOBILE B61 HDX  (Ref#4238N)  Manufactured 1990, diesel deck engine, mounted on truck with diesel engine, in/out side to side slide base, Moyno pump, no auto hammer, cathead, safety driver  Price:  $115,000

MOBILE B-61 HDX  (Ref#1268N)  Manufactured 1990, Cummins 4BT deck engine, mounted on 1990 Ford 8000 truck with diesel engine, hydraulic cathead, Shelby tube extruder, in/out and side to side slide base, Moyno 3L8 pump, 17’ x 2-3/8” kelly, Bean water injection pump, 2 winches, set up for auger and coring, no tools or pipe, no auto hammer, 2 rear hyd jacks, swing out auger racks, toolboxes.  (sandline and breakout wrench available, but not on rig), good condition  Price:  $55,000

MOBILE B-61 HDX  (Ref#2483N)  Manufactured 1990, Cummins diesel engine, mounted on 1992 Ford F800 with diesel engine, 250 gal water tank with Denison pump  Price, rig only:  $90,000

Tool and augers available at extra cost

MOBILE B-61HDX  (Ref#15453)  Manufactured 1990, Cummins 4BT deck engine, mounted on 1991 Ford F800 truck (not 4x4) with diesel engine, coring head, 250 gallon water tank, safety driver, mainline winch, sandline winch, aux. winch, in/out and side to side slide base, standard mast, 2 auger racks, toolbox, breakout wrench, 3 hyd leveling jacks, rotary head needs work, needs new bearings and seals, no Moyno pump, rust on deck  Price:  $80,000

MOBILE B61  (Ref#893N)  mounted on 1990 Ford 3800 with diesel engine, 152,770 miles, fluted Kelly, 6 x 5 x 6 Gardner Denver FXG duplex pump, fluid ends rebuilt 2006, Moyno 3L6 pump  Price on Request

MOBILE B-61HD  (Ref#207N)  Manufactured 1989, mounted on 1996 Ford L8000 truck single axle truck with diesel engine, Moyno 3L8 pump, safety driver auto hammer, cathead, 2 winches, 2 auger racks, toolbox, in out/side to side slide base, 500 gal water tank, 3 jacks, no tools no augers, currently drilling  Price:  $75,000

MOBILE B-61  (Ref#10027N)  Manufactured 1989, mounted on 1990 Ford L8000 truck with Cummins 4BT-3.9 deck engine, (4) leveling jacks, 3 winches, rebuilt GD 5 x 5 mud pump, Moyno L6 pump, 500 gal water tank, slide base, hydraulic extruder, cathead, in/out side to side blide base   Price:  $85,000

MOBILE B-61  (Ref#9741)  Moyno CDR mud pump, mounted on 1979 International truck powered by 409 gasoline engine, 6 cylinder diesel engine on deck, 500 gallon water tank, auger rack, set up for mud drilling  Price:  $40,000

MOBILE B61 (Ref#459N)   Manufactured 1989, mounted on Ford 800, 6 cylinder Ford 300 deck engine, 429 gas engine in truck, 3L8 Moyno pump, (2) safety hammers, wireline cable, cathead, 200 gallon stainless steel water tank, good running condition

Price: $67,000

Available at additional cost: 140’ of 5” & 6” augers, 100’ of hollowstem augers, 60’ of AW rod, 25’ of AJ rod

Package Price: $80,000

MOBILE B-61HD  (Ref#9742)  Manufactured 1989, Ford gas deck engine, Moyno 3L6 pump, mounted on 1989 Ford F800 truck with diesel engine  Price:  $55,000

MOBILE B61 HD  (Ref#200N)  Manufactured 1988,brand new Cummins deck engine, Moyno 3L8 pump, 30’ mast, 8000# main winch, aux winch, safety driver, mounted on Ford F800 tandem axle truck, no tools, no pipe, rig in running condition  Price:  $50,000 

MOBILE B-61HD  (Ref#1464N)  Manufactured 1988, mounted on 1985 GMC tandem axle truck, DT dieselengine, 3 leveling jacks, 3 winches, 250 gallon water tank with pump, 2 swing out auger racks, 3 tools boxes, Cummins deck engine, good condition, currently drilling  Price:  $85,000

Available at extra cost:   Support Equipment Package includes D-Con trailer, hot water washer, drop hammers, drills extensions, adaptors, rods, split tube samplers, 1.5” and 2.5”, (+- 100 samples tubes), 10-15 bits, 6” & 12” cycling through rebuilding process, used hollow stem auger, cycling through rebuilding process, approx (60) ea 6”, 8” 12”, practically new (24) 6”,  auger bolts and bushings, other miscellenaous tools and equipment   Support package: $25,000

MOBILE B-61 PACEMAKER  (Ref#12091)  Manufactured 1988, rebuilt Detroit 353 diesel deck engine, 300 gallon fuel tank, mounted on International 1900 tandem axle w/466 Dt diesel (rebuilt Dec 2002), 10 speed transmission, 2L3 Moyno pump, main winch 20,000# wireline, 3500# aux winch, cathead, 40’ of 6-1/4” augers, 2 rear, 1 front hyd leveling jacks, auger rack, no tools, excellent condition  Price:  $60,000

MOBILE B-61HD  (Ref#6646N)  Manufactured 1988, Cummins 4 cylinder deck engine (rebuilt 10/05), 250 gallon water tank, 3L6 Moyno pump, in/out slide base, 8000# and 13,000# winch (one safety drive, one heavy duty), 3 toolboxes, plus 2 toolboxes for storing shoves, etc., mounted on 1989 Ford F800 truck with 147,000 miles, Cummins engine, 3 hydraulic leveling jacks, (2) 140 lb hammers, 90’ 8” hollow stem auger, misc tooling   Price:  $80,000

Extra top head drive and right angle drive available at extra cost.

MOBILE B-61  (Ref#15193N) Manufactured 1987, mounted on 1987 Ford F800 truck with diesel engine, Cummins 4 cylinder diesel deck engine, 28’ mast, 250 gallon wter tank, 3L6 Moyno pump and Bean high pressure pump, 3 leveling jacks, 2 swing out auger racks, 2 winches, wireline hoist, hydraulic breakout wrench, hydraulic cathead, hydraulic rod clamp, 5 toolboxes, flexible setup for core, rotary and/or auger drilling   Price:  $75,000

Available at extra cost:   700’ of HQ drill rods, 100’ of 4” hollow stem augers, some NW tooling, 140# hammer bits

MOBILE B-61XD  (Ref#1699N)  mounted on Ford 9000 truck, 2 heads coring/augering, 3 winches, cathead  Price:  $50,000

MOBILE B-61HD  (Ref#6129)  Manufactured 1987, 3L8 Moyno, Ford Industrial 300 gas, mounted on Ford F700 with 370 gas engine, 100’ auger, safety driver, 100’ BW rod  Price:  $40,000

MOBILE B61 (Ref#3684Nb) Manufactured 1985, mounted on 1986 International F1954, 4 ½ x 5 mud pump, 4 hoists, rod holder, breakout wrench, Failing style pulldown & Kelly, 1000 gallon water tank  Price:  $55,000

MOBILE B-61  (Ref#1988N)  Manufactured 1985, 183,000 miles, 5300 hours, powered by Ford gasoline engine, cathead, water tank, 3.6L Moyno pump, 2 winches, new feed cylinder, winch on front, augers racks, toolboxes  Price:  $60,000

MOBILE B-61  (Ref#15531)  Manufactured 1980, mounted on 1985 Ford F8000 tandem axle truck, Bean 35 mud pump, diesel engine, tools  Price:  $45,000

MOBILE B-61  (Ref#3532N)  Manufactured 1980, mounted on 1989 Mack truck, 8.3 diesel deck engine, 4BT diesel Cummins in truck, 3L8 Moyno pump, in/out slide base, breakout wrench, good running condition, no tools  Price:  $95,000

MOBILE B-61  (Ref#9785N)  mounted on International Paystar S1900 Series 4-wheel drive diesel, Cat diesel engine, 6 cyl Ford 300 diesel deck engine, cathead, 2 auger racks, 4 speed rotary transmission, heavy duty right angled drive gear box on rotary, power steering, 2 leveling jacks, 10:00 x 20 tires  Price:  $75,000

MOBILE B-61  (Ref#9662)  Two available, manufactured 1979, mounted on tandem axle GMC Brigadier with 6V71 Detroit diesel, Moyno 3L8 pump, Ford 300 6-cylinder gas engine on deck    Price:  $45,000     Also a similar 1975 $30,000

MOBILE B-61  (Ref#15038)  Manufactured 1978, 300 Ford Industrial gas deck engine, mounted on 1990 International tandem axle truck with diesel engine, 35000 miles, low miles, no pipe, no tools, Bean 35 pump, gas engine   Price:   $40,000

MOBILE B-61  (Ref#5506N)  mounted on 1975 Ford truck with gas engine, diesel deck engine, Moyno 3L6 pump, cathead, in/out slide base, hydraulic rod chuck, 2 hoists, 3 hydraulic leveling jacks   Price:  $24,000

MOBILE B-61  (Ref#3676Nb)  Manufactured 1974, 6 cyl John Deere diesel engine, 5000# winch, wireline winch, stainless steel water tank and comes with extra turntable  Price:  $17,500

MOBILE B-61  (Ref#12862)  Manufactured 1972, Ford 6 cyl gas deck engine, mounted on 1972 International single axle 4 wheel drive w/gas engine, mud pump, hydraulic chuck, 120’ of 6-5/8” augers, auger rack, 3 winches, cathead, toolbox, water tank, 2 rear 1 front hyd leveling jacks, some pipe, good condition, currently drilling  Price:  $35,000

MOBILE B-61-HDX  (Ref#11596)  Manufactured 1972, 6 cyl Ford gas deck engine, mounted on 1992 International 4900 single axle truck, top head drive, 4 x 5 GD mud pump, cathead, Shelby tube extractor, 4-1/2” hollow stem augers, auger rack, 1 winch, front and rear hydraulic leveling jacks, good condition  Price:  $45,000

MOBILE B-61  (Ref#4450N)  Manufacuted 1969, 6 cyl Ford Industrial deck engine, mounted on 1969 GMC truck (needs replacing), 100’ auger, misc tools,  Make Offer

MOBILE B-61 (Ref#2412Nc) 453 Detroit deck engine, mounted on Ford L9000 tandem axle truck, Moyno pump  Price:  $49,500

MOBILE B61HD (Ref#15452N)  Engine, Mast, Augers, Complete, Truck needs work  Price: $95,000

MOBILE B-61 PACEMAKER  (Ref#9217N)  Manufactured 1969, Ford Industiral 6 dyl gas deck engine, mounted on GMC 550 with 8 cyl gas engine, 30’ mast, cathead, 100’ of flight auger, 60-70’ drill rod, fully tooled, excellent condition  OFF MARKET

MOBILE B-59  (Ref#998N)  Manufactured 1995, Cummins 4BT turbo diesel deck engine, 30’ quick disconnect mast, 5,000# cathead, mounted on Ford F800 with Cummins turbo diesel, 45,000 oroginal miles, dual 50 gallon fuel tanks.  13,500 ft/lb torque, 700 rpm top spindle speed, 2- speed right angle drive, 8,500# capacity Pullmaster main hoist, 4,500# capacity Pullmaster auxiliary hoist, 900 lb. capacity Mobile Safe-T driver sampling hoist, Clark 18000 3-speed automatic power shift transmission, 250 gallon water tank with under tank storage compartments, aux air compressor, 2 hinging auger racks, Moyno 3L6 water pump, (3) 36” hydraulic stabilizer jacks, approx 2700 hours and well maintained,   Price:  $115,000  PRICE REDUCED:  $90,000

MOBILE B59 (Ref#3654N) Manufactured 1995, Cummins 4BT turbo diesel deck engine, mounted on 1995 Ford F800 with Cummins turbo diesel engine, 13,500 ft/lb torque, 30’ QD mast, 8500# Pullmaster main hoist, 4500# Pullmaster auxiliary hoist, 900# safety driver sampling hoist, 5000# cathead, 250 gallon water tank, auxiliary air compressor, Moyno 3L6 pump, auger racks, 3 hydraulic leveling jacks  Price:  $135,000  OFF MARKET

MOBILE B59 (Ref#4302N) Manufactured 1995, Cummins 4BT deck engine, mounted on 1995 Ford FT900 tandem axle truck with 250hp Cummins engine, 10 speed RR transmission, one owner rig, well maintained, Moyno 3L8 pump, cathead, wireline, safety driver, 4000# & 8500# hoists, 250 gallon water tank, breakout wrench, no auto hammer, rod clamp, in-out & side to side slide base, auxiliary air compressor, 2 auger racks, toolboxes, 1 front & 2 rear hydraulic leveling jacks  Price:  $95,000

Augers available at extra cost

MOBILE B-59  (Ref#584N)  2 available, manufactured 1993 and 1994, Cummins 6 cyl Turbo diesel deck engine, mounted on 2004 Fregihtliner FL70 with dieselengine, (1) has Moyno 3L8, (1) has Moyno 3L6, 3 winches, no cathead, no auto hammers,  3 hydraulic leveling jacks, good condition, currently drilling, no tools avalble  Price:  $115,000 each  OFF MARKET

MOBILE B59 (Ref#2414N) Manufactured 1992, Cummins 4BT deck engine, mounted on International 4900 with diesel engine, no auto hammer, safety driver, in-out slide base, breakout table & wrench, 2 heavy duty winches, Moyno 3L6 pump, 600 gallon stainless steel water tank, 4 hydraulic leveling jacks, no tools or augers available  Price:  $80,000  PRICE REDUCED:  $65,000

MOBILE B-59  (Ref#2017N)  Manufactured 1992, Cummins 4BT deck engine, mounted on Ford F800 (not 4x4) with Ford diesel engine, wireline, mainline and auxiliary winches, safety driver, no cathead, no auto hammer, in/out and side to side slide base, 3L6 Moyno pump, 250 gallon water tank, 3hyd leveling jacks, good condition, currently drilling  Price:  $89,000

No tools or augers available

MOBILE B-59 (Ref#3607N) Manufactured 1989, Cummins deck engine, mounted on 1995 Ford FT900 with Cummins engine, recent in-frame overhaul, Moyno 3L8 pump, 2 winches, hydrostatic drive, swing out auger racks, 2J water swivel, auto hammer, 25’ quick disconnect mast, 500 gallon water tank  Price:  $73,000

MOBILE B-59 (Ref#6794Ra) Cummins deck engine, less than 900 hours, mounted on 1992 Ford F800, 12000 ft/lb torque, 8500# Pullmaster main hoist, 3200# Koenig aux hoist, side to side slide base, air compressor, 250 gallon water tank, no tools or augers available  Price:  $95,000

MOBILE B-59 (Ref#136N)  Cummins 3.9 diesel engine on deck, Mobile Satety driver, SPT hammer, 3L8 Moyno pump, 2 winches, Auger racks, toolboxes, mounted on Navistar 4900 4x2 w/ diesel engine, 5 speed transmission  Price: $100,000

MOBILE B59 (Ref#3687Nf) Cummins 4 cylinder deck engine, only 4000 hours, mounted on 1994 Ford F800 with Cummins 6 cylinder engine, Moyno 3L6 pump, 300 gallon water tank, split boom, cathead, rod jaws, hydraulic breakout wrench, wireline winch, auciliary winch, main hoist, safety driver, air compressor for air tools, 2 swing out auger racks, 3 leveling jacks, toolboxes   Price on request

MOBILE B-59 (Ref#2412Nb) 4 cylinder Cummins deck engine, mounted on ATV with 453 Detroit diesel engine, 3 lines, set up for swamp work  Price:  $75,000

MOBILE B-57  (Ref#467R)  mounted on International 4 x 4 truck with diesel engine, diesel deck engine,Moyno pump, 140# auto hammer, Safe-T driver, 3 hydraulic jacks, high speed range 0-665 rpm, low speed range 0-82 rpm, feed stroke 6’, max torque 10,896 ft/lbs  Price:  $57,500

MOBILE B-57  (Ref#5582Na)  Manufactured 1989, mounted on 1991 Morooka with 4144 hours on motor, 85% tread, Mission pump, 120’ flight augers  Price:  $120,000

MOBILE B-57  (Ref#5582Nb)  Manufactured 1989, rig has 4084 hours,  mounted on 1970 Military 6x6 5-ton truck, truck in perfect condition (1525 hours o gauge), 4000 psi heater pressure washer, 2 cycle diesel generator/welder.  Price:  $95,000

Also available with above two rigs:  (approx.)

(22) 5”, 5’ flight augers

(6) 1’ AWJ pipe

(6) 5’ AWJ thread

(5) 10’ AWJ thread

(28) 2-1/2’ Shelby tubes

(12) 5’ AWJ pipes

(11) 3”, 5’ flight augers

(2) rock drill bits

(1) mud pit

(1) generator “xtreme power train” 4500 watts – 5500 watts

(3) 2-1/2’ split spoons

(1) 4000 psi/heated coild power washer

(1) Northern Industrial welder MIGI35

(13) 5’7” hollow stems

(10) 5’10” hollow stems

(1) 15’ x 2” water hose with filter

(1) 20’ x 2” water hose (clear)

(1) 10’ x 2” water hose

Package Price for two rigs and tooling:  $275,000 

PRICE REDUCED:  $130,000 FOR TWO RIGS AND TOOLING

MOBILE B57 (Ref#6500N) Manufactured 1988, Ford 6 cylinder industrial gas deck engine, mounted on 1995 Ford F800 (not 4x4) with diesel engine, in-out and side to side slide base, 140# auto hammer, 3 winches, quick disconnect mast, Moyno 3L6 pump, 250 gallon water tank, auger racks, toolboxes, 3 hydraulic leveling jacks  Price:  $80,000  OFF MARKET UNTIL JAN 2012

MOBILE B57  (Ref#3687Nc) Ford 6 cylinder deck engine, only 3700 hours, mounted on 1987 Marooka MST 800 carrier with Mitsubishi 4 cylinder engine, Moyno 3L6 pump, cathead, main hoist, auxiliary hoist, 150 gallon water tank, auger rack, 1 front & 2 rear leveling jacks, rod rack   Price on request

MOBILE B57  (Ref#2600N)  2 available, manufactured 1989, mounted on Ford F700 truck with Ford gas engine, safety driver, 3L6 Moyno pump, hydraulic breakout wrench, in/out side to side slide base, auger racks, 3 jacks, 140# auto hammer, (1) working, (1) needs new engine  Price on Request

MOBILE B57 (Ref#2245N) Manufactured 1989, Ford 300 gas deck engine, mounted on 2000 Ford F650 (not 4x4) with Cat engine, auto hammer, in-out and side to side slide base, Moyno 3L8 pump, 200 gallon water tank, water swivel, 3 hoists, 3 hydraulic leveling jacks, auger racks, toolbox, no tools or augers available  Price:  $65,000

MOBILE B-57  (Ref#4567N)  Manufactured 1988, DT466 6 cyl gas deck engine rebuilt with only 125 hours, mounted on 1995 International single axle with diesel engine, hydraulic sample extruder on deck, 8000# Koenig winch, Ramsey aux winch, 2 aux winch lines on mast, Moyno 3L6 pump, cathead, 250 gallon water tank, auger racks, in/out and side to side slide base, no auterhammer,  60’ of 4-1/2” augers,  ready to go, good condition  Price:  $69,500

MOBILE B57 (Ref#2842N) Manufactured 1991, Ford 300 6 cylinder gas deck engine, mounted on 1990 Ford F700 (not 4x4) with 429 gas engine, cathead, in-out and side to side slide base, no auto hammer, Moyno 3L6 pump, 250 gallon water tank, pipe racks, auger racks, toolboxes  Price:  $80,000  PRICE REDUCED:  $52,000

MOBILE B57 (Ref#1562N) Manufactured 1990, mounted on Ford F700 with gas engine, pullmaster winch line, cathead, new Wheatley pump, 3 hydraulic leveling jacks, good condition, drills daily  Price:  $32,500

MOBILE B-57  (Ref#6383N)  Manufactured 1990, 7800 hours, diesel deck engine, mounted on Ford F800 (not 4 x 4) with diesel engine, main, auxiliary and safety driver hoists, in/out and side to side slide base, breakout wrench, 200 gallon water tank, 2L4 Moyno pump, 2 swing out auger racks, toolbox, 3 hyd leveling jacks, no cathead, no tools or augers, good condition  Price:  $65,000

MOBILE B-57  (Ref#9961Na)  Manufactured 1990, 3L6 Moyno pump, 4BT Cumins engine (approx 3000 hours), automatic hammer, 8500 lb winch, 3200 lb winch, manual chuck, safety driver winch, rod clamps and breakout wrench, swing out auger racks (both sides), tool boxes above and below deck, rod box under tool boxes, rod box under deck, in/out slide base, side to side slide base, above deck auger rack,  mounted on 1990 Ford F800 truck, 6 cylinder Ford diesel engine (approx 145,000 miles), 5 speed transmission, 2 speed differential, 2x5, good tires,

Price for rig only:  $85,000

Available at extra cost:

100’ 4-1/4 tri-lock augers, 100’ of 3-1/4 tri-lock augers, 100’ NWJ pipe, (3) 3-1/4 auger heads, (2) 2” split spoon sampler with sub to NWJ, (5) 4-1/4” tri-lock auger heads, (1) 4-1/4 center bit,  

MOBILE B-57  (Ref#4135N)  Manufactured 1989, Ford 6 cyl 300 gas deck engine, mounted on 1994 GMC Topkick with 3116 Cat engine, 3 hyd jacks, 3 winches (10,000#, 4,000# and safety driver), Moyno pump, cathead, wiggletail,  no water injection, no air, 300 gal water tank, toolbox, auger racks, rod racks, breakout wrench, no tooling or augers  Price:  $70,000

MOBILE B57 (Ref#9606N) Manufactured 1989, 300 6 cylinder gas deck engine, mounted on 89 Ford F700 4x4 with 429 gas engine, cathead, Moyno 3L6 pump, in-out and side to side slide base, no auto hammer, 200 gallon water trank, no tools or augers available  Price:  $45,000

MOBILE B-57  (Ref#9961Nb)  Manufactured 1989, 4BT Cummins engine (approx 850 hours), automatic hammer, 8500 lb winch, 3200 lb winch, safety driver winch, rod clamp and breakout wrench, swing out auger racks (both sides), tool boxes above and below deck, rod box under tool boxes, rod box under deck, in/out slide base, side to side slide base, above deck auger rack, mounted on 1990 Ford F800 with 6 cylinder Ford diesel (approx 135,000 miles), 5 speed transmission, 2 speed differential, 2x6, good tires, 50’ of 4-1/2” tri-lock auger, 50’ of NWJ rod, (2) 2” split spoon sampler with sub to NWJ, (2) 4-1/4” auger heads, (1) 4-1/4” center bit 

Price:  $95,000   Price for rig only:  $85,000  OFF MARKET

MOBILE B-57  (Ref#7480)  Manufactured 1989 (830 hours), high capacity Bowie mud pump, Longyear automatic chuck, 2 winches, cathead, no hydraulic breakout, 489 V8 gas on deck, 1500 hours, mounted on Ford F700 truck with 6 cyl Industrial gas engine, 350 gal water tank, (2) 40 gal saddle fuel tanks,  (11,000 miles), Price without tools:  $70,000 

Available at extra cost

MOBILE B-57  (Ref#3645N)  Manufactured 1988, Ford Industrial 300 6 cyl gas engine on deck and in buggy, mounted on Ardco buggy 4 x 4, Moyno pump, in/out slide base, toolbox, auger racks, 2 winches, 4 hyd levelingjacks, no tools  Price:  $60,000

MOBILE B-57  (Ref#3676N)  Manufactured 1988, Cummins for BT diesel, Pullmaster winch, wireline, Moyno pump, stainless steel water tank  Price:  $60,000

MOBILE B57 (Ref#14668N) Manufactured 1987, diesel deck engine, mounted on 1994 Ford F800 with diesel engine, 2 winches, drop hammer, cathead, Shelby tube extruder, slide base  Price:  $63,000

MOBILE B-57  (Ref#1102N)  Manufactured 1987, 6 cylinder Ford pony motor, 400 gallon water tank, 3L8 Moyno pump, swivel tail slide base, cathead with hammer, Pull Master H-8 8500# winch, rod chuck, mounted on 2000 International 4700 truck, breakout wrench, under deck auger racks, on deck/under deck toolboxes  Price:  $60,000

MOBILE B57 (Ref#3684Na) Manufactured 1986, mounted on 1986 International F1954, 4 ½ x 5 mud pump, in-out & side to side slide base, 140# auto hammer, rod holder, Failing style pulldown & Kelly, 4 hoists, breakout wrench, 750 gallon water tank  Price:  $65,000

MOBILE B57 (Ref#11450N) Manufactured 1986, Cummins engine, mounted on ORV, only 2000 hours, drop hammer (not auto), in-out slide base, Moyno 3L6 pump, water tank, 3 winches, 1 front 2 rear hydraulic leveling jacks, excellent condition   Price:  $85,000  PRICE REDUCED:  $63,000

MOBILE B57 (Ref#15264N) Manufactured 1987, Ford gas deck engine, mounted on 1996 International 4700 (not 4x4) with DT466 engine, cathead, mainline winch, safety driver, 3L6 Moyno pump, in-out and side to side slide base, swing out auger rack, no auto hammer, 100’ of 6” solid flight augers, good condition, currently drilling  Price:  $55,000  PRICE REDUCED:  $39,500

MOBILE B-57  (Ref#7219N)  Manufactured 1986, 6 cyl gas deck engine, mounted on mobile ATV, Moyno pump, drilling now  Price on Request

MOBILE B-57  (Ref#2117Nb)  Manufactured 1983, mounted on 1993 International truck, PTO, new auto hammer, cathead, 3 winches, Moyno pump, 3 hyd leveling jacks, water tank, auger racks, toolboxes  Price:  $60,000

MOBILE B-57  (Ref#1768N)  Ford 6 cylinder gas deck engine, 3 winches, safety hammer, swing out auger racks, Moyno 3L6 pump, 200 gallon water tank, toolbox, mounted on 1989 Ford F700 truck with 429 V8 engine, 30’ of 6-1/2” augers, tools, good condition  Price:  $55,000

Also available: trailer

MOBILE B-57  (Ref#5865)  diesel on deck, Ford truck with diesel engine, Moyno 2L4 pump, 7’ stroke, 27’ mast, hyd. hammer, heavy duty winch, 3 hyd leveling jacks, 4 toolboxes, 2 auger racks, 150’ of 8” OD hollow stem, 100’ of 11” OD hollow stem, downhole hammer with bit, 40’ SFA, 8” hollow stem adapter to drill, 8” and 11” hollow stem bits, 50’ AW rod 5’ lengths, 2 split barrel sleeve samplers, 2.5” ID, cutting shoes   Price:  $90,000

MOBILE B57 (Ref#11355Na) mounted on single axle Ford truck, 3 winches, Moyno 3L8 pump  Price:  $50,000

MOBILE B57  (Ref#5124N)  mounted on Ford L8000 truck with diesel engine, Moyno 3L6 pump, in/out slide base, 140# auto hammer, no tooling  POR

MOBILE B-56  (Ref#13759N)  mounted on Ardbo buggy, 6 cylinder Ford Industrial engine on rig, 6 cylinder Ford Industrial engine in carrier, cathead, wireline hoist, main hoist, 3L8 Moyno pump, toolboxes, auger racks, 4 jacks, not articulating, no water tank, no autohammer  Price:  $35,000

MOBILE B-56  (Ref#14342N)  15’ mast, Ford turbo diesel deck engine, mounted on 1998 Ford F800 truck with Cummins engine, auger rack, toolboxes, 7000 watt generator, steam cleaner, 2 rear hydraulic leveling jacks, 50’ of 8” auger, 55’ of 4” auger, 55’ of 2” auger, tools, 350 gallon water tank, good condition  Price:  $55,000

MOBILE B-56  (Ref#502N)  Manufactured 1976, mounted on 1976 International truck, PTO, 100’ flight auger  Price on Request

MOBILE B-56  (Ref#8476N)  mounted on 1975 Ford F750 single axle truck with gas engine, (converted fire truck), 35,000 miles, 4 cyl gas engine on deck, in/out slide base,  new hydraulic hoses, new radiator, excellent shape, cathead, no auto hammer or tools, stored inside,   Price for rig:  $25,000

Available at extra cost:  new 3-1/4” HAS -

MOBILE B-56  (Ref#3995N)  Manufactured early 1970’s, Ford 4 cyl gas deck engine, mounted on 1979 Ford truck (not 4x4) with gas engine, cathead, 2 winches, in/out slide base, auger racks, no Moyno pump, no auto hammer   Price:  $25,000

MOBILE B-56  (Ref#13653N)  Manufactured 1960’s, mounted on ATV, refurbished 2 years ago, no tools or pipe  Price:  $50,000

MOBILE B-53  (Ref#786Na)  Manufactured 1990, mounted on Ford F700 4wd truck, PTO driven, Detroit diesel engine, no pump, no cathead, side to side slide base, auger racks hold roughtly 100’ of 3-3/8” auger, 2 rear leveling jacks, 1 front leveling jack, good running condition  Price:  $35,000

MOBILE B-53  (Ref#1585N)  Set up for auger and coring, Detroit diesel on deck, no angle capacity, cathead, 2 winches, mud pump, unmounted, no water tank, no breakout wrench, no auger racks, toolboxes, auto hammer  OFF MARKET

MOBILE B-53  (Ref#7001N) mounted on Hilyard 4 x 4 buggy with 453 Detroit engine, cathead, 18’ mast, 2 hoists, no auto hammer, in out and side to side slide base, 250 gallon water tank, auger racks, toolboxes, tools, pipe and HAS included, good condition  Price:  $52,000

MOBILE B-53  (Ref#3411N)  mounted on 1979 Bombadier, PTO, cathead, aux hoist, Moyno pump  POR

MOBILE B-53  (Ref#6440N)  mounted on 2005 Ford F650 XLT Super Duty truck with diesel engine, 7064 miles, Moyno 3CL6 (rebuilt), PTO, 3 hydraulic jacks, 23 winches, 10 speed rotary drill head, 150 gallon water tank, swing out auger rack, 6 tool boxes  Price:  $70,000

MOBILE B-53  (Ref#3310N)  Manufactred 1988, 4 cyl Hercules gas deck engine, mounted on 1988 International S1700 with Cummins engine, cathead, 2 winches, manual 140# hammer, 250 gallon water tank, 20’ mast, in/out slide base, 1 front 2 rear hyd leveling jacks, some tools and augers, good condition, currently drilling Price:  $45,000

MOBILE B-53  (Ref#1725N)  Manufactured 1991, mounted on International 4800 4x4 truck with  FABCO TC-38 heavy duty transfer case and PTO, engine rebuilt 2 years ago, 10-speed drillhead with 716 rpm top speed, hydraulic hi/low shifting from control panel, 250 gallon water tank, Moyno 3L6 water pump, hydraulic hoist, 2 hinging auger racks, toolboxes, Mobile Drill Safe-T-Driver sampling hoist, currently drilling  Price:  $70,000

MOBILE B-53  (Ref#5205N)  Manufactured 1989, mounted on 1989 Ford F700 truck, 3L8 Moyno pump, cathead, in/out slide base, 3 jacks,  Price:  $32,000

MOBILE B-53  (Ref#5220N)  Manufactured 1988, mounted on Ford F800 truck with diesel engine, PTO,Moyno 3L6 pump, side to side slide base, 2 wiches, toolbox, safety driver, swig out auger racks, 3 jacks, no cathead, no autohammer  Price:  $55,000

MOBILE B-53  (Ref#2348N)  Manufactured 1987, PTO, mounted on 1998 International 4700 4 x 2 truck with rebuilt diesel DT466e Turbo and 6 speed transmission, 25,500# GVW, Safe-T Driver hoist,, 4,500 lb Pullmaster hoist,  (no cathead), 140# hammer, 2 winches in/out slide base with 16” travel, , Slide-O-Matic head, 250 gallon water tank, Liberty XL6 pump, 10 speed transmission, dual fan hydraulic cooler, 3 hyd leveling jacks, rod/tooling storage on deck, (2) toolboxes on deck, PTO drive,  some tools and augers,   Price:  $70,000

MOBILE B-53  (Ref#909Na)  Manufactured 1987, mounted on Ford F700 truck (not 4 x 4) with diesel engine, PTO, 3 winches, safety driver, cathead, side to side slide base, 3L8 Moyno pump, 3 hyd leveling jacks, no augers  Price:  $35,000

MOBILE B-53  (Ref#2117Na)  Manufactured 1986, mounted on 1986 Ford F700 truck with diesel engine, PTO, new autohammer, cathead, Moyno pump, 2 winches, hyd leveling jacks, auger racks, toolboxes  Price:  $40,000

MOBILE B53 (Ref#12374N) Manufactured 1986, completely rebuilt, PTO, mounted on Bombadier Muskeg with Perkins diesel engine, no slide base, 2500# safety driver, 6000# main winch, Moyno 3L6 pump, no auto hammer or cathead, no tools or augers, 3 hydraulic leveling jacks  Price:  $165,000

MOBILE B53 (Ref#8739Nb) Mounted on 1985 Ford F700 (not 4x4)  Price:  $40,000

MOBILE B-53  (Ref#8717N)  mounted on 1985 Ford LNT8000 tandem axle truck with diesel engine, PTO, Gardner Denver 4-1/2 x 5 mud pump, cathead, in/out slide base, 2 aux winches, 1 main winch, 700 gallon water tank, 4 hydraulic leveling jacks, toolboxes, auger racks, good condition  Price:  $80,000

MOBILE B-53  (Ref#1470N)  Manufactured 1985, mounted on 1980 Ford LN8000, Cat engine, 4 x 4 chassis (4x4 capacity has been disconnected), rear jacks, 2 winches, 250 gal water tank, water pump, 3 swing out auger racks, 3 tool boxes, Cummins deck engine, good condition, currently drilling  Price:  $65,000

Available at extra cost:

Support Equipment Package:

Available at extra cost:   Support Equipment Package includes D-Con trailer, hot water washer, drop hammers, drills extensions, adaptors, rods, split tube samplers, 1.5” and 2.5”, (+- 100 samples tubes), 10-15 bits, 6” & 12” cycling through rebuilding process, used hollow stem auger, cycling through rebuilding process, approx (60) ea 6”, 8” 12”, practically new (24) 6”,  auger bolts and bushings, other miscellenaous tools and equipment   Support package: $25,000

MOBILE B-53  (Ref#2517N)  PTO, mounted on 1984 International 4800 truck with DT466 engine, hydraulic chuck, 3000# aux hoist, sandline, cathead, 2 rear hydraulic leveling jacks, good condition  Price:  $60,000

MOBILE B-53  (Ref#1711Na)  Manufactured 1981, mounted on 1981 International 6 x 4 truck with diesel engine, 3L6 Moyno pump, safety driver, cathead, 3 winches, 300 gallon water tank, auger rack, good condition  Price:  $35,000   OFF MARKET

Tools available at extra cost

MOBILE B-53 (Ref#606N)  Refurbished 4 cyl diesel on deck, Cathead, water tank, mounted on Ford w/ Cummins 6 speed diesel, 3 winches, 2 jacks, breakout wrench, Beam 435 pump  Price on Request

MOBILE B-53 (Ref#2453N) Manufactured mid 1980’s, PTO, mounted on Ford F700 (not 4x4) with gas engine, in-out and side to side slide base, no auto hammer, no cathead, 2 rear hydraulic leveling jacks, 100 gallon water tank   Price:  $24,500

MOBILE B-53  (Ref#410N)  Manufactured 1980’s, Deutz diesel engine on deck, mounted on 1989 Ford 800 truck with diesel engine, air brakes, safety hammer, cathead, Moyno pump, winch, 2 auger racks, 3 jacks  Price:  $27,500

MOBILE B-53 (Ref#9752Na) Manufactured 1980, 353 Detroit deck engine, mounted on 1978 Ford 4 wheel drive with gas engine, hydraulic chuck, extended mast, in-out slide base, cathead, mainline, sandline & wireline winches, no auto hammer, 435 Bean pump, underbody swing out auger rack, toolbox, no water tank, 3 hydraulic leveling jacks  Price:  $60,000

MOBILE B-53  (Ref#14406N)  Manufactured 1980, Wood Tiger, cathead, 4 jacks, winch, Detroit power  Price:  $25,000

MOBILE B-53  (Ref#13469)  Manufactured 1979, mounted on Ardco JXF buggy, less than 500 hours on complete overhaul, 425 Bean pump, 3 hoists 7000#, 2900# and safety driver, new hydraulics, PTO, Detroit diesel in buggy, 250 gallon water tank, 20,000# winch on front, good condition  Price:  $45,000

MOBILE B-53  (Ref#5193N)  Duetz diesel deck engine, mounted on Ardco buggy with Ford 300 6 cyl gas engine, 1 winch, hydraulic cathead, Moyno 3L6 pump, set up for auger and coring, in/out slide base, auger rack, toolbox  Price:  $25,000

Tools and augers available at additional cost

MOBILE B-53  (Ref#15132Na)  mounted on Hilyard buggy with 353 Detroit engine, 3L6 Moyno pump, PTO, 2 winches, cathead, auger and rod rack, toolboxes  Price:  $50,000

MOBILE B-53  (Ref#15132Nb)   mounted on Ford F600 truck with diesel engine, PTO, 3L4 Moyno pump, cathead, 2 winches, 3 leveling jacks  Price:  $40,000

MOBILE B-53  (Ref#3391N)  Manufactured 1989, PTO, mounted on 1992 Ford F800 4 wheel drive truck with Cummins engine, Moyno pump, cathead, 30’ extended mast, 300-350 gallon water tank, good condition.  100’ j RODS, 100’ aw rods, 40’ 4-1/4” hollow stem augers, 4 cutter heads  Price:  $90,000

Tools available at extra cost

MOBILE B-53  (Ref#965N)  Manufactured 1990, mounted on 1992 Ford F800 truck with Ford diesl engine, PTO, 2 winches, air brakes, 150 gallon water tank  Price:  $50,000

MOBILE B-53  (Ref#12627N)  Manufactured 1988, mounted on International 4700 with diesel engine, safety driver, 2 winches, extended mast, swing out auger racks, toolbox, water tank, 3 hydraulic leveling jacks, no cathead, no tools or augers  Price:  $42,000

MOBILE B-53  (Ref#2397N)  Manufactured 1979, mounted on Wood Tiger Cub track carrier, Chevy Industrial engine, 1-1/2 x 2 Mission pump, water tank  Price on Request

MOBILE B-53  (Ref#6392N)  Manufactured 1971, mounted on 1971 International single axle 4-wheel drive truck with gas engine, 3000# and 5000# winches, cathead, 300 gal water tank, side to side slide base, auger rack, toolbox, rod rack, 3 hydraulic leveling jacks, some tools and augers, ready to go  Price:  $35,000

MOBILE B-53  (Ref#12230N)  Mounted on single axle 1985 Chevy C70 Kodiak truck with Cat diesel engine, 50’ of 6” augers, good condition  Price:  $43,500

MOBILE B-52 (Ref#147Na) Manufactured 1970, 4 cylinder gas deck engine, mounted on 1970 Chevy single axle truck with 366 gas engine, in-out slide base, cathead, auger racks, no auto hammer, 2 rear leveling jacks  Price:  $22,000

MOBILE B-52A  (Ref#11175)  Manufactured 1964, straight 6 Industrial grade Ford motor on deck (low hours), mounted on International Loadstar 1600 all-wheel drive with a new 304 Industrail V8 engine, fully tools, 4” augers, bits, 200’ depth capacity, good condition, currently drilling  Price:  $45,000

BRAINARD KILMAN (LONGYEAR) BK51 (Ref#1896N) Manufactured 2000, Duetz diesel engine, 2000# & 5000# Pullmaster winches, direct drive cathead, Moyno 3L6 pump, SPT hammer, angle drill capability, water tank, front buggy winch, auger racks, rod racks, remote control, hydraulic rubber tracks, used for coring and soil sampling  Price:  $95,000  PRICE REDUCED:  $80,000

MOBILE BK51 (Ref#4209N) Manufactured 1995, Deutz diesel turbo deck engine, mounted on 1995 Ford F700 4x4 with 429 gas engine, cathead, in-out slide base, 2500# & 5000# winches, Moyno 3L8 pump, no auto hammer, 500 gallon water tank, rod racks, auger racks, toolboxes, 1 front & 2 rear hydraulic leveling jacks  Price:  $60,000  PRICE REDUCED:  $45,000

BRAINARD KILMAN (LONGYEAR) BK51 (Ref#7969N) Manufactured 1991, Deutz diesel deck engine, mounted on 1991 Ford F700 4x4 with 460 gas engine, in-out slide base, 5000# & 2000# winches, cathead, 500 gallon water tank, Moyno 3L6 pump, 3 leveling jacks  Price:  $70,000  PRICE REDUCED:  $40,000

MOBILE BK51 (Ref#2429N) Manufactured 1990, completely refurbished, 3 cylinder Duetz diesel deck engine, mounted on 1990 Ford F700 4x4 with gas engine, cathead, in-out and side to side slide base, 3L6 Moyno pump, 500 gallon water tank, no auto hammer, toolboxes, rod racks, 1 front & 2 rear hydraulic jacks  Price:  $47,500

Tools & augers available at extra cost

MOBILE BK51 (Ref#4342N) Manufactured 1990, Duetz diesel deck engine, set up for auger, wireline & coring, mounted on early 1980’s Chevy with 350 gas engine, 5’ stroke, Moyno 3L2 pump, in-out slide base, main hoist, 400 gallon water tank, no angle capability, no auto hammer, no cathead, (3) 36” leveling jacks, needs TLC  Price:  $18,500

MOBILE B53 (UPGRADED FROM B50) (Ref#3606N) PTO, mounted on Ardco buggy with only 10 hours on rebuilt diesel engine, side to side slide base, cathead, 3L6 Moyno pump, breakout wrench, mud pump, no air (but set up is there), no auto hammer, 50’ of 3 ¼” HAS, 50’ AW rods   Price:  $35,000

MOBILE B-50  (Ref#782N)  Manufactured 1977, set up for auger and coring, track mounted on 1970 IH-TD8C engine, 6 way hydraulic blade, cathead, sandline, 5000# Braden hoist, hydraulic Bean injection pump, good condition  Price:  $60,000  PRICE REDUCED:  $43,000

MOBILE B-50  (Ref#3406N)  Manufactured mid 1970’s, mounted on 1963 Chevy C60 series 235hp 6 cyl engine, PTO, tophead swivel for air and mud, 60’ of 6” auger, 20’ of 8” overdrive drill casing, 6” and 8” cutter bit, outriggers on rear end, aux hydraulic tank, 2” diameter pipe, cathead, sandline  Price: $60,000

MOBILE B-47 (Ref#2412Na) mounted on ATV with blade, 353 Detroit diesel engine, low hours  Price:  $35,000

MOBILE B-40  (Ref#1822N)  Manufactured 1985, mounted on 1985 Chevy C70 truck, Chevy 350 engine (needs repair), PTO, 18’ mast, cathead, swing out, set up for 2” , rig needs work  Price:  $18,500

Available at extra cost:

8” CME hollow stem ID auger, screw together (50’), excellent condition  Price:  $3,500

3-1/4” CME hollow stem ID auger, screw together (50’), excellent condition  Price:  $3,500

3-1/4” bit and 8” bit  $300 each

MOBILE B-40  (Ref#1955N)  Perkins diesel deck engine, 185/125 on board air compressor, 3L6 Moyno pump, 2 winches, mounted on 1978 Ford F8000 tandem axle truck with 391 gas engine, allnew hydraulics, good condition  Price:  $65,000

MOBILE B40  (Ref#84Na)  diesel engine on deck, 185 air, 3” diaphragm pump, Moyno pump, 4 brand new hydraulic pumps, new 10,0003 hydraulic winch, mounted on tandem axle truck with gas engine  Price:  $$52,500

MOBILE B-47  (Ref#15021)  setup for auger and wireline coring with all down-hole tools and pumps, mounted on 1978 Bombardier Musket tracks with Perkins diesel engine, 4 cyl Deutz drill engine, 15’ mast with hydraulic crown,  lots of extras: 100’ 4-1/4 ID CME hollow stem auger with bits, center rod, split spoons, 140# drop hammer, 2 Bean 20 water pumps, water swivel, 400’ NQ and 400’ BQ drill rod with core barrels and bits, 100’ of 5’ NW casing with Christiansen casing advancer, lots of spares, complete set of hand tools, complete with 20’ container containing parts set up for coring and drilling.  Work done on rig:  Bombadier painted, tracks and rollers reworked, on rig pulldown cyoinders reworked, hydraulic valve bank reworked, rebuilt wireline and hydraulic motor   Price:  $65,000

MOBILE B-47  (Ref#1361N)  Manufactured 1980, mounted on 1995 Ford F350 4x4 truck with powerstroke diesel engine, water pump, leveling jacks, (8) 5’ augers, split spoon sampler with 5 extension rods, 3 rock drill bits, 2 toolboxes, good condition, currently working  Price:  $40,000  OFF MARKET

MOBILE B-40 (Ref#4155N) Duetz diesel deck engine, mounted on Ardco buggy with Ford 300 gas engine, flotation tires all around, cathead, 200 gallon water tank, 20’ mast, no slide base, Shelby tube extractor, currently drilling   Price:  $45,000

Available at extra cost:  lowboy trailer, tools

MOBILE B-40  (Ref#13425)  mounted on 1996 Dodge 3500 4 x 4 truck with Cummins diesel engine, 3 jacks, cathead,  5’ stroke, in/out slide base, toolbox  Price:  $43,000

MOBILE B40L12  (Ref#1878N)  Manufactured 1986, Ford 4 cyl Industrial gas engine, mounted on GMC Brigadier truck with Cat 3208 diesel engine, 5 x 6 Gardner Denver mud pump, cathead, in/out slide base  Price on Request

MOBILE B40  (Ref#14987N)  Manufactured 1985, munted on 1985 Ford F8000 with Cat 3208 engine, PTO, 11’ stroke, uses 10’ pipe, 500 gallon water tank, oversized oil cooler, 3L6 Moyno pump, hydraulic walking beam, hydraulic winch  Price:  $65,000

MOBILE B40  (Ref#12624N)  mounted on International S2500 tandem axle w/Cummins engine, PTO, 22’ stroke, Moyno pump, 1 winch, in/out slide base, developmental air compressor, mud pan, 80 gallon hydraulic tank, no cathead or autohammer, 2-3/8 IF x 15’ drill pipe, good condition  Price:  $50,000  OFF MARKET

MOBILE B40 (Ref#3301Na) Manufactured 1969, 4 cylinder Continental gas deck engine, Mounted on 1989 Ford F700 (not 4x4) with 6 cylinder diesel engine, cathead, in-out slide base, winch,  250 gallon water tank , 2 rear hydraulic leveling jacks, auger racks, toolbox, no tools  Price:  $29,500

MOBILE B40L (Ref#6677R)  trailer mounted with Detroit 353 engine, Sullair 375cfm air compressor, set up for hammer drilling, coring & augering, in-out slide base, no water tank, no pump  Price on request

MOBILE B40L  (Ref#845Na)  6 cyl Ford Industrial engine on deck, mounted on Kenworth tandem axle truck with 400 Cummins engine, augers, tools, etc., ready to drill  Price:  $40,000

1987 INTERNATIONAL NAVISTAR F1954 6X6 WATER TRUCK  (Ref#845Nb)  DT466 engine, 1000 gallon Flatwater tank, auto crane, hydraulic fill pump, front winch, toolboxes  Price:  $19,000

MOBILE B-38  (Ref#14619)  Manufactured 1968, 4 cyl Ford 110 hp Industrial motor, tower for drive casing, skid mounted, 80’ of 5-1/2” augers, 80’ of 3-1/2” auger, 5’ sections, no mud/air, set up for test bore and wells, sitting 9 years    Price:  $8,500

MOBILE B-34  (Ref#909Nb)  Manufactured 1986, mounted on Mack truck with diesel engine, safety driver, main winch  Price:  $35,000

MOBILE B-33  (Ref#9090N)  Manufactured 1977, mounted on Ardco Super L ATV, Ford Industrial gas engine, PTO, 3L4 Moyno pump, solid stem auger 4” OD, 2 winches, 607 hours, drop hammer  Price:  $80,000  PRICE REDUCED:  $55,000

MOBILE B-30  (Ref#11942)  Reworked 1997, mounted on ¾ ton Jeep truck 4x4 with gas engine, PTO, 60’ of 6” auger, auger fishing screw, clay and rock bits  Price:  $22,000

MOBILE B-30 (Ref#9024N) Ford 4 cylinder gas deck engine, mounted on 1976 Ford with V8 gas engine (not 4x4), in-out slide base, new 4 ½” cutterhead, auger racks, toolbox, no cathead, 20’ of 3” solid stem augers, 20’ of 4” solid stem augers  Price:  $16,500

MOBILE B-24  (Ref#6346N)  Manufactured 1991, all hydraulic, larger pump and motor creating more torque, powered by 4 cyl Wisconsin motor, Shelby tube extruder, hyd set up for rotary wash, drill head / slide-amatick, 1 winch line, drill rod box, auger rack, 2 toolboxes, cathead, mounted on 1999 F350 Super Cab 2-wheel drive with 7.3 diesel engine, 226,000 miles, wellmaintained, stored inside when not in use., 35’ of 6” auger, 35’ of drill rod, auger catch, split spoon, drop hammer  Price:  $40,000

MOBILE B21 (Ref#3881NB) mounted on Ford 1 ton, no tools  Price:  $18,500

LONGYEAR BK-81 HDX  (Ref#5979N)  Manufactured 1994, mounted on 1994 Ford L8000 truck, 134000 mies, 2000# and 8000# winches, safety-driver hoist, 3L8 Moyno pump, 22,000 ft/lb torque, excellent condition, well maintained, extra parts available  Price:  $100,000  OFF MARKET

LONGYEAR BK-81 HDX  (Ref#12895N)  Manufactured 1993, mounted on 1993 Ford L800, 169,000 miles, 2000# and 12,000# winches, safety-drive hoist, 3L8 Moyno pump, rod table, breakout wrench, 22,000 ft/lb torque, excellent condition, well maintained, extra parts available  Price:  $100,000  OFF MARKET

GEOPROBE 6620DT  (Ref#2575N)  Manufactured 2008, track mounted, low hours, remote control, low hours, 140# split spoon auto hammer, no tooling  Price:  $95,000  OFF MARKET

GEOPROBE 6620DT  (Ref#3796N) Two available, manufactured 2004 and 2007, well maintained, approx 1800 hours, track mounted, Kubota diesel engine, remote control, 2/8” probe rod, 2,000# winch, 66” stroke, auger head (optional)  Price:  $100,000 each

GEOPROBE 66DT  (Ref#786Nb)  Manufactured 2002, track mounted, Jubota engine, autohammer, winch, ice auger, fully tooled for geotech sampling and environmental work  Price:  $65,000

GEOPROBE 5410 (Ref#2494N) Manufactured 2003, only 2300 hours, mounted on 2003 Ford F350 all wheel drive with diesel engine, no remote, some soil sampling tools, 1 ½” rods  Price:  $50,000

GEOPROBE 5410 (Ref#6945N)  Manufactured 2003, mounted on 2003 Ford 4x4 F350 extended cab, 6.0 diesel engine, 5 speed Auto transmission, GH42 hammer, 136,000 miles  Price: $50,000

GEOPROBE 5410  (Ref#441Nb)  Manufactured 2002, hydraulic oil cooler, onboard water tank and pump, Geoprobe GH42 hammer, 2938 hours, mounted on Ford F350 4x4 truck with 7.3L diesel engine, automatic transmission, extra cab and tow package, 219,191 miles, (2) rod racks, overhead storage, vise  Price:  $60,000

GEOPROBE 5410  (Ref#441Nc)  Manufactured 2001, hydraulic oil cooler, onboard water tank and pump, Geoprobe GH42 hammer, 3039 hours, mounted on Ford F350 4x4 truck with 7.3 L diesel engine, new automatic transmission (at 121,897 miles), current miles 129,102 miles  Price:  $55,000

GEOPROBE 5410  (Ref#441Na)  Manufactured 2001, hydraulic oil cooler, onboard water tank and pump, Geoprobe GH42 hammer, 3058 hours, mounted on Ford F350 4x4 truck with 7.3L diesel engine, rebuilt automatic transmission, extra cab and tow package, (2) rod racks, overhead rack, vise   Price:  $50,000

GEOPROBE 5400  (Ref#5695N)  Manufactured 1999, 4996 hours, mounted on 1999 Ford F250 4x4 truck with 202k miles.  Tooling:  (19) 1.25” x 4’ rods (6 new), (4) 4’ macrocore tubes (2 new), (2) 1.25” pull caps (new), (3) macrocore cutting shoes (new), (1) macrocore drive head (new), (3) macrocore drive head caps (new), (3) boxes 4’ liners  Price:  $20,000

GEOPROBE 5400  (Ref#14403Nb)  Manufactured 1999, mounted on 2006 Ford F350 flatbed truck, 11,400 miles, 2 ltr powerstroke diesel engine, micro core samples  Price:  $50,000

GEOPROBE 5400  (Ref#8536N)  Manufactured 1996, mounted on 2004 Ford 250 truck, PTO, 6.3 liter diesel engine, some tooling  Price:  $36,000

GEOPROBE 5400  (Ref#2068N)  Manufactured 1995, mounted on 1996 Dodge 2500 4 wheel drive truck, diesel engine, aprpox 250,000 miles on truck, PTO, geared for 4’ tooling, 5’ stroke, Macro core liners, tool rack, fully tooled,  rig in excellent condition, truck needs work  Price:  $28,000

GEOPROBE 5400 (Ref#7798Na) Manufactured 1995, mounted on Ford F250 4x4 with gas engine, PTO, 4’ stroke, Okada OKB300 hammer, new macrobarrel & rod extractor, vacuum pump, decon tank, fully tooled   Price:  $23,000

GEOPROBE 5400  (Ref#419Nc)  mounted on 1995 Ford F250 4x4 truck with 351 gas engine, PTO, no cathead  Price:  $28,500  OFF MARKET

GEOPROBE 5400  (Ref#5368N)  Manufactured 1995, mounted on 1993 Chevy Silverado 4x4 with gas engine, some tools  Price:  $25,000

GEOPROBE 5400  (Ref#4078N)  Mounted on 1995 F350 4 wheel drive truck, 460, auto, a/c, completely tooled  Price:  $35,000

GEOPROBE 5400  (Ref#14535)  mounted on 1996 Ford F250 4 x 4 truck with diesel engine, PTO, good condition  Price:  $30,000

GEOPROBE 5400 (Ref#9443Na) mounted on 1996 Ford F250 4x4  Price:  $28,000

GEOPROBE 5410 (Ref#5056N) Manufactured 2006, only 565 hours, PTO, mounted on 2007 Ford F350 4x4 with diesel engine, 50 gallon water tank & pump, 2 rod racks, storage, includes 7x12 cargo trailer, no tools available  Price:  $78,500

GEOPROBE 5400  (Ref#15053b)  Manufactured early 1990’s, truck mounted, fully tooled,  Price Open

GEOPROBE 540B  (Ref#14403Na)  Manufactured 2002, not mounted, approx 1200 hours, 40’ x 1-1/4 rod  Price:  $35,000

GEOPROBE  (Ref#15034)  mounted on 1992 Chevrolet truck, new style hammer  Price:  $32,500

GEOPROBE 54DT  (Ref#14631)  2 available, rubber track mounted with diesel engine,  Price:  $40,000 each

GEOPROBE 54DT  (Ref#12921N)  Manufactured 1999, 1186 hours, no tools, track mounted, GH42 hammer, Kubota diesel engine  Price:  $42,500

AMS POWERPROBE 9630-PTO  (Ref#9323N)  Manufactured 2003, hollow stem capability, 80” probe stroke, 5’ push, 175 ft/lb hydraulic hammer, water tank, mounted on Ford F550 2-wheel drive w/7.3 liter diesel engine, freshly painted, no tooling  Price:  $75,000

AMS POWERPROBE 9630  (Ref#15050)  Manufactured 2004, direct push unit, mounted on 2004 Ford F550 truck, fully tooled 

Price rig only:  $115,000                                   Tooling:  $20,000                AMS heavy duty trailer:  $6,000

AMS 9600DC POWER PROBE (Ref#7798Nb) Manufactured 2000, unmounted, low hours, 2400 ft/lb AGR, T-300 hammer, fully tooled  Price:  $25,000

AMS POWERPROBE 9600DC  (Ref#3357Na)  Manufactured 1997, mounted on 1997Chevy 2500 4x4 extended cab truck with Cheyene 5.7 motor, manual trans, 160,000 miles , Isuzu diesel deck engine, SK38 hydraulic hammer, uses 4’ Geoprobe tooling (basic tooling comes with the rig)  Price:  $35,000 

AMS POWERPROBE 9500  (Ref#3794Na)  Manufactured 2006, 52 hp Isuzu diesel engine, 2 speed 2400 ft/lbs auger motor, AR62 550 ft/lbs @ 1100 bpm hammer, 72” mast stroke, 1000 hours  Price:  $97,500

AMS POWERPROBE 9500 (Ref#3794Nb)  Manufactured 2004, 52 hp Isuzu diesel engine, 2 speed 2400 ft/lbs auger motor, AR62 550 ft/lbs @ 1100 bpm hammer, 72” mast stroke  Price:  $90,000

DEEPROCK 10K  (Ref#4519N)  Manufactured 1995, 3 x 4 centrifugal mud pump, 3L6 Moyno pump, mounted on 2001 Ford F650 single axle truck with Cummins engine, 4 hydraulic leveling jacks, swing out auger racks, cathead, safety hammer, 2 winches, 5’ stroke, 2 speed tophead 0-130 rpm and 0-65 rpm, 5000 ft/lb and 10,000 ft/lb torque, 16,000# pulldown, 20,000# pullback, complete with tools, augers and drill pipe, good condition  Price:  $65,000

DEEPROCK DR10K (Ref#1542Na) Manufactured 1994, PTO, mounted on Mitsubishi tandem axle truck with diesel engine, no cathead, wireline winch, Moyno pump, 10000ft/lbs torque, 11’ stroke, hydraulic hammer, winches, angle drilling, in-out slide base, leveling jacks, toolboxes, auger racks  Price:  $60,000  OFF MARKET

DEEPROCK 3-K  (Ref#10437)  1300 hours, John Deere 75 hp deck engine (200 hrs), mounted on 1995 International truck (low profile) with DT 444E engine, excellent condition, 3000 ft/lb torque, used for environmental holes 20 – 25’ deep.  Can adapt water swivel to hydraulics head and add 3 x 2” centrifugal pump for water wells.  Augers and drill rod available.  Price:  $90,000

CYCLONE 42R ROTARY/TABLE COMBINATION RIG  (Ref#5173N)  Ford Industrial gas deck engine, mounted on 1972 Kaiser 6 x 6 truck with 6 cyl Turbo diesel engine, (both engines rebuilt), 5” stationary table, 4” x 12’ square kelly, King swivel, portable mud pit, 5” and 6” tools, no mud or air, no leveling jacks, no pipe  Price:  $45,000

CYCLONE 42  (Ref#6034N)  3 drum, mounted on 1991 GMC single axle truck, screw jacks, gasoline engine, International 4 cylinder gasoline engine on deck, tools 6” and 8” bits, stem, bailer, operating rig  Price:  $23,000

CYCLONE 40 (Ref#12026Na) Manufactured 1966, propane/gas deck engine, mounted on 65 Ford cabover with propane engine, 3 line machine, 2 rear mechanical leveling jacks, good condition, currently drilling, fully tooled, bits, bailers, stems. Jars, etc.  Price:  $45,000

CYCLONE 36/TH60  (Ref#5048N)  600/250 on board air compressor, 3 x 4 Mission mud pump, mounted on 1972 Ford L8000 truck with Cat 3208 Turbo engine, PTO, good condition, ready to go, no pipe or tools  Price:  $145,000

CYCLONE 36/TH60 COMBINATION RIG  (Ref#3423N)  Manufactured 1978, Gardner Denver 6” storke duplex mud pump, Mission 3 x , mounted on International Paystar 5000 truc,k, new front tires, new (8) rear tires, new King swivel, rebuilt hydraulic motors, 320’ of 2/=-7/8” HD pipe, stabilizer, bits  Price:  $100,000

CYCLONE 36/TH60 (Ref#4246Na) Manufactured 1974, PTO, mounted on 1974 Ford L8000 6x4 with Cat 1160 diesel engine, 5x6 piston mud pump, Leroi 50SDS air compressor, hydraulic powered retractable tophead drive, rod box, line oiler, water injection pump, mud pan, conductor pipe, 1 front & 2 rear hydraulic leveling jacks, 315’ of 3” OD x 15’ drill pipe 2 3/8” IF  Price:  $75,000

CYCLONE 36/TH60 (Ref#4246Nb) Manufactured 1970, PTO, mounted on Champion 6x6, 5x6 piston mud pump, Leroi 50SDS air compressor, main winch, drillers stand, rod box, 1 front & 2 rear hydraulic leveling jacks, no tools  Price:  $75,000

CYCLONE 36  (Ref#78N)  2 available, mounted on 1975, 4 cylinder Continental engine, both rigs come with bailer, jar, bumper and mud bucket

(a) mounted on 1975 GMC 6500 truck with 4 cyl Continental gas engine, 2 piece hydraulic mast, hydrolift, burn sockets, 5-1/2” carbide button bit, fully tooled for 6” – Price:  $30,000

(b) mounted on 1974 Chevy truck with 4 cyl C60 engine, single piece hydraulic mast, on board belt driven Hobart DC welder, no tools – Price:  $26,000

Jack shaft rebuilt with new bearings, new clutch and friction wheel, bailer, jar bumper, good condition 

CYCLONE 36A   (Ref#10498)  combination auger/cable tool, 4 cyl Ford Industrial deck engine, mounted on 1992 International 2900 with 466 International diesel engine, 38’ hydraulic mast, 2 rear jacks, 2 front jacks, 100’ of augers, tooled for 4”,  Price:  $50,000

CYCLONE 36  (Ref#2442N)  Manufactured 1965, mounted on 1965 International V8 truck with gas engine in truck, Ford gas deck engine, 3 line machine, set for 4” tools, it has been stored inside for 25 years  Price on Request

CYCLONE 36  (Ref#4791N)  Manufactured 1964, Ford 300 6-cyl on deck, mounted on 1975 International truck with DT466 diesel engine, 36’ mast, 3 lines, 500’ of ¾” drilling line (new), 500’ sandline (new), 150’ casing line (new), hydraulic jacks, 6” string of tools  Price:  $19,500

SANDERSON CYCLONE 36  (Ref#4794N)  4 cyl Butane deck engine, mounted on 1972 GMC truck with gas engine, 3 hydraulic jacks, 3 drums, drill spudder, 600’ cable, 2 winches, all tools, jars, stem, wrenches, bailer, etc., sitting 5 years  Price:  $25,000

CYCLONE 36 CABLE TOOL/AUGER COMBINATION RIG  (Ref#1576N)  diesel deck engine,mounted on 6 x 6 Army truck with Mack diesel engine, 2 catheads, sandline, 3 hyd leveling jacks, tools and augers included   Price:  $50,000

CHICAGO PNEUMATIC TOPHEAD / AUGER RIG  (Ref#14389)  mounted on 1974 Paystar 5000 with Detroit 6V53 engine, Mission 3 x 4 centrifugal pump, water tank, auger racks, augers, cutters, cont. samplers, breakout cylinder, 160’ of 2-3/8” Mayhew Jr pipe, good condition  Price:  $55,000

GEOSPACE 750  (Ref#15249)  Manufactured 1970, 100 cfm Westinghouse developmental air compressor, 2L10H Moyno pump, winch on front, mounted on 1974 Ford F600 truck with 391 Ford engine (new 5 – 6 years ago), hydraulically driven,  200-300’ Mayhew Jr. pipe, stabilizers, bits, needs rotator and stater, freshly painted   Price:  $25,000

GEOSPACE 800 (Ref#5088N) Manufactured 1980, PTO, mounted on 1987 Ford F700 (not 4x4) with diesel engine, 3 x 4 centrifugal mud pump, deck mounted grouter with Bowie pump, hydraulic leveling jacks, pipe rack  Price:  $49,500

Pipe & tools available at extra cost

D & R MINI SONIC CORE RIG (Ref#433N)  Manufactured 2004, 1200 hours, Limited Access, Rubber track mounted, With Ford F700 Super cab, Allison transmission, 70,000 miles, 2006 Towmaster T24 Tilt truck bed

The Mini Sonic drill rig platform will be utilized for this sampling effort. The equipment is a limited access, rubber track mounted rig capable of angle drilling.

Additional Details:  Width – 72” Height – 13’ 5”, Length - 16’ Weight - 17,500 lbs, Angle Capability - greater than 35°, Rock Coring Air/Mud Rotary, Pullback - 16,000 lbs Winch - 8,000 lbs, Depth Capabilites:

Casing Size:

·         8” to 50’ depth

·         6” to 100’ depth

·         4” to 150’ depth

Stroke Length 84”, 2520 Cat Injection Pump, 221hp Deutz Diesel, 3L6 Moyno, Blue Star 9” Breakout Wrenches

The Sonic drill method has been selected for all of the external locations along with any internal sample point that is accessible to the equipment. A sonic drill head is used for the drilling and sampling method. The head is a technologically advanced, hydraulically activated unit that imparts a high frequency, sinusoidal wave vibration into the drill string to effectuate the cutting action at the bit face. The resultant cutting action forces a continuous core of the formation into the core barrel. Due to the high forces developed by the sonic head and the externally flush drill string, the excess formation material generated at the bit is forced into the borehole wall, resulting in the generation of little or no “cuttings” during the drilling and sampling process. Essentially the only waste stream from the sonic method is the actual soil core itself.

Price: $330,000   OFF MARKET

SHOP BUILT AUGER RIG  (Ref#3313N)  track mounted, 50 hp diesel engine, low clearance 8’, 3500 ft/lb torque, 70 lb auto hammer, 2 speed head, telescoping cylinders, in/out slide base, gimbel coupling  Price:  $80,000

SHOP BUILT SOIL SAMPLING RIG (Ref#9971N) PTO driven, not mounted, includes 25’ of continuous flight augers, split spoon samplers  Price:  $20,000

COMACCHIO MC 401/A  (ref#14437N)  Manufactured 2004, used for 6 months, designed for rotary drilling, hollow stem auger, DTH hammer drilling, capacity 10 meters hammer, 20 meters auger, uses 1’ auger, low weight, remote power pack, mast lenth 3204mm, designed for low head room, located England  Price:  £55,000  

COMACCHIO MCF04  (Ref#775Ntt)  Manufactured 2007, 4400 working hours, Deutz 2013 L04 diesel engine (171 hp), 6.500mm rotary stroke, radio remote control, (2) rod loaders, oscillating undercarriage  Price:  €180,000 (Euros)

LIMITED ACCESS 8X8 RIG (Ref#1542Nb) 80hp diesel engine, 6’ stroke, hammer, auger racks, 5’ W x 13’ L x 8’ H   Price:  $47,500

SHOP BUILT LIMITED ACCESS RIG (Ref#11482N) mounted on rubber tracks, 25hp gas engine, 100’ depth capacity, cathead, 4 hydraulic leveling jacks, no tools  Price:  $65,000

SHOP BUILT LIMITED ACCESS RIG (Ref#4890Ne) set up for direct push, mounted on Ford F550 4x4 with diesel engine & crane  Price:  $60,000

GEOTECH RIG  (Ref#1048N)  with Ford 300 6 cyl Industrial gas deck engine, mounted on Ardco articulating buggy with Ford 300 6 cyl Ind gas engine, cathead, no auto hammer  Price:  $35,000

OLATHE DRILL  (Ref#6585Nb)  4”, 6” and 8” auger, 150’ depth, Onan engine  Price:  $19,500

AUGER BARGE  (Ref#945N) 

Barge size:  25’ x 12’ x 2’6”

Stabilizing legs 4 hyd adjust 25’ 5” x 5”

Derrick:  25’ x 18” x 18” – 12’ horizontal travel, 20’ vertical lift

Drill auger engine (29.8 hrs), Cummins 2006, Model 4B 3.9 4-cylinder, gross hp/kw 110/82 @ 2200 rpm, fuel/disel 10 gal plastic tank

Hydraulic tank Force America 10” x 3’ x 5’

Winch: Tulsa hydraulic, cable ¼ x 50’

Drill pipe spinner hydraulic

Drill pipe (1) 4” x 14’

Drill bit (1) 12” x 8’ auger type

Drill with water flush

Pump: Honda with 20’ x 2” hose

Suction hose 2” x 12’

Pump hose Alfagomma T202 10 bar, 150 psi

General purpost

Hydraulic piling puller 4’ x 4” x 4”

Price:  $115,000

Tel:  516-536-7375          Fax:  516-536-7317         rigs@sunmachinery.com