6500' top head and mud rotary rigs for sale

INGERSOLL RAND RD20 RANGE III  (Ref#550N)

Manufactured 2000,

-          Range 3 Tower

-          Top Head Drive

-          120,000 pound pullback

-          40,000 pound pulldown

-          Cummins QSK 19 engine with 700 horse power

-          Cummins Deck engine completely replaced in May 2008, rig ran 10 months since then, Guessing at 50 hrs on engine

-          IR 1250/350 psi Deck Compressor

-          Whisperwatt 15 Generator mounted behind cab for doghouse power

-          Carrier Mounted drilling rig with Cat C 13 Engine

-          25 gpm water injection pump

-          55 gal hammer oiler

-          Single Rod Loader

-          New Main Derrick Lift cylinders installed in September 2008

-          Newly rebuilt drivers cab for rig crane carrier

2006 Sullair Airpac:   (unused)

-          Model number 900XH1150

-          Trailer Mounted

-          Cat powered engines

-          Twin air units rated for 350 PSI each

-          Both air unit have approx 5100 hrs

-          All units plumbed together

Custom Dog House:

-          Easy Access Front Porch

-          Custom Built House for all tools

-          Storage areas

-          Breezeway

-          3000 gal fuel cell

-          Work Bench

-          Drilling Supplies

-          Night work lights

-          All mounted on 40’ trailer

Tubs and Pipe:

-          2 identical tubs with tugger winch mounts

-          3500’ of Star Iron pipe

-          2500’ additional pipe may be available

Sub-Base:

-          Height: 2 feet

-          Width: 9 feet

-          single unit with fold down front ramp

Miscellaneous:

-          Center Rock 12” Hammer and stabilizer/Collar

-          Center Rock 8” hammer and stabilizer/Collar

-          Necessary change over subs

-          Regan 3000# BOP and Air bowl (No Closing Unit)

-          Air controlled Tugger Winch

-          Air Slips

Pictures shown below were all taken this past winter.

The rig has not been used for drilling since these pictures were taken.

The drivers cab for the rig has been rebuilt.

(2) additional track mounted compressors

PRICE:  $750,000  PRICE REDUCED:  $500,000

WILSON MOGUL 42 DOUBLE DRILLING RIG  (Ref#495N)

Manufactured 1978

Draw Works:

-                      Single Drum Draw Works

-                      Foster Model 27 AH break out Cat heads (serial # 1404)

-                      Manual Braking System

-                      1,500’ 1” drilling line, spooled, never used, still in protective coating

-                      Driller’s console, with controls

Power:

-                      Detroit Model 12V71 diesel engine

-                      Engine rated for 550 peak Horse Power

-                      Radiator and Electric starter

-                      Allison Model TC955 torque converter

Mast :

-                      Wilson 102’ Height hydraulic derrick (serial #991-102-300)

-                      Hydraulically raised with multiple scooping raising arm

-                      Crown Block and Safety Platform

-                      Pipe racking board

-                      Standpipe

-                      3” (ID)  x 50’ long Kelly hose

-                      Tong counterweights

-                      Vapor proof lighting

-                      Martin – Decker weight indicator

Rig Mounted Equipment:

-                      Hydraulic Break Out Cylinder

-                      Winch

-                      Hydraulic Storage Tanks

-                      Fuel tanks

-                      Air compressor – Bendix Westinghouse Model TUFLO 1000

-                      Deadline anchor

-                      Hydraulic leveling jacks

-                      Folding walkways, with stairs and safety railings

-                      Rig Mounted on Tri Axle Trailer

Substructure:

-                      10’ Height

-                      16’ Width (with walkways extended)

-                      12’ Length

-                      2 piece substructure

-                      Box type structure, with rotary table beams

-                      10’ W x 40’L back on ramp

-                      Removable Stairways

-                      Folding walkways

-                      Safety railings

-                      Lighting

-                      Includes rat hole / mouse hole digger

 Travelling and Rotating Equipment:

-                      Chain Driven Rotary Table - Gardner Denver Model 175

-                      Split Master Bushing

-                      Swivel - Gardner Denver Model SW 125

-                      Kelly - Brand New 40’Length x 4 1/4” Square Kelly

-                      Drive Bushing

-                      Travelling Blocks - 3 sheave blocks, grooved for 1” line

-                      WEBB-WILSON Hydra Hook Elevator Bales

-                      Rig set up to add an extra travelling block to increase all capacities

-                      Air Head Oiler

Casing, Pipe and Equipment:

-                      7,000’ +/- 3 ½  OD drill pipe

-                      3 ½ ” IF connection

-                      4 ¾ ” OD flush drill collars, 3 ½” IF connections, slip recessed

-                      6 ¼ ” OD with 4 ½ “ X-hole connection drill collars

-                      2 Standard 32’ pipe trailers

-                      1 Extended 35’ center trailer

Well Control Equipment:

-                      Williams 11” annular BOP

-                      Washington Rotating head assembly, complete with 16 ¾” air bowl

-                      Assortment of Flanges including

o         Companion flange 13 5/8 x 13 3/8

o         Companion flange 13 5/8 x 9 5/8

o         Companion flange 13 5/8 x 7 inch

 Custom Rig Doghouse:

-                      8’W x 24’L trailer mounted dog house

-                      Easy Access Front Porch

-                      Rear porch where generator is mounted

-                      Custom Built House for all tools

-                      Storage areas

-                      Breezeway

-                      3000 gal fuel cell

-                      Geolograph

-                      Work Bench

-                      Drilling Supplies

-                      Night work lights

-                      All mounted on 40’ trailer

 Generator:

-                      Stateline 10 KV generator with all necessary Switching gear, gauges and controls, mounted on Rig Doghouse Porch

Miscellaneous Equipment and Parts:

-                      Tool Trailer

-                      Soap tank with MYERS Model C20-8CR injection pump and 1 ¼ “ lubricator

-                      Soap pump powered by Waukesha Engine

-                      Assortment of casing elevators and single side door elevators

-                      2” air pump

-                      Assortment of change over subs

-                      Dead man stakes and cable for rig tie down and secure lines

-                      Webb Wilson Type B tongs with assortment of tong jaws

-                      4 ½ “ bottleneck drill pipe elevators

-                      Drill collar slips

Air System (available at additional cost):

 2001 Ingersoll Rand Airpac:

-                      Model number XHP1170

-                      Twin air compressors included

-                      Trailer Mounted

-                      Cat powered C15 engines capable of 525 HP 

-                      Twin air units rated for 350 PSI and 1170 Cubic Feet each

-                      Both air unit have approx 7,600 hrs

-                      All units plumbed together

-                      compressor, complete with all necessary collers, gauges, valving and controls

Price:  $650,000     PRICE REDUCED TO $450,000

Wichtex C65A D/D (Ref#1616Nb) 

7000’ capacity, T-68-100 Wichtex derrick 65’ x 100,000# cable raised and telescoped, mounted on 1981 International F570 tandem axel truck with 350 Cummins, Oilfield front bumper, Full floating 31" x 8" double drum draw works, with air friction clutches, Franks right angle drive, 3 hydraulic outrigger leveling jacks, 450' of 7/8" tubing line, approx. 6,000' of 9/16" sandline, Spooling capacities: tubing drum 3785’ of 3/16” line, 2784’ of 7/8” line, sanline reel 7725’ of 9/16” line, 6250’ of 5/8” line,  tool racks, tool boxes, Auxiliary hydraulic circuit, winch, cat head, McKissick 50 ton 2-sheave block, currently working, good condition, ready for use

PRICE:  $125,000   PRICE REDUCED:  $105,000

Tooling available at extra cost:  links, tubing elevators with inserts for 1-1/2” – 2-3/8” tuabing, Guiberson air slips, Foster 58 power tongs, no rod tools, cable tools: rope socket, stems, jars 

PRICE WITH TOOLING:  $135,000  $120,000